Sony CCB-WD1 Bedienungsanleitung

CCB-WD1

4-735-433-11(1)

CCB-WD1

4-735-433-11(1)

C:\4735433111\4735433111CCBWD1CEE\00COV-CCBWD1CEE\000COV.indd

DTP data saved: 2017/11/10 11:17

PDF file created: 2017/11/10 16:40

Camera Control Box

Instruction Manual

CCB-WD1

4-735-433-11(1)

C:\4735433111\4735433111CCBWD1CEE\01GB-CCBWD1CEE\01GB.indd

DTP data saved: 2017/11/29 16:03

PDF file created: 2017/11/29 16:09

English

WARNING

To reduce fire or shock hazard,

do not expose the unit to rain or

moisture.

IMPORTANT SAFETY

INSTRUCTIONS

-SAVE THESE

INSTRUCTIONS

DANGER

TO REDUCE THE RISK

OF FIRE OR ELECTRIC

SHOCK, CAREFULLY

FOLLOW THESE

INSTRUCTIONS

If the shape of the plug does

not fit the power outlet, use an

attachment plug adaptor of the

proper configuration for the power

outlet.

Use a nearby wall outlet (wall

socket) when using the AC

Adaptor/Battery Charger. If any

malfunction occurs, disconnect

the plug from the wall outlet (wall

socket) immediately to disconnect

from the power source.

If you use the product with a

charge lamp, note that the product

is not disconnected from the

power source even when the lamp

turns off.

CAUTION

For safety, do not connect the

connector for peripheral device

wiring that might have excessive

voltage to LAN terminal. Follow

the instructions for LAN terminal.

Power Cord

For the customers in the UK,

Ireland, Malta, Cyprus and Saudi

Arabia

Use the power cord (A). For safety

reasons, the power cord (B) is not

intended for above countries/

regions and shall therefore not be

used there.

For the customers in other EU

countries/regions

Use the power cord (B).

(A) (B)

LAN cable

Use a Category 5e or higher

Shielded Twisted Pair (STP) cable

with high shielding performance.

CCB-WD1

4-735-433-11(1)

C:\4735433111\4735433111CCBWD1CEE\01GB-CCBWD1CEE\01GB.indd

DTP data saved: 2017/11/29 16:03

PDF file created: 2017/11/29 16:09

For Customers in the U.S.A.

For question regarding your

product or for the Sony Service

Center nearest you, call 1-800-222-

SONY (7669).

Declaration of Conformity

Trade Name: SONY

Model No.: CCB-WD1

Responsible Party: Sony

Electronics Inc.

Address: 16535 Via Esprillo, San

Diego, CA 92127 U.S.A.

Telephone Number: 858-942-2230

This device complies with part

15 of the FCC rules. Operation

is subject to the following two

conditions: (1)This device may not

cause harmful interference, and

(2)this device must accept any

interference received, including

interference that may cause

undesired operation.

For Customers in Canada

CAN ICES-3 B/NMB-3 B

Notes on using

your product

• Refer to the Sony website for the

compatible models.

• Along with this manual, refer to

the Help Guide (page 12) of this

product and the instruction manual

of your camera.

Notes on handling the product

• This product is neither dust-proof,

nor splash-proof, nor water-proof.

• Do not leave the product or

the supplied accessories within

the reach of infants. They may

be accidentally swallowed. If

this occurs, consult a doctor

immediately.

On the data specifications

described in this manual

The data on performance and

specifications are defined under

the following conditions, except

as described in this manual: at an

ordinary ambient temperature of

25ºC (77°F).

CCB-WD1

4-735-433-11(1)

C:\4735433111\4735433111CCBWD1CEE\01GB-CCBWD1CEE\01GB.indd

DTP data saved: 2017/11/29 16:03

PDF file created: 2017/11/29 16:09

Notes to avoid access by

unintended third parties

Depending on the environment of

use, unintended third parties may

access your network. Only connect

this product to networked devices

managed by you. Connection

to other networked devices is

performed at your own risk. This

product may be accessed without

authorization and the contents of

communications may be intercepted.

Notes on discarding this product,

transferring it to others, or

returning a rented product

To prevent your data from being

leaked, execute the “Initialize”

function by following the procedure

below before you discard the

product, transfer it to others, or

return a rented product.

1 Connect the product to a

computer (page10).

2 Connect the product to the

AC Adaptor, and then turn the

product on (page11).

3 Launch a web browser on the

computer, and then execute the

“Initialize” function (page12).

• Initialization may take a long time.

Connect the product to a stable

power source so that it does not

turn off partway through.

• Set the MASTER/CLIENT switch

on the product as described on

page9.

Checking the

product and the

supplied items

The number in parentheses

indicates the number of pieces.

•Camera control box (1)

•Multi terminal connecting cable

(S) (1)

•Multi terminal connecting cable

(L) (1)

Two cables with different

lengths are supplied.

•Micro USB cable (1)

•AC Adaptor (1)

The shape of the AC Adaptor

may differ depending on the

country/region.

•Power cord (mains lead) (1)*

(supplied in some countries/

regions)

* Multiple power cords may be

supplied with this equipment.

Use the appropriate one that

matches your country/region.

See page2.

•Cable protector (1)

•Set of printed documentation

CCB-WD1

4-735-433-11(1)

C:\4735433111\4735433111CCBWD1CEE\01GB-CCBWD1CEE\01GB.indd

DTP data saved: 2017/11/29 16:03

PDF file created: 2017/11/29 16:09

Identifying parts

ON/OFF (Power) switch

This switch turns the power on

or off.

MASTER/CLIENT (Master/

Client) switch

Set this switch to “MASTER”

for one of the camera control

boxes, and to “CLIENT” for the

others.

Access lamp

Micro USB connector

Use this connector to connect

the product to the AC Adaptor

(supplied).

Multi terminal

Use this terminal to connect

the product to a camera.

Tripod socket hole

Use a tripod with a screw less

than 5.5mm (7/32inches)

long. Otherwise, you cannot

firmly secure the product, and

damage to the product may

occur.

Power lamp

LAN terminal

Use this terminal to connect

the product to a computer or a

switching hub.

CCB-WD1

4-735-433-11(1)

C:\4735433111\4735433111CCBWD1CEE\01GB-CCBWD1CEE\01GB.indd

DTP data saved: 2017/11/29 16:03

PDF file created: 2017/11/29 16:09

Connecting to a camera and a computer

Connect this product to a camera and a computer to operate the camera

from the computer.

You can operate multiple cameras at once from a single computer by

connecting them as illustrated below.

Set the MASTER/CLIENT switch on one of the products (camera control

boxes) to “MASTER.” Then, set the MASTER/CLIENT switches on the others

to “CLIENT.”

Conceptual diagram

DSC-RX0 Camera control box

Switching hub Computer

Note

• You can connect one camera to this product. To use multiple cameras, you

must connect each camera to a separate camera control box.

• It is recommended that you use 1000BASE-T switching hubs and LAN cables

rated as category 5e or higher.

CCB-WD1

4-735-433-11(1)

C:\4735433111\4735433111CCBWD1CEE\01GB-CCBWD1CEE\01GB.indd

DTP data saved: 2017/11/29 16:03

PDF file created: 2017/11/29 16:09

Cable protector

Use the cable protector to prevent the cables from being disconnected.

Run all the cables through the cable protector, and then connect the

cables to the product.

Attach the cable protector

to the product so that it

aligns with the shape of the

connector compartment,

and then secure the cable

protector by tightening the

two attachment screws.

Attachment screws

Secure the cables with the

fixing dial.

Fixing dial

CCB-WD1

4-735-433-11(1)

C:\4735433111\4735433111CCBWD1CEE\01GB-CCBWD1CEE\01GB.indd

DTP data saved: 2017/11/29 16:03

PDF file created: 2017/11/29 16:09

Connecting the product to a camera

Connect the product to the camera using the multi terminal connecting

cable (supplied).

• On the camera, set MENU (Setup) [USB Connection] to

[PC Remote] before you connect it.

• On the camera, set MENU (Setup) [PC Remote Settings]

[Still Img. Save Dest.] to [PC+Camera].

• Insert a memory card into the camera.

• If you will be using the camera for a long period of time, it is

recommended that you set MENU (Setup) 

[Auto Pwr OFF Temp.] to [High] on the camera.

1 Connect the multi terminal on the product with the Multi/

Micro USB Terminal on the camera using the multi terminal

connecting cable (supplied).

• You cannot connect the camera to the micro USB connector on the

product.

DSC-RX0

Camera control box

Hint

• Two cables with different lengths are supplied. Use the appropriate one for

the installation environment.

CCB-WD1

4-735-433-11(1)

C:\4735433111\4735433111CCBWD1CEE\01GB-CCBWD1CEE\01GB.indd

DTP data saved: 2017/11/29 16:03

PDF file created: 2017/11/29 16:09

Setting the MASTER/CLIENT (Master/Client) switch

Set the MASTER/CLIENT switch to

“MASTER” if you will be using one

camera.

To use multiple cameras at once,

set the switch on one of the camera

control boxes to “MASTER.” Then,

set the switches on the others to

“CLIENT.”

MASTER/CLIENT switch

When you change the setting

Set the ON/OFF (Power) switch to “OFF” to turn off the product before

changing the setting of the MASTER/CLIENT switch.

CCB-WD1

4-735-433-11(1)

C:\4735433111\4735433111CCBWD1CEE\01GB-CCBWD1CEE\01GB.indd

DTP data saved: 2017/11/29 16:03

PDF file created: 2017/11/29 16:09

Connecting the product to a computer or switching hub

Connect the product to a computer or switching hub using a commercially

available LAN cable.

1 Connect the LAN terminal on the product with the LAN port on

the computer or switching hub using a LAN cable.

• You cannot connect the computer or switching hub to the micro USB

connector or multi terminal on the product.

To the LAN port on the

computer or switching hub

• If you connect this product to a switching hub, connect your

computer to the same network.

Note

• Use a device without a router function or a device whose router function is

disabled as the switching hub to which you connect this product.

Andere Handbücher für CCB-WD1

Inhaltsverzeichnis

Andere Sony IP-Kamera Handbücher

Sony

Sony HDC1500R Bedienungsanleitung

Sony

Sony 3-AXIS INDOOR DOME CAMERA Bedienungsanleitung

Sony

Sony super motion hdc4300 Bedienungsanleitung

Sony

Sony HDC1000R Bedienungsanleitung

Sony

Sony SNCEM602R Bedienungsanleitung

Sony

Sony High Contrast License Plate Capture Camera Bedienungsanleitung

Sony

Sony HDC-X310 Bedienungsanleitung

Sony

Sony IPELA PCSA-CXA55 Bedienungsanleitung

Sony

Sony SRG120DH Bedienungsanleitung

Sony

Sony FCB-EX2700P Bedienungsanleitung

Sony

Sony IMX035 Bedienungsanleitung

Sony

Sony HDC-X300 Bedienungsanleitung

Sony

Sony Ipela SNC-CH135 Bedienungsanleitung

Sony

Sony URZ0146 Bedienungsanleitung

Sony

Sony HSC300RF Bedienungsanleitung

Sony

Sony BRCSDP16 Bedienungsanleitung

Sony

Sony HDC2580 Bedienungsanleitung

Sony

Sony FDR-X3000 Merkblatt

Sony

Sony SNC-ZB550 Bedienungsanleitung

Sony

Sony HXC-100 Bedienungsanleitung

Sony

Sony Ipela Benutzerhandbuch

Sony

Sony Effio-V Bedienungsanleitung

Beliebte IP-Kamera Handbücher anderer Marken

FLIR

FLIR Exx series Bedienungsanleitung

Avigilon

Avigilon H4A-BO1-IR Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWCA-C128-64 Bedienungsanleitung

ShareTech

ShareTech AV1 Bedienungsanleitung

Ezviz

Ezviz C6C Bedienungsanleitung

Melchioni

Melchioni UCAM 2015 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-4630 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Bedienungsanleitung

Mitel

Mitel 6800i Series Service-Handbuch

Vitek

Vitek VTC-IR403-212NP Bedienungsanleitung

THOMSON

THOMSON DSC - 323W Bedienungsanleitung

AVer

AVer FB2027 Bedienungsanleitung

ENFORCER

ENFORCER EV-T5105-N2SQ Bedienungsanleitung

Wansview

Wansview NC543 Bedienungsanleitung

Eneo

Eneo MCB-64A0003M0A Bedienungsanleitung

deView electronics

deView electronics CBDNI36F Bedienungsanleitung

Swann

Swann SwannEye Bedienungsanleitung

LevelOne

LevelOne IP CamSecure Bedienungsanleitung