Sony DNE-1000 Bedienungsanleitung

DIGITAL NEWS EDITING WORKSTATION

DNE-1000

MAINTENANCE MANUAL Part 1

1st Edition

BKNE-1010

EDITING FADER PANEL

BKNE-1011

EDITING CONTROL PANEL

EXTENDED INPUT AND KEYER BOARD

BKNE-1030

VIDEO EFFECTS BOARD

BKNE-1040

3D/LIGHTING/TRAIL EFFECTS BOARD

BKNE-1041

OPERATING PROGRAM

BZNE-1010/1020

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen.Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien.Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

Attention-when the product is installed in Rack:

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

make sure that the rack does not overload the supply

circuit.

2. Providing protective earth

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

confirm that the outlet is provided with a suitable

protective earth connection.

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make

sure that the internal air ambient temperature of the

rack is within the specified limit of this product.

4. Prevention against achieving hazardous

condition due to uneven mechanical loading

When this product is installed in a rack, please make

sure that the rack does not achieve hazardous

condition due to uneven mechanical loading.

DNE-1000 Serial No.10001 and Higher

BKNE-1010 Serial No.10001 and Higher

BKNE-1011 Serial No.10001 and Higher

BKNE-1030 Serial No.10001 and Higher

BKNE-1040 Serial No.10001 and Higher

BKNE-1041 Serial No. 10001 and Higher

BZNE-1010 Serial No. 10001 and Higher

BZNE-1020 Serial No. 10001 and Higher

1(E)

DNE-1000

Table of Contents

Manual Structure

Purpose of this manual ........................................................................................ 4 (E)

Related manuals................................................................................................... 4 (E)

1. Installation

1-1. Operating Environment .........................................................................1-1 (E)

1-2. Power Supply ........................................................................................1-1 (E)

1-2-1. Power Specifications ............................................................1-1 (E)

1-2-2. Power Cord...........................................................................1-1 (E)

1-3. Connectors.............................................................................................1-2 (E)

1-3-1. DNE-1000 ............................................................................1-2 (E)

1-3-2. BKNE-1010..........................................................................1-2 (E)

1-3-3. BKNE-1011..........................................................................1-2 (E)

1-4. Input and Output Signals of Connectors ...............................................1-3 (E)

1-4-1. DNE-1000 ............................................................................1-3 (E)

1-4-2. BKNE-1010..........................................................................1-6 (E)

1-4-3. BKNE-1011..........................................................................1-8 (E)

1-5. Example of System Connection ............................................................1-9 (E)

1-5-1. Stand Alone System .............................................................1-9 (E)

1-5-2. Server System.....................................................................1-10 (E)

1-5-3. Server System (Fast Transfer)............................................1-11 (E)

1-6. Attachment of DNE-1000 ...................................................................1-12 (E)

1-6-1. External Dimensions ..........................................................1-12 (E)

1-6-2. Space for Attachment .........................................................1-13 (E)

1-6-3. Rack Mounting ...................................................................1-14 (E)

1-7. Attachment of Control Panel (BKNE-1010/1011)..............................1-16 (E)

1-7-1. External Dimensions ..........................................................1-16 (E)

1-7-2. Space for Attachment .........................................................1-17 (E)

1-7-3. Connection of Control Panel ..............................................1-18 (E)

1-7-4. Replacement of Key Tops ..................................................1-19 (E)

1-7-5. Adjustment of Operation Power for Fader Lever ..............1-19 (E)

1-8. Installation of Options.........................................................................1-20 (E)

1-8-1. Installation of Plug-in Boards ............................................1-20 (E)

1-8-2. Inserting/Pulling Out of Plug-in Boards ............................1-22 (E)

1-8-3. Installation of Optional Boards ..........................................1-22 (E)

1-9. Switch Settings on Boards and LEDs Description..............................1-24 (E)

1-9-1. DNE-1000 ..........................................................................1-24 (E)

1-9-2. BKNE-1010........................................................................1-28 (E)

1-9-3. BKNE-1011........................................................................1-28 (E)

1-10. Hard Reset (DNE-1000)......................................................................1-28 (E)

2(E) DNE-1000

1-11. Confirmation and Adjustment of

Secondary Power Supply Voltage.......................................................1-29 (E)

1-11-1. DNE-1000 ..........................................................................1-29 (E)

1-11-2. BKNE-1010........................................................................1-31 (E)

1-12. Initial Set-up of System.......................................................................1-31 (E)

2. Service Overview

2-1. DNE-1000 .............................................................................................2-1 (E)

2-1-1. Removal of Exterior Parts ....................................................2-1 (E)

2-1-2. Location of Main Parts .........................................................2-2 (E)

2-1-3. Capacitor for Data Backup ...................................................2-2 (E)

2-1-4. Spare Parts............................................................................2-2 (E)

2-2. BKNE-1010...........................................................................................2-3 (E)

2-2-1. Removal of Exterior Parts ....................................................2-3 (E)

2-2-2. Location of Main Parts .........................................................2-4 (E)

2-2-3. Installation and Removal of Boards .....................................2-4 (E)

2-2-4. Spare Parts............................................................................2-5 (E)

2-3. BKNE-1011...........................................................................................2-6 (E)

2-3-1. Removal of Exterior Parts ....................................................2-6 (E)

2-3-2. Location of Main Parts .........................................................2-7 (E)

2-3-3. Installation and Removal of Boards .....................................2-8 (E)

2-3-4. Spare Parts..........................................................................2-10 (E)

3. Replacement of Main Parts

3-1. DNE-1000 .............................................................................................3-1 (E)

3-1-1. Replacement of Power Unit .................................................3-1 (E)

3-1-2. Replacement of Fan on the Rear Panel ................................3-1 (E)

3-2. BKNE-1010...........................................................................................3-2 (E)

3-2-1. Replacement of Search Dial ................................................ 3-2 (E)

3-3. BKNE-1011...........................................................................................3-3 (E)

3-3-1. Replacement of Rotary Encoder ..........................................3-3 (E)

3-3-2. Replacement of Fader ..........................................................3-4 (E)

4. Trouble Shooting (BKNE-1010/1011)

4-1. Self Diagnostics Mode ..........................................................................4-1 (E)

4-1-1. Required Tools .....................................................................4-2 (E)

4-1-2. Positions of Knobs and Buttons on the Panel ......................4-3 (E)

4-1-3. Starting of Self Diagnostics Mode .......................................4-4 (E)

4-1-4. Procedures for Tests .............................................................4-4 (E)

4-1-5. Ending the Self Diagnostics Mode.......................................4-7 (E)

4-2. Trouble Shooting...................................................................................4-8 (E)

3(E)

DNE-1000

5. Cleaning

5-1. Front Panel ............................................................................................5-1 (E)

5-2. Fan.........................................................................................................5-1 (E)

6. Overall Block Diagrams

6-1. DNE-1000 ...................................................................................................6-2

6-2. BKNE-1010.................................................................................................6-4

6-3. BKNE-1011.................................................................................................6-6

4 (E) DNE-1000

Purpose of this manual This manual is the maintenance manual of the digital news editing workstation

DNE-1000 and the control panel BKNE-1010 and 1011.

This manual is intended for use by trained system and service engineers, and

describes the information of installation and the information on primary service.

Related manuals Besides this Maintenance Manual Part 1, the following manuals are available for

DNE-1000.

• Operation Manual (Supplied with DNE-1000.)

This manual explains the overview of DNE-1000 and optional boards, and the

system configuration examples.

Part number : 3-858-649-01

• Maintenance Manual Part 2 (Not supplied with DNE-1000.)

Volume 1

(Service Overview, Electrical Alignment, Spare parts and Semiconductor pin

assingnments)

Part number : 9-968-501-01

Volume 2

(Block diagrams, Board layouts and Schematic diagrams)

Part number : 9-968-502-01

This manual describes the information that premise the service based on parts.

If this manual is required, please contact to Sony’s service organization.

The part numbers of these manuals as of February, 1997 describe.

Manual Structure

1-1(E)

DNE-1000

Section 1

Installation

1-1. Operating Environment

Avoid placing or using this unit where it will be exposed to

greasy fumes, steam, dampness and dust environments.

If placing or using this unit in these environments, it may

cause a fire and an electric shock.

.The operating temperature is 5 dC to 40 dC.

Do not install this unit near heat sources.

.To prevent a temperature rise inside the unit, pay careful

attention to circulation of air in the place where the unit

is installed.

Do not block the ventilation holes on the outer cabinet.

1-2. Power Supply

1-2-1. Power Specifications

Power requirements: 100 to 240 V AC ±10%

50/60 Hz

Current consumption: 4.0 A maximum

(with all optional boards installed)

A switching regulator is used for the power supply of this

unit. The voltage within the range of 100 V to 240 V can

be used without changing the supply voltage.

As the inrush current at turn-on is the maximum 25 A, the

capacity of the AC power must be commensurate in it with

the inrush current of the maximum 25 A.

If the capacity of the AC power is not the adequately large,

the breaker of the AC power at the supply side will operate

or the unit will abnormal operate.

1-2-2. Power Cord

The power cord is not supplied with DNE-1000. Be sure to

use the power cord that is applicable to places in the world.

To avoid a fire or an electric shock, be sure to use the

designated power cord.

And do not damage to the power cord.

For the customer outside of the area as shown above,

please consult with local Sony’s sale/service office.

AC inlet

For the customer in the U.S.A. and Canada

Required Parts

DK-2401 (UC)

1Power Cord, 125 V 10 A (2.4 m)

2Plug Holder B (Black) : 2-990-242-01

AC inlet

For the customer in the United Kingdom

Required Parts

DK-2401 (EK)

1Power Cord, 250 V 10 A (2.4 m)

2Plug Holder B (Black) : 2-990-242-01

AC inlet

For the customer in the all European countries

except the United Kingdom

Required Parts

DK-2401 (AE)

1Power Cord, 250 V 10 A (2.4 m)

2Plug Holder B (Black) : 2-990-242-01

1-2(E) DNE-1000

1-3. Connectors

When connecting cables to various connectors on the rear

panel at the time of attaching or servicing, connect the

following connectors or their equivalents.

1-3-1. DNE-1000

Connector function Connector name and part

name on the rear panel number of matching cable

PRIMARY INPUT BNC coaxial connector plug

DIGITAL OUTPUT

WORD SYNC OUTPUT

REF IN

GPI D-sub 25-pin, Male

Connector 25-pin, Male

1-560-904-11

Junction Shell 25-pin

1-563-377-11

PANEL Included with DNE-1000.

GUI Transceiver Cable

1-559-701-11

Micro Transceiver

Allied Telesis

Centre COMTM (*1) MX10s

DEVICE CONTROL D-sub 9-pin, Male

Connector 9-pin, Male

1-560-651-00

Junction Shell 9-pin

1-561-749-00

RS232C D-sub 9-pin, Female

Connector 9-pin, Female

1-563-815-21

Junction Shell 9-pin

1-561-749-00

AUX INPUT XLR 3-pin, Male

REF TC IN 1-508-084-00 (*2)

PGM OUT XLR 3-pin, Female

MONITOR 1-508-083-00 (*3)

REF TC IN

1-3-2. BKNE-1010

Connector function Connector name and part

name on the rear panel number of matching cable

EDITOR Included with DNE-1000.

EDITOR D-sub 9-pin, Male

Connector 9-pin, Male

1-560-651-00

Junction Shell 9-pin

1-561-749-00

FADER PANEL Included with BKNE-1011.

1-3-3. BKNE-1011

Connector function Connector name and part

name on the rear panel number of the matching cable

CONTROL PANEL Included with BKNE-1011.

(*1) : Centre COM is a trademark of Allied Telesis Corporation.

(*2): Equivalent to CANNON XLR 3-12C.

(*3): Equivalent to CANNON XLR 3-11C.

1-3(E)

DNE-1000

1-4. Input and Output Signals of Connectors

The input and output signals of the connectors on the rear

panel are specified in the following table.

And refer to the following illustration for the pin positions

of the connectors.

1-4-1. DNE-1000

MONITOR : (XLR 3-pin, Female)

+4 dBm (600 Zat load), low impedance, balanced

REF TC IN : (XLR 3-pin, Male)

0.5 through 18 Vp-p, 10 KZ, balanced

AUX INPUT : AES/EBU Digital audio (XLR 3-pin, Male)

PGM OUT : AES/EBU Digital audio (XLR 3-pin, Female)

AES/EBU format stereo mode, balanced

PRIMARY INPUT : SDI Digital video (BNC)

DIGITAL OUTPUT: SDI Digital video (BNC)

Serial digital (270 Mbits/second)/SMPTE 259M/

ITU-R BT.656III

WORD SYNC OUTPUT : (BNC)

Word clock, TTL level (48.0 kHz)

REF IN : Analog video (BNC, roop through out)

Black burst or composite sync

0.3 Vp-p, 75 Z, sync negative

GPI

PANEL

RS232C

GUI

H (LOCAL DISK)

C (LOCAL DISK)

A (LOCAL DISK)

DEVICE CONTROL

AC IN

F (LOCAL DISK)

AUX INPUT PGM OUT MONITOR

42 3/4 R

1/2 L

REC TC IN

WORD SYNC

OUTPUT1

REF IN

PRIMARY INPUT

DIGITAL OUTPUT

IN5 IN1

IN2

IN3

IN4

IN6

IN7

IN8

EDIT PVW PGM

CAPTURE

D-sub 25-pin Female

D-sub 15-pin Female

D-sub 9-pin Female

D-sub 9-pin Male

25 GPI

PANEL

GUI

DEVICE CONTROL

RS232C

1-4(E) DNE-1000

1-4. Input and Output Signals of Connectors

(*1) <Controller> : indicates a controlling device.

(*2) <Device> : indicates a controlled device.

(*3) : Based on the Ethernet 10 BASE-5

(*4) : Based on the RS-232C

(*5) : Based on the RS-422A

GUI : Ethernet 10 BASE-5 (*3) (D-sub 15-pin Female)

Pin No. Signal name Function

1 GND Ground

2 ECD+Collision-detection (+)

3 ETX+Transmitted data (+)

4–– ––

5 ERX+Received data (+)

6 COMMON Common ground

7–– ––

8–– ––

9 ECD_Collision-detection (_)

10 ETX_Transmitted data (_)

11 –– ––

12 ERX_Received data (_)

13 +12 V Power supply +12 V

14 –– ––

15 –– ––

RS232C : RS-232C (*4) (D-sub 9-pin Male)

<Controller> (*1)

Pin No. Signal name Function

1–– ––

2 RXD Received data

3 TXD Transmitted data

4–– ––

5 GND Ground

6–– ––

7 RTS Request to send (Output)

8 CTS Clear to send (Input)

9–– ––

DEVICE CONTROL from A to J (**

*6) :

RS-422A(*5) (D-sub 9-pin Female)

<Device> (*2) from VTR, data servier and local strage

(MAV-500) etc..

Pin No. Signal name Function

1 GND Ground

2 CTLA RXA Received data (_)

3 CTLA TXB Transmitted data (+)

4 GND Ground

5–– ––

6 GND Ground

7 CTLA RXB Received data (+)

8 CTLA TXA Transmitted data (_)

9 GND Ground

(*6) : When BKNE-1030 (IF-609 board) is attached to

DNE-1000, it is possible to use the DEVICE

CONTROL from E to J.

PANEL : RS-422A (*5) (D-sub 15-pin Female)

<Device> (*2) from control panel BKNE-1010.

Pin No. Signal name Function

1 GND Ground

2 PANEL RXB Received data (+)

3 PANEL RXA Received data (_)

4 PANEL TXB Transmitted data (+)

5 PANEL TXA Transmitted data (_)

6–– ––

7–– ––

8 GND Ground

9 GND Ground

10 METER+Data for level meter +(*7)

11 +12 V Power supply +12 V

12 METER_Data for level meter _(*7)

13 +12 V Power supply +12 V

14 +12 V Power supply +12 V

15 GND Ground

(*7) :The meter signals of the pin numbers 10 and 12 are

used for BKNE-1011.

Andere Handbücher für DNE-1000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sony Desktop Handbücher

Sony

Sony MX Bedienungsanleitung

Sony

Sony Vaio PCV-RZ40C1B Bedienungsanleitung

Sony

Sony Vaio VGC-LT28E Bedienungsanleitung

Sony

Sony VAIO VGN-UX380FN Bedienungsanleitung

Sony

Sony PCV-R553DS - Vaio Digital Studio Desktop... Bedienungsanleitung

Sony

Sony VAIO VPCZ116GA Betriebsanleitung

Sony

Sony VGC-LS1 - Vaio All-in-one Desktop Computer Originalbetriebsanleitung

Sony

Sony PCV-RZ24G - Vaio Desktop Computer Bedienungsanleitung

Sony

Sony Vaio VPCZ2 Series Originalbetriebsanleitung

Sony

Sony PCV-RX460 Bedienungsanleitung

Sony

Sony PCV-RZ56G VAIO User Guide (primary manual) Bedienungsanleitung

Sony

Sony Vaio VGX-XL2A Originalbetriebsanleitung

Sony

Sony PCV-J150 - Vaio Desktop Computer Bedienungsanleitung

Sony

Sony VAIO MX PCV-MXS10 Bedienungsanleitung

Sony

Sony PCV-R553DS - Vaio Digital Studio Desktop... Bedienungsanleitung

Sony

Sony VPCL22K1E/B Bedienungsanleitung

Sony

Sony VGC-JS110J - Vaio All-in-one Desktop... Originalbetriebsanleitung

Sony

Sony PCV-RZ22G - Vaio Desktop Computer Bedienungsanleitung

Sony

Sony PCV-RX560 - Vaio Desktop Computer Bedienungsanleitung

Sony

Sony VPCJ111FX Originalbetriebsanleitung

Sony

Sony Vaio VGC-JS410F/S Originalbetriebsanleitung

Sony

Sony VAIO VGC-RA842G Bedienungsanleitung

Sony

Sony VAIO VGN-SZ700 Series Bedienungsanleitung

Sony

Sony VGN-N300 series Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

HP Z1 Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung