Sony MDR-RF930 Bedienungsanleitung

MICROFILM

SERVICE MANUAL

WIRELESS STEREO HEADPHONES

US Model

Canadian Model

SPECIFICATIONS

MDR-RF930

MDR-RF930 is headphones

in MDR-RF930K.

Notes on chip component replacement

•Never reuse a disconnected chip component.

•Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

Ver 1.0 1998. 06

– 2 –

SECTION 1

GENERAL

This section is extracted from

instruction manual.

– 3 –

HOUSING (R) ASSY, HANGER (R)

two screws

(P2

screw

(B1.7

ear pad

driver ( L-CH )

housing (L) assy

ball shaft holder

screw

(P2

battery cover

hanger (L)

two screws

(P2

two screws

(P2

10)

ball shaft holder

housing (R) assy

screw

(P 2

10)

hanger (R)

screw

(B1.7

ear pad

driver (R-CH)

• This set can be disassembled in the order shown below.

SECTION 2

DISASSEMBLY

HOUSING (L) ASSY, HANGER (L)

HOUSING (R) ASSY, HANGER (R)

BATTERY CASE

RX BOARD

SET

Note: Follow the disassembly procedure in the numerical order given.

HOUSING (L) ASSY, HANGER (L)

– 4 –

RX BOARD

two head bands

suspender assy

two screws

(P2

10)

battery cas

tension spring

push (1 key) SWITCH

two head band

suspender assy

RX board

RX shield plate

tension spring

two screws (B1.7

BATTERY CASE

– 5 –

Note:

1. The adjustments should be performed in the order given.

2. The transmitter (TMR-RF930) already checked and adjusted should be used.

3-1. Receiving Frequency Check and Adjustment

Preparation:

Procedure:

1. Set the channel of the transmitter to CH2.

2. Turn OFF the noise filter switch on the transmitter.

3. Enter 1 kHz 316 mVrms signal only to the Lch on the transmitter.

4. Place the transmitter away from the headphone (MDR-RF930) more than 5 m.

5. Set the volume control (RV301) on the RX-BASE board to the minimum position.

6. Set the tuning control (RV302) on the RX-BASE board to the center position.

7. Connect a DC voltmeter and an oscilloscope between IC301 pin @¡ and ground on the RX-BASE board.

8. After confirming that demodulated 1 kHz waveform (about 13 mV) appears on the oscilloscope, check that the DC voltmeter indicates

DC1 V to 1.2 V.

9. If demodulated 1 kHz waveform does not appear on the oscilloscope, or if the voltage is out of the specified value, adjust the air-core

coil (L301) on the RX-BASE board so that the demodulated 1 kHz waveform appears on the oscilloscope, and under this condition,

adjust finely the air-core coil (L301) so that the DC voltmeter indicates DC1.1 V.

10. Finally, check that signals are received when the channel is changed over to CH1/CH3 on the transmitter, then when the tuning control

(RV302) on the RX-BASE board is rotated.

Adjustment Location: RX-BASE board (See page 9.)

SECTION 3

ELECTRICAL ADJUSTMENTS

AF OSC

ATT

AUDIO IN (Lch)

1 kHz 316mVrms

600

Ω

Trans-

mitter Head-

phones

–+

–

TMR-RF930 5 m MDR-RF93

–

oscilloscope

DC voltmeter

[RX-BASE board] – Conductor Side –

– 6 –

3-2. Degree of Modulation of Main Carrier (L + R) Check and Adjustment

Preparation:

Procedure:

1. Set the channel of the transmitter to CH2.

2. Turn OFF the noise filter switch on the transmitter.

3. Enter 1 kHz 316 mVrms signal only to the Lch on the transmitter.

4. Set the volume control (RV301) on the RX-BASE board to the minimum position.

5. Connect an AC voltmeter and an oscilloscope between IC 301 pin @¡ and ground on the RX-BASE board.

6. Rotating the tuning control (RV302) on the RX-BASE board, receive signals.

7. After confirming that demodulated 1 kHz waveform appears on the oscilloscope, check that theAC voltmeter indicates 12 mVrms to

15 mVrms.

8. If out of the specified value, rotate RV404 on the TX-BASE board in the transmitter (TMR-RF930) so as to attain 13.5 mVrms.

Adjustment Location: TX-BASE board in the transmitter (TMR-RF930) (See page 8.)

AF OSC

ATT

AUDIO IN (Lch)

1 kHz 316 mVrms

600

Ω

Trans-

mitter Head-

phones

–+

–

TMR-RF930 MDR-RF93

–

oscilloscope

AC voltmeter

[RX-BASE board] – Conductor Side –

– 7 –

3-3. Separation Check and Adjustment

Preparation:

Procedure:

1. Set the channel of the transmitter to CH2.

2. Turn OFF the noise filter switch on the transmitter.

3. Enter 1 kHz 316 mVrms signal only to the Lch on the transmitter.

4. Connect an AC voltmeter and an oscilloscope to the Lch speaker output (both ends of MDD01) on the RX-BASE board.

5. Rotating the tuning control (RV302) on the RX-BASE board, receive signals.

6. Adjust the volume control (RV301) on the RX-BASE board so that the Lch speaker output (both ends of MDD01) on the RX-BASE

board becomes 155 mVrms.

7. Connect an AC voltmeter and oscilloscope to the Rch speaker output (both ends of MDD02) and measure voltage.

8. Check that a difference in speaker output level between Lch and Rch (i. e., separation) is over 20 dB. If not over 20 dB, rotate RV303

on the RX-BASE board to minimize the Rch output, then reconfirm that a difference in speaker output level between Lch and Rch is

over 20 dB.

9. Enter 1kHz 316 mVrms signal only to the Rch on the transmitter.

10. Adjust the volume control (RV301) on the RX-BASE board so that the Rch speaker output (voltage across MDD02) on the RX-BASE

board become 155 mVrms.

11. Connect an AC voltmeter and oscilloscope to the Lch speaker output (both ends of MDD01) and measure voltage.

12. Check that a difference in speaker output level between Lch and Rch (i.e., separation) is over 20 dB.

Adjustment Location: RX-BASE board (See page 9.)

AF OSC

ATT

AUDIO IN (Lch or Rch)

1 kHz 316 mVrms

600

Ω

Trans-

mitter Head-

phones

–+

–

TMR-RF930 MDR-RF93

–

oscilloscope

AC voltmeter

[RX-BASE board] – Conductor Side –

– 8 –

RV404

Degree of

Modulation of

Main Carrier (L + R)

Adjustment

NOISE FILTER

OFF

J402

(Rch) J403

(Lch)

S402

CHANNEL

CH1

CH2

CH3

S401

[TX-BASE board] – Component Side –

Adjustment Location:

Transmitter (TMR-RF930)

– 9 –

Headphone (MDR-RF930)

L301

Receiving Frequency

Adjustment

RV301

VOL

RV302

TUNING

MAX

MIN

[RX-BASE board] – Component Side –

IC301

RV303

Separation Adjustment

[RX-BASE board] – Conductor Side –

– 10 –

POWER

SWITCH MUTE

BIAS

AMP

5 6

10 MUTE

R-OUT

GND

L-OUT

VCC

PWR

R-IN

GND

L-IN

REG

SECTION 4

DIAGRAMS

• IC Block Diagrams

IC301 CXA1611N-T4

IC302 LA4533M

Inhaltsverzeichnis

Andere Sony Kopfhörer Handbücher

Sony

Sony MDR-NC8 Bedienungsanleitung

Sony

Sony MDR-ZX300IP Bedienungsanleitung

Sony

Sony Smart Wireless Headset pro Bedienungsanleitung

Sony

Sony MDR-EX310LP Bedienungsanleitung

Sony

Sony NOISE CANCELLING MDR-NC5 Bedienungsanleitung

Sony

Sony MDR-NC300D Bedienungsanleitung

Sony

Sony MDR-AS20J Bedienungsanleitung

Sony

Sony MDR-EX80LP Bedienungsanleitung

Sony

Sony MDR V700DJ Bedienungsanleitung

Sony

Sony MDRDS1000 - Digital Surround Sound Headphone... Bedienungsanleitung

Sony

Sony MDR-ZX300 Bedienungsanleitung

Sony

Sony MDR-AS35W - Veritical In The Ear Headphones Bedienungsanleitung

Sony

Sony MDR-XB1000 Bedienungsanleitung

Sony

Sony MDR-XB20EX Bedienungsanleitung

Sony

Sony MDR-RF970R Bedienungsanleitung

Sony

Sony MDR-EX57LP/BLK Bedienungsanleitung

Sony

Sony MDR-EX75/SLV Bedienungsanleitung

Sony

Sony MDR-Z7 Bedienungsanleitung

Sony

Sony MDR-RF940RK Bedienungsanleitung

Sony

Sony WALKMAN SRF-HM33 Bedienungsanleitung

Sony

Sony MDR-DS6500 Bedienungsanleitung

Sony

Sony MDR V500DJ Bedienungsanleitung

Sony

Sony MDR-E10LP - Stereo Headphones Gebrauchs- und Wartungshandbuch

Sony

Sony MDR-RF915RK Bedienungsanleitung

Beliebte Kopfhörer Handbücher anderer Marken

AUSounds

AUSounds AU-Stream Bedienungsanleitung

ENERGY SISTEM

ENERGY SISTEM Style 7 Bedienungsanleitung

Philips

Philips SHE3622 Bedienungsanleitung

Insignia

Insignia NS-CAHBTSPORT Bedienungsanleitung

Movie Vision

Movie Vision HP-400 Bedienungsanleitung

MobiFren

MobiFren SM Pro Bedienungsanleitung

Motorola solutions

Motorola solutions PMLN8120 Bedienungsanleitung

Jaybird

Jaybird freedom Installationsanleitung

HiFuture

HiFuture Tidy Buds Pro Bedienungsanleitung

Creative

Creative CB2530 Bedienungsanleitung

Renkforce

Renkforce RF FTVK-100 Bedienungsanleitung

Philips

Philips SHQ3000 Bedienungsanleitung

Sennheiser

Sennheiser 500371 Bedienungsanleitung

Califone

Califone 2924AV Bedienungsanleitung

Philips

Philips EARGEAR HE205 Series Bedienungsanleitung

Technics

Technics EAH-AZ80 Bedienungsanleitung

Bose

Bose On-Ear Headphone Gebrauchs- und Wartungshandbuch

Aluratek

Aluratek ABH02F Bedienungsanleitung