Sony HKSP-1125 Bedienungsanleitung

HD UP CONVERTER BOARD

HKSP-1125

INSTALLATION MANUAL

1st Edition (Revised 1)

Serial No. 10001 and Higher

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt dieAngaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

1 (E)

HKSP-1125

Purpose of this manual

This manual is an installation manual of HD Up Converter

Board HKSP-1125.

This manual is intended for use by trained system and

service engineers, and describes information regarding

installation.

Related manuals

Besides this installation manual, the following manuals are

available for the HKSP-1125.

.Maintenance Manual (Available on request)

This manual describes the information that premises the

parts level service (adjustment, parts list, diagrams, etc.).

If this manual is required, please contact your local Sony

Sales Office/Service Center.

.“Semiconductor Pin Assignments” CD-ROM (Available

on request)

This “Semiconductor Pin Assignments” CD-ROM

allows you to search for semiconductors used in B&P

Company equipment.

Part number: 9-968-546-XX

1. Installation

The HKSP-1125 is composed of the following items.

.Main board (DPR-215A board)

.Connector board (DIF-137A board)

.Unit label (2pcs)

.Operation guide

.Installation manual

Attaching HKSP-1125

The HKSP-1125 is designed to be installed and operated in

the signal processing unit PFV-SP series.

In accordance with the installation manual of the PFV-SP

series, be sure to attach the main board and connector

board of the HKSP-1125.

This unit uses two slots of PFV-SP series. Remove the

two-slot blank panels when installing the connector board.

Matching connector/cable

When external cables are connected to the connectors on

the connector board, the hardware listed below (or equiva-

lents) must be used.

SDI IN, VIDEO IN, HD OUT

Connector: BNC (75 Z)/1-569-370-12

Cable: Fujikura 5C-2V cable

REMOTE

Connector: 9P, Male/1-566-354-XX

Cable: 9P-9P remote control cable

RCC-5G (5 m)

RCC-10G (10 m)

Shell: Hood for 9 pin/9-885-028-89

DDK Ltd. 17JE-09H-1A or equivalent

Be sure to use the remote control cable RCC-5G/10G

without attaching the spring lock plate.

Spring lock plate

OK NG

2 (E) HKSP-1125

2. Name and Function of Connector

1SDI IN (SDTV serial digital video signal input)

connector (BNC-type)

This connector inputs a SDTV serial digital video

signals of D1 SDI (525/625) and D2 SDI (525).

2VIDEO IN (NTSC analog video signal input)

connector (BNC-type)

This connector inputs an analog NTSC video signal.

3HD OUT (HDTV serial digital video signal

output) connectors (BNC-type)

The video signal input to the SDI IN and VIDEO IN

connectors is processed according to the operating

mode and then output.

The same signal is output from connectors 1 and 3.

49PIN/GPI connector (D-sub 9 Pin)

This connector is the input/output connector of an

external controls which connecting the HD digital

video controller HKDV-900.

Moreover, this connector can also be used as GPI. The

selection is performed by the menu of this unit.

3. Name and Function of Switch and

Indicator

The switches and indicators on the operation panel and

main board (DPR-215A board) are described below.

3-1. Operation Panel

REMOTE

(RS-422)

SDI IN

VIDEO IN

1125

HD OUT

HD UP-CONVERTER

HKSP-1125

PUSH

EXIT

ANALOG

AUDIO IN

REF IN

VIDEO IN

STATUS

D2 SDI

D1 SDI

3 (E)

HKSP-1125

Dial and switch (Refer to Section 5-1-1 for operation.)

No. Ref. No. Name Function

1EN1 Dial Selects the setting item and data.

(LED-395A board) Select: Turn the dial.

Determine: Press the dial.

2S1 EXIT key Returns to the display mode when this switch is pressed in the input

(LED-395A board) mode.

Displays

No. Ref. No. Name Function

3ND1 Upper Display Displays the setup and operation data items.

(LED-394A board)

4ND2 Lower Display Displays the values of setup and operation data.

(LED-394A board)

Indicators

No. Ref. No. Name Function

5D1 STATUS Lights in green: Under normal operation

(LED-393A board) Blinks in green: A warning occurs. (Refer to Section 6-1-2.)

Blinks in red: An error occurs. (Refer to Section 6-1-1.)

Off: The power supply of the main board is abnormal or

CPU is not activated.

When an error and warning are occurred simultaneously, error

overrides the warning.

For details, refer to Sections 5-2 and 6.

6D2 VIDEO IN Lights in green: A SD video input signal is normal.

(LED-393A board) Lights in red: A SD video input signal is abnormal or dose not match

with the setting of a format.

Off: A SD video input signal does not exist.

7D3 REF IN Lights in green: A selected reference signal is normal.

(LED-393A board) Lights in red: A selected reference signal is abnormal.

Off: A selected reference signal does not exist.

8D4 AUDIO IN Lights in green: An audio input signal is normal.

(LED-393A board) Lights in red: An audio input signal is abnormal.

Off: An audio input signal does not exist.

9D6 D1 SDI Lights in green: A D1 SDI input mode is selected.

(LED-393A board) Off: Other mode is selected.

!/ D7 D2 SDI Lights in green: A D2 SDI input mode is selected.

(LED-393A board) Off: Other mode is selected.

!- D8 ANALOG Lights in green: An ANALOG input mode is selected.

(LED-393A board) Off: Other mode is selected.

4 (E) HKSP-1125

3-2. Main Board (DPR-215A Board)

Switches (Factory default settings are indicated by a \\

\mark.)

No. Ref. No. Name Function

1S1901 RESET The DPR-215A board performs the same operation as during the power-on

sequence when this switch is pressed.

Do not use during normal operation.

2S600 STATUS Status out select switch

1-8 (\ON)

For details about this switch, refer to Section 5-2.

3S601 TEST Test switch

1-8 (\OFF)

Factory use only.

4S1900 NORM/DOWN CPU program rewrite switch

(\NORM)

Do not use during normal operation.

S1901

S1900

S601

S600

14 3 2

5 (E)

HKSP-1125

4. Operating Function

The HD up converter board HKSP-1125 converts the standard TV signal (SDI) to high definition TV

signal (HD SDI), and has an additional function required for conversion.

Input/Output

.Input signal can be selected from the following four video signals.

D1 SDI (59.94i)

D1 SDI (50i)

D2 SDI (59.94i)

NTSC ANALOG (59.94i)

.Output signal can be selected from the following four signal systems according to the selected signal

mentioned above.

1080i/59.94: D1 SDI (59.94i) /D2 SDI (59.94i) /NTSC ANALOG (59.94i)

1035i/59.94: D1 SDI (59.94i)/ D2 SDI (59.94i) /NTSC ANALOG (59.94i)

1080i/50: D1 SDI (50i)

720p/59.94: D1 SDI (59.94i) /D2 SDI (59.94i) /NTSC ANALOG (59.94i)

Genlock System

The sync signal of the output signal can be selected from internal sync INPT, external sync REFA and

REFB. If the external sync signal is selected, the frame synchronizer function operates automatically.

.Internal Synchronization Mode

.The system delay is fixed to 1Frame.

.When the unit is operating in this mode, the audio rate convert function can not operate irrespective of

the setting (ON/OFF) of the audio rate convert function ADRC.

The delay amount of audio is fixed to 1Frame. But, it is possible to adjust it by the system delay SYC,

SY-F and audio delay ADLY. (For more details, refer to Section “5. Setting”.)

0_1f 0_2f 1_1f 1_2f

1Frame

Video input signal

Video output signal

6 (E) HKSP-1125

.External Synchronization Mode (Frame Synchronizer Mode)

When the external sync signal is delayed α(660H or less).

When the external sync signal is advanced β(1Frame _660H or less).

When the unit is operating in this mode, the audio rate convert function is switched to ON/OFF according

to the setting (ON/OFF) of the audio rate convert function ADRC. The audio delay is fixed to 1Frame.

But, it is possible to adjust it by the system delay SYC, SY-F and audio delay ADLY. (For more details,

refer to Section “5. Setting”.)

Motion Sensitivity Adjustment Function

According to the motion, the ratio converts from a field or a frame is changed adaptively and processed.

The sensitivity can be adjusted in five steps.

Aspect Ratio

The aspect ratio of the output video signal can be selected from Edge crop, Letter Box, or Squeeze. The

position can be adjusted in each aspect ratio.

Color Corrector Function

The color corrector function can be selected from YPbPr, HUE, or RGB, and the white clip and black clip

adjustments can also be performed.

0_1f 0_2f 1_2f

0_1f 0_2f 1_1f 1_2f

1Frame + α

External sync signal

Video input signal

Video output signal

1_1f

0_1f 1_2f

0_2f 1_1f 1_2f

1Frame −β

External sync signal

Video input signal

Video output signal

1_1f0_2f

0_1f

7 (E)

HKSP-1125

Back-color Control Function

The back-color control function has the following features.

.Color adjustment of color matte

.Position adjustment for back-color area

.Enables the layout and super-impose of the intake picture into back.

Ancillary Data Multiplexing

Multiplexes the auxiliary data such as VITC, digital super imposed data, and so on to HD SDI signal.

Audio

Audio signal can be delayed up to 2 Frames, and corresponds to 8 channels.

8 (E) HKSP-1125

5. Setting

Each item can be set using the operation panel.

The operation of the operation panel and the setting of

setup switches on the main board are described below.

The several setting items and operation modes are always

stored, so it is not necessary to reset the settings by the

POWER ON/OFF etc.

5-1. Setting Using Operation Panel

5-1-1. Operation

Upper Display: Displays the item (menu).

Lower Display: Displays the set value.

Turn the dial clockwise: The item advances.

Turn the dial counterclockwise:

The item returns.

Press the dial: The hierarchy of a menu turns

into lower by one.

The set value is determined.

EXIT key: The hierarchy of a menu returns

by one.

For the configuration and hierarchy of a menu, refer to

Sections “5-1-2. Menu Configuration”and “5-1-3. Menu

List”.

Basic operation

1. Turn the dial and select the menu to be set.

2. Press the dial to turns into the lower hierarchy of a

menu by one.

3. When it is determined at the bottom of the hierarchy,

the display returns to the system menu.

The system automatically returns to the HOME menu

mode when, in the input mode, the state of no operation

continues over a fixed period of time (about 5 minutes).

HD UP-CONVERTER

HKSP-1125

PUSH

ANALOG

EXIT

AUDIO IN

REF IN

VIDEO IN

STATUS

D2 SDI

D1 SDI

Upper display

Lower display

Dial

EXIT key

Andere Handbücher für HKSP-1125

Inhaltsverzeichnis

Andere Sony Medienkonverter Handbücher

Sony

Sony DVMC-DA1 Bedienungsanleitung

Sony

Sony TDM-NC1 - Wi-fi Client For Streaming Music Montageanleitung

Sony

Sony NU-NM11B Kurzanleitung zur Einrichtung

Sony

Sony SQD-2020 Einrichtungshandbuch

Sony

Sony VAIO PCWA-DE30 Bedienungsanleitung

Sony

Sony BKSM-T103 Bedienungsanleitung

Sony

Sony NSBK-A16H Bedienungsanleitung

Sony

Sony VGF-WA1/B - Vaio Wireless Digital Music... Bedienungsanleitung

Sony

Sony CarrierGate PCWA-DE50 Bedienungsanleitung

Sony

Sony PCWA-DE80 - Wireless Lan Router Bedienungsanleitung

Sony

Sony BKPF-012A Bedienungsanleitung

Sony

Sony DSC-1024HD Bedienungsanleitung

Sony

Sony BKPF-L752 Bedienungsanleitung

Sony

Sony DSC-1024HD Bedienungsanleitung

Sony

Sony DVA-P1100 Bedienungsanleitung

Sony

Sony HDRC-4000 Bedienungsanleitung

Sony

Sony PCWA-DE80 Bedienungsanleitung

Sony

Sony HKPF-9000 Bedienungsanleitung

Sony

Sony XDBK-103 Bedienungsanleitung

Sony

Sony HKSP-313 Bedienungsanleitung

Sony

Sony VGF-WA1/W - Vaio Wireless Digital Music... Bedienungsanleitung

Sony

Sony NU-IP40D Bedienungsanleitung

Sony

Sony BKPF-101A Bedienungsanleitung

Sony

Sony TDM-NC1 - Wi-fi Client For Streaming Music Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung