Sony FWD-50PX3 - 50" Plasma Panel Bedienungsanleitung
FLAT WIDE DISPLAY MONITOR
FWD-50PX3
PROTOCOL MANUAL (For Customer)
FWD-50PX3
Table of Contents
1. Communication Parameters ......................................................... 1
2. Pin Assignment..................................................................................... 1
3. Communication Data Format ....................................................... 1
4. General Function ................................................................................. 3
5. Analog Signal Detect Function ................................................... 9
6. Priority Signal Select Function ................................................. 10
7. Picture/Sound ...................................................................................... 14
8. Size/Shift ................................................................................................. 17
9. Status Enquiry..................................................................................... 20
10. User Reset.............................................................................................. 24
1
FWD-50PX3
1. Communication Parameters
Communication method RS-232C
Synchronous method Asynchronous
Baud rate 9600bps
Character length 8bit
Parity None
Start bit length 1bit
Stop bit length 1bit
Flow control None
2. Pin Assignment
12345
Monitor side (D-sub 9-pin)
_External view _
6789
12345
6789
Host side (D-sub 9-pin)
_External view _
Pin No. Function
1NC
2 TXD
3 RXD
4NC
5 GND
6NC
7NC
8NC
9NC
Pin No. Function
1NC
2 RXD
3 TXD
4NC
5GND
6NC
7NC
8NC
9NC
3. Communication Data Format
(a) Control message
No. Item Value
1 Header 0x8C: Control
2 Category 0xXX
3 Function 0xXX
4 Data1 (Length) 0xXX
5 Data2 (Data1) 0xXX
: : 0xXX
: : 0xXX
X DataX 0xXX
X+1 Check Sum 0xXX
*Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a
value exceeds 255 (1byte).
*Set the command interval to 500 ms or more when transmitting the
Control command continuously.
*Set the command interval to 500 ms or more when transmitting the same
command (Enquiry) after the Control command.
(b) Enquiry message
No. Item Value
1 Header 0x83: Enquiry
2 Category 0xXX
3 Function 0xXX
4 Data1 0xFF
5 Data2 0xFF
6 Check Sum 0xXX
*Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a
value exceeds 255 (1byte).
2FWD-50PX3
4Error answer
No. Item Value
1 Header 0xE0: Answer
2 Answer*0x00: No Function Error
0x01: Check Sum Error
0x02: Data Length Error
3 Check Sum 0xXX
*0x00: No Function Error Packet header,category or function code are
not included in this protocol.
0x01: Check Sum Error Check sum value or received packet is not
correct.
0x02: Data Length Error Packet is correctly received,but the data size
is over the upper limit.
(c) Answer message
1Control answer
No. Item Value
1 Header 0x70: Answer
2 Answer*0x00: Completed
0x01: Limit Over
0x02: Limit Under
0x03: Command Canceled
3 Check Sum 0xXX
*0x00: Completed Packet is correctly received and process
is also correctly completed.
0x01: Limit Over Packet is correctly received, but the data
value is over the upper limit.
0x02: Limit Under Packet is correctly received, but the data
value under the lower limit.
0x03: Command Canceled Packet is correctly received, but the data
value is not correct or the request cannot
be accepted in the current host state.
*Check Sum: Sum total of 1 to X. Lower one-byte data
is validated when a value exceeds 255
(1byte).
2Enquiry answer (Complete)
No. Item Value
1 Header 0x70: Answer
2 Answer 0x00: Completed
3 Return Data Size 0xXX
4 Return Data1 0xXX
: : 0xXX
: : 0xXX
X Return DataX 0xXX
X+1 Check Sum 0xXX
*0x00: Completed Packet is correctly received and process is also
correctly completed.
*Return Data: Returns the read value.
*Check Sum: Sum total of 1 to X. Lower one-byte data is validated
when a value exceeds 255 (1byte).
3Enquiry answer (Command cancel)
No. Item Value
1 Header 0x70: Answer
2 Answer 0x03: Command Canceled
3 Check Sum 0x73
0x03: Command Canceled Packet is correctly received, but the data
value is not correct or the request cannot
be accepted in the current host state.
3
FWD-50PX3
4. General Function
(a) Mode Control
Syntax Header Category Function Data1 Data2 Check Sum
Control 0x8C 0x00 Code Table (1-a) [a] 0x02 Code Table (1-a) [b] 0xXX
Enquiry 0x83 0xFF 0xFF 0xXX
Answer Header Answer Check Sum
Control 0x70 0x00 0x70 Completed
0x70 0x01 0x71 Limit Over
0x70 0x02 0x72 Limit Under
0x70 0x03 0x73 Command Canceled
Answer Header Answer Return to Data Size Return Data1 Check Sum
Enquiry 0x70 0x00 0x02 Code Table (1-a) [b] 0xXX Completed
Code Table (1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x00 Power 0x00 OFF Yes Yes Enable Enable
0x01 ON
0x01 Input Select*40x08 INPUT1 RGB (Analog) Yes Yes Disable Enable
0x09 INPUT1 YUV (Analog)
0x0C OPTION1 VIDEO
0x0D OPTION1 S-VIDEO
0x0E OPTION1 RGB
0x0F OPTION1 COMPONENT
0x10 OPTION2 VIDEO
0x11 OPTION2 S-VIDEO
0x12 OPTION2 RGB
0x13 OPTION2 COMPONENT
0x20 Input1 DVI
0x84 Option1 Digital1
0x85 Option1 Digital2
0x02 Force Status Display 0x00 ON Yes Yes Disable Enable
0x01 OFF
0x03 Audio Mute 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x04 Auto Status Display 0x00 ON Yes Yes Enable Enable
0x01 OFF (Continued)
4FWD-50PX3
Code Table (1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x06 Color System 0x00 Auto Yes Yes Disable Enable
0x01 NTSC
0x02 NTSC4.43
0x03 PAL
0x05 PAL-M
0x06 PAL-N
0x07 PAL60
0x0B Picture Inversion 0x00 OFF Yes Yes Disable Enable
0x01 Auto
0x02 On
0x0C Picture Orbit 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x0D Orbit Range 0x00 Small Yes Yes Disable Enable
0x01 Middle
0x02 Large
0x0E Orbit Cycle 0x00 Speed1 (10 sec ) Yes Yes Disable Enable
0x01 Speed2 (30 sec)
0x02 Speed3 (1 min )
0x03 Speed4 (5 min )
0x0F Language 0x00 Japanese Yes Yes Disable Enable
0x01 English
0x02 Deutsch
0x03 Français
0x04 Español
0x05 Italiano
0x10 Index Number 0x01-0xFF Yes Yes Disable Enable
0x12 Standby Power 0x00 Standard Yes Yes Disable Enable
0x01 Low
0x13 ECO Mode 0x00 Off Yes Yes Disable Enable
(Power Saving) 0x01 ECO High
0x02 ECO Low
0x14 Speaker Out 0x00 ON Yes Yes Disable Enable
0x01 OFF
0x18 Sync Mode 0x00 H/Comp Yes Yes Disable Enable
0x01 Video
0x1B Clock Display 0x00 OFF Yes Yes Disable Enable
0x01 ON (Continued)
5
FWD-50PX3
Code Table (1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x24 Input Detect 0x00 FW12 (HD15) No Yes Disable Enable
(Option1) 0x01 FW10 (VIDEO, S-VIDEO) BNC
0x02 FW11 (BNC)
0x03 Reserved
0x04 FW31/32
0x05 FW50 (RGB)
0x06 FW20 (UART +CTRL-S)
0x07 FW13 (COMPONENT) RCA
0x08 FW15 (HDMI x2)
0x09 FW16 (Digital x1)
0x0A Reserved
0x0B Reserved
0x0C Reserved
0x0D Reserved
0x0E Reserved
0x0F Not Connect
0x25 Input Detect 0x00 FW12 (HD15) No Yes Disable Enable
(Option2) 0x01 FW10 (VIDEO, S-VIDEO) BNC
0x02 FW11 (BNC)
0x03 Reserved
0x04 FW31/32
0x05 FW50 (RGB)
0x06 FW20 (UART +CTRL-S)
0x07 FW13 (COMPONENT) RCA
0x08 FW15 (HDMI x 2)
0x09 FW16 (Digital x 1)
0x0A Reserved
0x0B Reserved
0x0C Reserved
0x0D Reserved
0x0E Reserved
0x0F Not Connect
0x26 Auto Shut OFF 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x27 Auto Screen Adjust 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x30 PAP 0x00 OFF Yes Yes Disable Enable
0x01 P&P
0x02 PinP (Continued)
6FWD-50PX3
Code Table (1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x31 Active Picture 0x00 Left (P&P)/Main (PinP) Yes Yes Disable Enable
0x01 Right (P&P)/Sub (PinP)
0x02 Swap
0x32 Picture Size (P&P) 0x00-0x0E Yes Yes Disable Enable
0x33 Sub Picture Size 0x00 Large Yes Yes Disable Enable
(PinP) 0x01 Small
0x34 Picture Position 0x00 Position1 Yes Yes Disable Enable
(PinP) 0x01 Position2
0x02 Position3
0x03 Position4
0x35 PAP Input Detect 0x08 INPUT1 RGB (Analog) No Yes Disable Enable
(Left/Main) 0x09 INPUT1 YUV (Analog)
0x0C OPTION1 VIDEO
0x0D OPTION1 S-VIDEO
0x0E OPTION1 RGB
0x0F OPTION1 COMPONENT
0x10 OPTION2 VIDEO
0x11 OPTION2 S-VIDEO
0x12 OPTION2 RGB
0x13 OPTION2 COMPONENT
0x20 INPUT1 DVI
0x84 Option1 Digital1
0x85 Option1 Digital2
0x36 PAP Input Detect 0x08 INPUT1 RGB (Analog) No Yes Disable Enable
(Right/Sub) 0x09 INPUT1 YUV (Analog)
0x0C OPTION1 VIDEO
0x0D OPTION1 S-VIDEO
0x0E OPTION1 RGB
0x0F OPTION1 COMPONENT
0x10 OPTION2 VIDEO
0x11 OPTION2 S-VIDEO
0x12 OPTION2 RGB
0x13 OPTION2 COMPONENT
0x20 INPUT1 DVI
0x84 Option1 Digital1
0x85 Option1 Digital2
0x40 All White 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x41 BackGround 0x00 Gray Yes Yes Disable Enable
0x01 Dark Gray
0x02 Black (Continued)
7
FWD-50PX3
Code Table (1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x44 Logo Illumination & 0x00 Logo Off Yes Yes Enable Enable
Status LED 0x01 Logo On (Low)
0x02 Logo On (High)
0x04 LED Off
0x05 LED On
0x45 Control Mode 0x00 Main +Remocon Yes Yes Disable Enable
0x01 Main
0x02 Remocon
0x03 All Off
0x04 Limited*5
0x46 On Off Timer Mode 0x00 Every Day (Repeat) Yes Yes Enable Enable
0x01 Day Of Week
0x47 On Timer Enable bit0 Sunday 1: Enable, 0: Disable Yes Yes Enable Enable
bit1 Monday 1: Enable, 0: Disable
bit2 Tuesday 1: Enable, 0: Disable
bit3 Wednesday 1: Enable, 0: Disable
bit4 Thursday 1: Enable, 0: Disable
bit5 Friday 1: Enable, 0: Disable
bit6 Saturday 1: Enable, 0: Disable
bit7 Every day 1: Enable, 0: Disable
0x48 Off Timer Enable bit0 Sunday 1: Enable, 0: Disable Yes Yes Enable Enable
bit1 Monday 1: Enable, 0: Disable
bit2 Tuesday 1: Enable, 0: Disable
bit3 Wednesday 1: Enable, 0: Disable
bit4 Thursday 1: Enable, 0: Disable
bit5 Friday 1: Enable, 0: Disable
bit6 Saturday 1: Enable, 0: Disable
bit7 Every day 1: Enable, 0: Disable
0x49 Auto Dimmer 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x65 IP Setting Mode 0x00 DHCP Yes Yes Enable Enable
0x01 Manual
0x02 Speed
0x66 IP Setting Execute 0x00 No No Yes Enable Enable
0x01 Yes
0X02 NVR Reset (Continued)
8FWD-50PX3
Code Table (1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x67 IP Setting Result 0x00 Done Yes No Enable Enable
0x01 Error 1 (UART Commu.)
0x02 Error 2 (Duplication)
0x03 Error 3 (IP Add Setting)
0x04 Error 4 (GW Add setting)
0x05 Error 5 (DNS1 Setting)
0x06 Error 6 (DNS2 Setting)
0x07 Error 7 (Sbnt Msk Setting)
0x68 Speed Setting 0x00 100Mbps/Full Duplex Yes Yes Enable Enable
0x01 100Mbps/Half Duplex
0x02 10Mbps/Full Duplex
0x03 10Mbps/Half Duplex
0x04 Auto
0x70 Input Skip bit0 HD15 Yes Yes Disable Enable
bit1 DVI
bit2 Reserved
bit3 Reserved
bit4 Reserved
bit5 Reserved
bit6 Reserved
bit7 Reserved
0x71 Default Input 0x00 Last Memory Yes Yes Enable Enable
0x01 Option1
0x72 Input Detect 0x00 FW12 (HD15) No Yes Disable Enable
(Option3)*30x01 FW10 (VIDEO, S-VIDEO) BNC
0x02 FW11 (BNC)
0x03 Reserved
0x04 FW31/32
0x05 FW50 (RGB)
0x06 FW20 (UART +CTRL-S)
0x07 FW13 (COMPONENT) RCA
0x08 FW15 (HDMI x 2)
0x09 FW16 (Digital x 1)
0x0A Reserved
0x0B Reserved
0x0C Reserved
0x0D Reserved
0x0E Reserved
0x0F Not Connect (Continued)
Andere Handbücher für FWD-50PX3 - 50" Plasma Panel
3
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Sony Flachbildfernseher Handbücher
Sony
Sony Wega KE-P37XS1 Bedienungsanleitung
Sony
Sony WEGA KE-42MR1 Bedienungsanleitung
Sony
Sony KDL-46VL130 Bedienungsanleitung
Sony
Sony KDE-50XS955 - 50" Flat Panel Color Tv Bedienungsanleitung
Sony
Sony XBR-55X900A Benutzerhandbuch
Sony
Sony Bravia KLV-V26A10E Bedienungsanleitung
Sony
Sony SS-SP50FW Bedienungsanleitung
Sony
Sony Bravia KDL-19M4000 Bedienungsanleitung
Sony
Sony WEGA KE-42M1 Bedienungsanleitung
Sony
Sony KZ-32TS1U Bedienungsanleitung
Sony
Sony KDL-32V5800 Bedienungsanleitung
Sony
Sony WEGA KLV-30HR3 Bedienungsanleitung
Sony
Sony KDL-40EX500 - Bravia Ex Series Lcd... Bedienungsanleitung
Sony
Sony BRAVIA KDL-V40A11E Bedienungsanleitung
Sony
Sony bravia X series Bedienungsanleitung
Sony
Sony KLV-26NX400 Bedienungsanleitung
Sony
Sony PlasmaPro PFM 42X1 Bedienungsanleitung
Sony
Sony KDL-32XBR950 - 32" Flat Panel Lcd Wega™ Xbr... Bedienungsanleitung
Sony
Sony KDL-32S2800 Bedienungsanleitung
Sony
Sony BRAVIA 4-187-903-11(1) Bedienungsanleitung
