Sony SPP-800 Bedienungsanleitung

MICROFILM

SPP-800/810/850/860

SERVICE MANUAL

CORDLESS TELEPHONE

SPECIFICATIONS

Taiwan Model

General

Frequency control Crystal-controlled PLL

Output mode FM, duplex

Operation channel 10 channels

Supplied accessories AC Power adaptor AC-T56 (1)

Telephone Line cords (1)

Rechargeable battery pack BP-T16 (1)

Directories (2 sheets)

Screw (2)

Handset

Power source Rechargeable battery pack BP-T16

Battery life Standby : Approx. 14 days

Talk : Approx. 6 hours

Dimensions Approx. 2 3/8x 8 x 2 3/8inches (w/h/d), antenna

excluded (Approx. 59 x 201 x 59mm)

Antenna : 4 3/8inches (110mm)

Mass Approx. 8.1 oz (Approx. 230g), battery included

Base unit

Power source DC 9V fromAC power adaptor

Battery charging time Approx. 12hours

Dimensions Approx. 5 7/8x 2 3/8x 9 inches (w/h/d), antenna

excluded (Approx. 148 x 58 x 233mm)

Antenna : 17 inches (430mm)

Mass Approx. 12.1 oz (Approx. 345g)

Design and specifications are subject to change without notice.

– 2 –

Specifications ........................................................................... 1

1. GENERAL

Location and Function of Controls .................................... 3

Setting up the Phone .......................................................... 4

Making and Receiving Calls .............................................. 4

Speed Dialing..................................................................... 5

Resetting the Digital Security Code................................... 5

Paging ................................................................................ 5

Maintenance ....................................................................... 5

Mounting Your Phone on the Wall ..................................... 5

2. DISASSEMBLY

2-1. Battery Case Lid Removal.......................................... 6

2-2. Cabinet (Rear) Removal ............................................. 6

2-3. Hand Main Board Removal ........................................ 6

3. TEST MODE ............................................................7

4. ELECTRICAL ADJUSTMENTS

4-1. Base Unit Section ..................................................... 12

4-2. Handset section......................................................... 16

5. DIAGRAMS

5-1. Explanation of IC Terminals..................................... 20

5-2. Block Diagrams (Base Unit Section)........................ 23

5-3. Block Diagrams (Handset Section) .......................... 25

5-4. Printed Wiring Boards (Base Unit Section).............. 27

5-5. Schematic Diagram (Base Unit Section) .................. 29

5-6. Schematic Diagram (Handset Section)..................... 32

5-7. Printed Wiring Boards (Handset Section) ................ 35

6. EXPLODED VIEWS

6-1. Handset Section ........................................................ 37

6-2. Base Unit Section ..................................................... 38

7. ELECTRICAL PARTS LIST ................................39

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK !OR DOTTED LINE

WITH MARK !ONTHE SCHEMATIC DIAGRAMS AND INTHE

PARTS LIST ARE CRITICALTO SAFE OPERATION.

REPLACE THESE COMPONENTS WITH SONY PARTSWHOSE

PART NUMBERS APPEAR AS SHOWN INTHIS MANUAL OR

IN SUPPLEMENTS PUBLISHED BY SONY.

Notes on chip component replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

TABLE OF CONTENTS

– 3 –

SECTION 1

GENERAL

LOCATION AND FUNCTION OF CONTROLS

1SPEED DAIAL

2TALK button

3TALK/BATT low lamp

4OFF button

5SPEAKER

6Helical antenna

7FLASH button

8Dialing keys

9CHANNEL button

!º REDIAL/PAUSE button

!¡ PGM

!™ Microphone

1Charging terminals

2Hang-up tab

3Telescopic antenna

4POWER/CHARGE/IN USE lamp

BASE UNIT

HANDSET

This section is extracted from

instruction manual.

5PAGE key

6LINE jack

7DIAL MODE switch

8DC IN 9V jack

– 4 –

– 5 –

– 6 –

SECTION 2

DISASSEMBLY

Note : Follow the disassembly procedure in the numerical order given.

2-1. BATTERY CASE LID REMOVAL

2-2. CABINET (REAR) REMOVAL

2-3. HAND MAIN BOARD REMOVAL

Battery case lid

Nickel cadmium battery (BP-T16)

Screws (2.6 x 8)

Cabinet (Rear

)

Screws (2.6 x 8)

Screw (2.6 x 12)

Connector (CN101)

Hand main board

Helical antenn

– 7 –

SECTION 3

TEST MODE

BASE UNIT

1. ManualTest Mode

1Set the [DIALMODE] switch to “ P ” (pulse).

2While pressing the [PAGE] key, switch on the power supply (Reset start).

3With the [PAGE] key, still held down, switch the [DIALMODE] switch “ P ” (pulse) n“ T ” (tone) n“ P ” (pulse).

4When you release the [PAGE] key, test mode starts.

5Frist dial “ 0 ” at 10 pps. Then ouput “ 1”, “ 4 ”, “ 8 ” and “ # ” with DTMF.

6Set to TX ON. Goes to external line state in 1 CH.

• How to Release theTest Mode

1Pull out the AC adapter and turn off the power

2. MachineTest Mode

1With one of the CH setting terminals in “ H ” input state, cause Reset of Power ON. Equipment enters machine test mode.

2Setting of CH according to logic input with CH setting terminal.

3ON/OFF of TX is according to the input logic of the Dial Mode terminal.

• How to Release theTest Mode

1Pull out the AC adapter and turn off the power.

2Remove the short plug and turn on the power again.

30 25 20 16

1510

IC501

TP62

TP61

TP64

TP106

TP65

TP63

TEST MODE terminal

Open : Normal

Short :Test mode

( )

1-661-831-

(21)

[BASE MAIN BOARD] (Component side)

– 8 –

2-1. Channel Setting

During startup in machine test mode, make the following channel settings by loading the terminal input data.

2-2. MachineTest Mode Input/Output

2-2-1. Input (Input ports for other than main tasks)

2-2-2. Output (Output ports for other than main tasks)

TEST 1 TEST 2 TEST 3 Operation with CHARGE LED Operation with TX ON

@ª @• @¶

L L L If RSSI (H) is, detected : Light ON If RSSI (H) is, detected : Light ON

L L H If RSSI (L) is, detected : Light ON If RSSI (L) is, detected : Light ON

L H L If TX LOCK is detected : Light OFF If TX LOCK is detected : Light OFF

L H H If RX LOCK is detected : Light OFF If RX LOCK is detected : Light OFF

H L L ––––––––––––––––– BEEP output

H L H ––––––––––––––––– ID CODE output

H H L If RING is detected : Light ON If RING is detected : Light ON

H H H If PAGE KEY is input : Light ON If PAGE KEY is input : Light ON

Pin No. @£ @¢ @∞ @§ RX EREQUENCY TX EREQUENCY

Channel M1 M2 M3 M4 (MHz) (MHz)

CH1 H L L L 43.720 48.760

CH2 L H L L 43.740 48.840

CH3 H H L L 43.820 48.860

CH4 L L H L 43.840 48.920

CH5 43.920 49.020

CH6 43.960 49.080

CH7 44.120 49.100

CH8 44.160 49.160

CH9 44.180 49.200

CH10 44.200 49.240

CH11 44.320 49.280

CH12 44.360 49.360

CH13 44.400 49.400

CH14 H L H L 44.460 49.460

CH15 L H H L 44.480 49.500

CH16 H H H L 46.610 49.670

CH17 L L L H 46.630 49.845

CH18 46.670 49.860

CH19 46.710 49.770

CH20 46.730 49.875

CH21 46.770 49.830

CH22 46.830 49.890

CH23 H L L H 46.870 49.930

CH24 L H L H 46.930 49.990

CH25 H H L H 46.970 49.970

TEST1 L L H H 43.780 48.800

TEST2 H L H H 43.890 48.970

TEST3 L H H H 46.800 49.910

TEST4 H H H H 46.900 49.950

Pin Name Pin No. Function Logic

CH TEST @£ – @§ Setting the CH (channel) Refer to channel setting

(M1–M4)

DIAL MODE !¶ Setting the TX ON/OFF H (T) ; OFF, L (P) : ON

Manual : Channel increment Incrementing of channels in order from 16 to 25.

PAGE !§ Machine : Dial data “ 5 ” is output to Key input with “ L ” input. The first time there is

DTMF/DP exchange output of “ 5 ” with DTMF.

Pin Name Pin No. Function H Logic L Logic

CHARGE DET !• State in section 2-2-1. Refer to 2-2-1.

– 9 –

HANDSET

1. ManualTest Mode

1Enter the test mode by pressing [0] key while pressing the [1] key and [TALK] when in idle condition.

(Key operation : [0] n[1] n[TALK] )

2The RINGER will ring for 500msec when the test mode is started.

3Measurement mode of consumption current. (42# state. Refer to 2-3).

4Use key input to carry out the various settings.

5Use port inputs to set output from LED terminals.

• How to Release theTest Mode

1Press the [0] , [0] and [#] key.

2Turn OFF the power. (Remove the battery and replace them)

2. MachineTest Mode

1When power on reset is applied while a H (high) is input to the TEST SW (TP43) terminal (IC501 $∞ pin), the RING (Level H,

500msec) sounds.

2Following that, at a timing in which the TEST SW terminal has “ H ” (High) input, there is output of “ L ” by the CH (Channel)

setting control terminal. Then there is PLLsetting to the CH which was read to with the CH setting terminal according to that “ L”

output.

3Set the TX setting to TX OFF.

4The channel is set by voice not by data.

5Use port inputs to set output from LED terminals

• How to Release theTest Mode

1Turn off the power.

2Remove the short plug and turn on the power.

TP36

D501

JR113

JR112

JR111

TP43

IC501

TEST MODE terminal

Open : Normal

Short :Test mode

( )

[HAND MAIN BOARD] (Component side)

– 10 –

2-2. MachineTest Mode Input/Output

2-2-1. Input (Input ports for other than main tasks)

2-1. Channel Setting

During startup in machine test mode, make the following channel settings by loading the terminal input data.

2-2-2. Output (Output ports for other than main tasks)

Pin Name Pin No. Function Logic

ROW 1 – ROW 5 @ª,Setting the CH (channel) Refer to channel setting

#¡ – #¢

TEST CH 1Control terminal for setting the CH (channel) H: OFF, L : ON

TEST SW $º Start up of test mode H : Start, L : No start

TESTACT $¢ During test mode, causes start of intermittent operation H : Intermittent start

with external input.

Pin No. #¢ #£ #™ #¡ @ª TX EREQUENCY RX EREQUENCY

Channel ROW 5 ROW 4 ROW 3 ROW 2 ROW 1 (MHz) (MHz)

CH1 H L L L L 43.720 48.760

CH2 H L L L H 43.740 48.840

CH3 H L L H L 43.820 48.860

CH4 H L L H H 43.840 48.920

CH5 H L H L L 43.920 49.020

CH6 H L H L H 43.960 49.080

CH7 H L H H L 44.120 49.100

CH8 H L H H H 44.160 49.160

CH9 H H L L L 44.180 49.200

CH10 H H L L H 44.200 49.240

CH11 H H L H L 44.320 49.280

CH12 H H L H H 44.360 49.360

CH13 H H H L L 44.400 49.400

CH14 H H H L H 44.460 49.460

CH15 H H H H L 44.480 49.500

CH16 L L H H L 44.610 49.670

CH17 L L H H H 44.630 49.845

CH18 L H L L L 44.670 49.860

CH19 L H L L H 44.710 49.770

CH20 L H L H L 44.730 49.875

CH21 L H L H H 44.770 49.830

CH22 L H H L L 44.830 49.890

CH23 L H H L H 44.870 49.930

CH24 L H H H L 44.930 49.990

CH25 L H H H H 44.970 49.970

TEST1 L L L H L 43.780 48.800

TEST2 L L L H H 43.890 48.970

TEST3 L L H L L 46.800 49.910

TEST4 L L H L H 46.900 49.950

Pin Name Pin No. Function H Logic L Logic

TALK LED $• Various input/output monitor output (default : RSSI(H) No detection Detection

detection).

KEY LED 2During test mode : All lights lit, However, does not include No light Light

(SPP-850/860 only) measurement of consumption current.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sony Schnurloses Telefon Handbücher

Sony

Sony SPP-A972 - Cordless Telephone With Answering... Bedienungsanleitung

Sony

Sony SPP-SS961 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-A5000 Bedienungsanleitung

Sony

Sony SPP-A940 - 900 Mhz Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-ID200 Bedienungsanleitung

Sony

Sony SPP-S9101 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-S2730 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-SS964 Bedienungsanleitung

Sony

Sony SPP-ID970 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-S2720 Bedienungsanleitung

Sony

Sony SPP-206 Bedienungsanleitung

Sony

Sony SPP-S9000 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-A941 - Cordless Telephone With Answering... Bedienungsanleitung

Sony

Sony SPP-S9101 - Cordless Telephone Kurzanleitung

Sony

Sony SPP-A973 - Cordless Telephone With Answering... Bedienungsanleitung

Sony

Sony SPP-68 Bedienungsanleitung

Sony

Sony SPP-ID975 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-ID975 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-N1000 Bedienungsanleitung

Sony

Sony SPP-SS960 - Cordless 900 Mhz Telephone Bedienungsanleitung

Sony

Sony SPP-A400 - Cordless Telephone With Answering... Bedienungsanleitung

Sony

Sony SPP-68 Bedienungsanleitung

Sony

Sony SPP-933 - 900mhz Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-N1020 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung