Sony SPP-206 Bedienungsanleitung

Operating Instructions

Mode d’emploi

SPP-206

Cordless

Telephone

3-864-215-21 (1)

2EN

WARNING

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

To avoid electrical shock, do not open

the cabinet. Refer servicing to

qualified personnel only.

INDUSTRY CANADA NOTICE

NOTICE: The Industry Canada label

identifies certified equipment. This

certification means that the equipment

meets certain telecommunications

network protective, operational and

safety requirements as prescribed in the

appropriate Terminal Equipment

Technical Requirements document(s).

The Department does not guarantee the

equipment will operate to the user’s

satisfaction.

Before installing this equipment, users

should ensure that it is permissible to be

connected to the facilities of the local

telecommunications company. The

equipment must also be installed using

an acceptable method of connection.

The customer should be aware that

compliance with the above conditions

may not prevent degradation of service

in some situations.

Repairs to certified equipment should be

coordinated by a representative

designated by the supplier. Any repairs

or alterations made by the user to this

equipment, or equipment malfunctions

may give the telecommunications

company cause to request the user to

disconnect the equipment.

Users should ensure for their own

protection that the electrical ground

connections of the power utility,

telephone lines and internal meatallic

water pipe system, if present, are

connected together. This precaution may

be particularly important in rural areas.

Caution: Users should not attempt to

make such connections themselves, but

should contact the appropriate electric

inspection authority, or electrician, as

appropriate.

NOTICE: The Ringer Equivalence

Number (REN) assigned to each

terminal device provides an indication

of the maximum number of terminal

allowed to be connected to a telephone

interface. The termination on an

interface may consist of any

combination of devices subject only to

the requirement that the sum of the

Ringer Equivalence Number of all the

devices does not exceed 5.

IMPORTANT INSTRUCTION TO

USERS

Your model (SPP-206) has been

approved by the Industry Canada.

Note

Operation is subject to the following two

conditions: (1) this device may not cause

interference, and (2) this device must

accept any interference, including

interference that may cause undesired

operation of the device.

Privacy of communications may not be

ensured when using this telephone.

DIGITAL SECURITY CODE

Your SPP-206 has been assigned a

permanent and unique digital security

code out of possible 65,000 codes.

3EN

Table of contents

Getting Started

4 Read this first

5 Step 1: Checking the package

contents

6Step 2: Setting up the base phone

9 Step 3: Preparing the battery

pack

Basics

11 Making calls

12 Redialing

13 Receiving calls

Advanced Features

14 Speed dialing

14 Storing phone numbers on

the handset

15 Storing phone numbers on

the base phone

16 Making calls with speed

dialing on the handset

16 Making calls with speed

dialing on the base phone

17 Switching the phones during a

call

17 To switch from the base

phone to the handset

18 To switch from the handset

to the base phone

19 Talking between the handset and

the base phone (Intercom)

19 To talk from the handset to

the base phone

19 To talk from the base phone

to the handset

20 Transferring a call

20 To transfer from the base

phone to the handset

21 To transfer from the handset

to the base phone

22 Having a three-way conference

22 To join the phone

conversation

Additional

Information

23 Resetting the digital security code

24 Mounting the base phone on a

wall

25 Notes on power sources/

Maintenance

26 Troubleshooting

28 Specifications

29 Index

Getting Started

4EN

Read this first

Getting Started

Step 2 (page 6 to 8)

Next, you need to do three things

to set up the base phone, including

finding the best location for the

base phone.

Step 3 (page 9 to 10)

Finally, you need to insert the battery

pack into the handset and charge it for

more than 12 hours.

About the digital security code

This cordless telephone uses a digital security code to provide protection against

unintentional access to your base phone.

This security code blocks other cordless handsets to make calls through your base phone.

A random security code will be assigned automatically between your base phone and

handset when you charge the battery pack for the first time.

If you want to reset the digital security code, see page 23.

Base

phone

Handset

Step 1 (page 5)

First, unpack the phone and the supplied

accessories.

Before you use your phone, you must set it up. Here is a quick

way to set up your phone: Step 1, 2 and 3.

That's it!

Getting Started

5EN

Getting Started

Telephone line cords (2)

Step 1

Base phone

Rechargeable battery

pack (BP-T16)

AC power adaptor

(AC-T48)

Checking the package contents

Make sure you have received the following items in the package.

If anything is missing, contact your local Sony dealer.

Wall bracket/stand

for base phone

Handset

Getting Started

6EN

Step 2

Away from a microwave oven

Away from a personal

computer

Away from noise sources, such as a window by

a street with heavy traffic

Away from heat sources, such as radiators,

airducts, and sunlight

Away from excessive

moisture, extremely low

temperatures, dust,

mechanical vibration, or

shock

Away from

television sets and

other electronic

equipment

Away from another cordless

telephone

CAUTION: The cordless telephone operates at a frequency that may cause interference to

nearby TVs and VCRs; the base phone should not be placed near or on top of a

TV or VCR; and if interference is experienced, moving the cordless telephone

farther away from the TV or VCR will often reduce or eliminate the interference.

Near a central location

and on a level surface

Setting up the base phone

Do the following steps:

• Choose the best location

• Connect the base phone

• Choose the dialing mode

Choosing the best location

Where you place the base phone affects the reception quality of the

handset.

Getting Started

7EN

Getting Started

1Attach the wall bracket on the

bottom of the base phone as

illustrated to use it as a stand.

2Connect the telephone line cord

to the LINE jack, and to a

telephone outlet.

3Connect the AC power adaptor

to the DC IN 9V jack, and to an

AC outlet.

4Fully extend the antenna. Make

sure it points toward the ceiling.

Route the cord. 4

AC power adaptor

(supplied)

To LINE

To DC IN 9 V

Connecting the base phone

If you want to hang the base phone on the wall, see page 24.

Telephone line cord

(supplied)

continued

To AC outlet

To telephone outlet

Aligh the ¢

marks.

Getting Started

8EN

Notes

• Use only the supplied AC-T48 AC power adaptor.

Do not use any other AC power adaptor.

• Connect the AC power adaptor to a continuous power supply.

• Place the base phone close to the AC outlet so that you can easily

unplug the AC power adaptor.

Tips

• If your telephone outlet is not modular, contact your telephone service

company for assistance.

• To remove the wall bracket, press the upper tab.

Choosing the dialing mode

For the telephone to work properly, select an appropriate dialing mode

(tone or pulse).

Polarity of the plug

–

Step 2: Setting up the base phone (continued)

Modular

Depending on your dialing system, set the DIAL MODE switch as

follows:

If your dialing system is Set the switch to

Tone TONE

Pulse PULSE

If you are not sure of your dialing system

Make a trial call with the DIAL MODE switch set to TONE.

If the call connects, leave the switch as it is; otherwise, set to PULSE.

DIAL MODE switch

Getting Started

9EN

Getting Started

Preparing the battery pack

Insert the battery pack into the handset, then place the handset on the

base phone.

1Slide open the battery compartment

lid of the handset.

2Connect the battery connector with

correct polarity (black and red cords).

3Insert the battery pack. Then close the

lid.

4Place the handset on the base phone.

The CHARGE lamp lights up when

the handset is properly seated on the

charge terminals of the base phone.

Charge the battery pack for more than

12 hours so that the battery is fully

charged.

Step 3

continued

CHARGE lamp

Red

Black

Getting Started

10EN

Step 3: Preparing the battery pack (continued)

Battery duration

A fully charged battery pack lasts for about:

• 7 hours when you use the handset continuously.

• 14 days when the handset is in standby mode.

Battery life may vary depending on usage condition and ambient

temperature.

Notes

• The battery pack will gradually discharge over a long period of time, even if

not in use.

• The CHARGE lamp of the base phone is always lighted when the handset is

placed on the base phone, even if the battery pack has been fully charged.

• The battery works best when charged after several calls.

• If you leave the battery pack in the handset without charging it, the battery

pack will be completely discharged.

It may require several times of charging to recover to its full capacity.

When to purchase a new battery pack

If the battery lasts only a few minutes even after 12 hours of charging,

the usable life of the battery has expired and needs replacement.

Contact your local Sony authorized dealer or service center, and ask

for a Sony BP-T16 rechargeable battery pack.

Andere Handbücher für SPP-206

Inhaltsverzeichnis

Sprachen:

Andere Sony Schnurloses Telefon Handbücher

Sony

Sony SPP-114 Bedienungsanleitung

Sony

Sony SPP-SS965 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-933 - 900mhz Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-S9000 - Cordless Telephone Bedienungsanleitung

Sony

Sony PP-A2780 Bedienungsanleitung

Sony

Sony SPP-S9000 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-S9101 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-A900 Primary Bedienungsanleitung

Sony

Sony SPP-A968 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-N1023 Bedienungsanleitung

Sony

Sony SPP-ID971 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-SS960 - Cordless 900 Mhz Telephone Bedienungsanleitung

Sony

Sony SPP-A941 - Cordless Telephone With Answering... Kurzanleitung

Sony

Sony SPP-S9101 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-205 - 43-49 Mhz Cordless Phone Bedienungsanleitung

Sony

Sony SPP-N1025 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-A1070 - Caller Id Telephone Bedienungsanleitung

Sony

Sony SPP-A5000 Bedienungsanleitung

Sony

Sony SPP-A400 - Cordless Telephone With Answering... Bedienungsanleitung

Sony

Sony SPP-N1025 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-N1001 Bedienungsanleitung

Sony

Sony SPP-IM977 Bedienungsanleitung

Sony

Sony SPP-206 Bedienungsanleitung

Sony

Sony SPP-935 - 900 Mhz Cordless Phone Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung