Sony WRT-807A Bedienungsanleitung
3-866-337-12 (1)
WRT-807A
UHF Synthesized
Wireless Microphone
Operating Instructions
Manual de instrucciones
Mode d’emploi
Wireless Channel Lists
Listas de canales inalámbricos
Listes des canaux sans fil
1999 by Sony Corporation [U64] [U66] [U68]
US
ES
FR
Owner’s Record
The model and serial numbers are located at the rear of the
unit. Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony
dealer regarding this product.
Model No. WRT-807A Serial No.
Notice for customers in the U.S.A.
Use of Sony wireless devices is regulated by the Federal
Communications Commission as described in Part 74
subpart H of the FCC regulations and users authorized
thereby are required to obtain an appropriate license.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.
Notice for customers in Canada:
Use of Sony wireless devices is regulated by the Industry
Canada as described in their Radio Standard Specification
RSS-123.
A licence is normally required. The local district office of
Industry Canada should therefore be contacted. When the
operation of the device is within the broadcast band, the
licence is issued on no-interference, no-protection basis with
respect to broadcast signals.
Operation of this device is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Avis pour les clients au Canada:
L’usage des appareils sans-fil Sony est réglé par l’Industrie
Canada comme décrit dans leur Cahier des Normes
Radioélectriques CNR-123.
Une licence est normalement requise. Le bureau de
l’Industrie Canada doit être contacté. Lorsque l’opération de
l’appareil est dans les limites de la bande de radiodiffusion,
la licence est émanée sur la base de non-interférence, non-
protection avec les signaux de radiodiffusion.
L’utilisation de cet appareil est soumise aux deux conditions
suivantes : (1) cet appareil ne peut causer d’interférences, et
(2) cet appareil doit accepter toutes les interférences, y
compris les interférences capables de provoquer un
fonctionnement indésirable de l’appareil.
1
US
Table of Contents
English
English
US
Precautions................................................................1
Introduction ...............................................................2
Features .............................................................2
Parts Identification....................................................4
Power Supply ............................................................7
Settings ......................................................................8
Initiating Setting Mode .....................................8
Changing the Transmitting Channel .................8
Changing the Input Attenuation Setting..........10
Resetting the Accumulated Battery Use
Time Indication .........................................11
Troubleshooting...................................................... 12
Specifications..........................................................14
Error Messages .......................................................15
Precautions
• The unit is designed for use in ambient temperature range
of 0°C to 50°C (32°F to 122°F).
• Do not place the unit on or near heat sources, such as
lighting equipment, power amplifiers, or in a place subject
to direct sunlight or excessive moisture. In such places,
the external finish or internal parts of the unit may be
damaged.
• If the unit is used in a very humid or dusty place or in a
place subject to an active gas, clean its surface as well as
the connectors with a dry, soft cloth soon after use.
Lengthy use of the unit in such places or not cleaning it
after its use in such places may shorten its life.
• When cleaning the unit, never use organic solvents such as
thinners or benzine, which will damage the finish of the
unit.
• The unit has been factory adjusted precisely. Do not
tamper with its internal parts or attempt to repair it.
• Do not attempt to recharge an alkaline battery.
• Do not dispose of a battery in fire. Do not disassemble or
short-cirtuit a battery.
• Make sure to use an LR6 (size-AA) alkaline battery.
• Make sure the poles of the battery match the + and –
markings in the battery holder.
• Remove the battery when the unit will not be used for a
long period of time.
2
US
Introduction
The WRT-807A is a UHF-synthesized wireless microphone
for use in a 800-MHz band UHF-synthesized wireless
microphone system.
The WRT-807A operates in conjunction with the WRR-
800A/801A/802A/805A, MB-806A UHF Synthesized Tuner
for vocal concentration.
The WRT-807A can be also used with existing Sony
wireless microphone systems consisting of the WRT-810A/
820A/822A/830A UHF Synthesized Transmitter and WRR-
810A/820A/840A/850A UHF Synthesized Tuner.
The microphone/transmitter and tuners of the wireless
microphone system are classified by frequency band.
A 12 MHz frequency band (or two consecutive-numbered
TV channels, such as 68 and 69 of the U68 model) is
assigned to each microphone/transmitter and tuner model.
In building up a UHF wireless microphone system, be sure
to combine a microphone/transmitter and a tuner having the
same TV channel number.
For the selectable wireless channels and frequencies, see
“Wireless Channel Lists” on page L-1.
Features
Phase Locked Loop (PLL) synthesized system
The WRT-807A features a refined phase locked loop (PLL)
synthesizer circuit.
POWER switch with holding function
The POWER switch can be locked in the ON position to
protect against accidental power cut-offs.
Low-battery notification on tuner
When the microphone battery is low, the microphone sends
a warning to the WRR-800A/801A/802A/805A/850A, MB-
806A in the form of “Battery status information.”
This information is sent to the WRR-800A/801A/802A/
805A/850A, MB-806A about one hour before the battery
goes dead to allow the battery to be safely replaced.
When the WRR-800A/801A/802A/805A/850A, MB-806A
receives this information, the LED and the LCD on tuner
panel start to flash.
Powered by readily available battery type
The built-in, high-efficiency DC-DC converter provides
about five hours of continuous and stable operation with just
a single LR6 (size-AA) alkaline battery.
3
US
LCD readout of various information
The microphones LCD shows the current channel number,
frequency, input attenuation setting, and residual battery
power.
The accumulated battery use time is also indicated (in one-
minute increments) to allow precise monitoring of battery
use.
Automatic saving of channel and input attenuation
settings
All channel and input attenuation settings are automatically
saved when the microphone is turned off (and are
maintained even when the battery is removed), thus
eliminating the need to make the same settings again the
next time you use the microphone.
Highly reliable electronic attenuator
Adjustable in a range of 0 dB to 21 dB in 3-dB steps, the
built-in input level attenuator reduces signal distortion
during the input of excessively strong audio signals.
Tone signal-incorporated RF carrier signal
The microphone transmits an RF carrier signal that
incorporates a tone signal to enable any tuner with a tone
squelch circuit to pick out only the target audio signal.
Wide dynamic range and low noise
The microphones compander (compressor/expander) system
enables transmission over a wide dynamic range with
minimum noise.
Notes on operation
• When operating two or more microphones, keep the
microphones separated from each other by a distance of at
least 30 cm (1 foot).
• Keep microphones at least 3 meters (10 feet) away from
the receiving antenna.
4
US
6
5
4
7
2
3
1
8
Parts Identification
1Wind screen
Protects against noise caused by wind.
2Liquid-crystal display
AAF (audio input) indication
Lights whenever an audio signal stronger than the reference
level is received.
BRF (antenna output) indication
Lights during signal transmission from the antenna.
CBATT (battery) indication
Shows the battery condition.
See “Battery indication” on page 7.
Display example
for U68 model
AB
D
C
AF RF BATT
5
US
+
SET
–
DCH (channel) indication
Displays the transmitting channel.
Each time you press the SET button in Transmit mode, the
channel indication changes as follows.
Transmitting channel: The current transmitting channel
setting.
Transmitting frequency: The current transmitting
frequency setting.
Attenuation: The input attenuation setting in decibels.
Can be set within a range of 0 dB to 21 dB in 3-dB
steps.
Accumulated battery use time: The accumulated time of
battery use (in 1-minute increments).
Transmitting
channel
To adjust these parameters, see “Changing the Transmitting
Channel” on page 5, “Changing the Input Attenuation
Setting” on page 10 or “Resetting the Accumulated Battery
Use Time Indication” on page 11.
3SET button
In Transmit mode, press this button to change the indicated
items in the lower half of the liquid-crystal display.
To change to Setting mode, turn the POWER switch to ON
while holding this button down. Then press this button to
select the items to be indicated.
How to press the SET and +/– buttons
For details on Setting mode, see “Settings” on page 8.
Press the button with a
ballpoint pen or similar item.
Transmitting
frequency
Attenuation level
Accumulated
battery use time
Press SET button. Display example
for U68 model
6
US
ON
HOLD
.
ON
HOLD
.
4POWER indicator
Lights when the microphone is on.
5POWER switch
Turns the microphone ON or OFF.
When you set this switch to ON without holding down any
other button, the microphone enters Transmit mode, and the
signal of the selected channel is transmitted.
The HOLD switch appears when the POWER switch is set
to ON.
Set the HOLD switch to the lock position to prevent an
accidental power cut-off during microphone operation.
Locking the POWER switch
Slide the HOLD switch to the
right with a ballpoint pen or
similar item.
6Antenna
7Battery holder
Insert the battery here.
For details on inserting the battery, see “Power Supply” on
page 7.
8+ (+ selection) / – (– selection/reset) buttons
In Setting mode, use these buttons to select the transmitting
channel and attenuation level, and use the – button to reset
the accumulated battery use time indication to 00:00.
For details on Setting mode, see “Settings” on page 8.
A yellow mark appears
when the switch is in the
hold position.
/
Parts Identification
7
US
1234
BATT
indication
Lights Lights Flashes Goes off
Battery
condition Good Less than
half-charge Almost
exhausted Completely
exhausted
2
1,3
E
e
Power Supply
The microphone can operate on one LR6 (size AA) alkaline
battery continuously for about 5 hours at 25 ºC (77ºF).
Inserting the battery
1Turn the grip in the direction of the arrow to open the
battery holder.
2Match the battery to the polarity markings and insert it
into the battery holder.
3Close the battery holder and lock the grip by turning it
in the opposite direction of the arrow.
Battery indication
When you turn the power on, the battery condition is
indicated by the BATT indication in the liquid-crystal
display.
Note
The indication may be incorrect if the battery was not new
when inserted. If you plan to use the microphone for a long
period, replace the battery with a new one.
8
US
Channel selection
mode
Freqency selection
mode
Attenuator adjustment
mode
Accumulated time
indication reset mode
Press the
SET button.
Settings
Initiating Setting Mode
Enter Setting mode to change the transmitting channel, the
transmitting frequency and the attenuation level, or to reset
the accumulated battery use time indication.
To enter Setting mode
While holding down the SET button, turn the POWER
switch to ON.
Hold the SET button down until an indication appears on the
liquid-crystal display.
The microphone enters Setting mode and the indication
before the microphone was previously turned OFF flashes
on the liquid-crystal display.
Pressing the SET button cycles the modes in the order of
Channel selection mode, Frequency selection mode (page
8), Attenuator adjustment mode (page 10) and Accumulated
time indication reset mode (see page 11).
Changing the Transmitting Channel
The transmitting channel can be selected through either the
channel number or the frequency.
1Set the microphone to Setting mode.
If the channel number (or frequency) indication does not
appear, press the SET button until the channel number
(or frequency) indication appears.
Display example
for U68 model
Andere Handbücher für WRT-807A
1
Inhaltsverzeichnis
Sprachen:
Andere Sony Mikrofon Handbücher
Sony
Sony ECM-W2BT Referenzhandbuch
Sony
Sony handycam ecm-hst1 Bedienungsanleitung
Sony
Sony SXA-J750 Bedienungsanleitung
Sony
Sony ECM-CR120 Bedienungsanleitung
Sony
Sony ECM-ALST1 Bedienungsanleitung
Sony
Sony UTX-B03 Bedienungsanleitung
Sony
Sony Electret ECM-Z37C Bedienungsanleitung
Sony
Sony ECM-44B Bedienungsanleitung
Sony
Sony ECMCG50BP Bedienungsanleitung
Sony
Sony ECM-HQP1 Bedienungsanleitung
Sony
Sony ECM CG1 Bedienungsanleitung
Sony
Sony ECM-957PRO Bedienungsanleitung
Sony
Sony ECM-DS70P Bedienungsanleitung
Sony
Sony Electret Bedienungsanleitung
Sony
Sony C-55P Technisches Dokument
Sony
Sony ECM-55B Bedienungsanleitung
Sony
Sony ECM-999 Bedienungsanleitung
Sony
Sony F-V220 - Uni-Directional Vocal Microphone Bedienungsanleitung
Sony
Sony ECM-673 Bedienungsanleitung
Sony
Sony MAS-A100 Kurzanleitung zur Einrichtung
Beliebte Mikrofon Handbücher anderer Marken
IK Multimedia
IK Multimedia iRig Stream MIC PRO Bedienungsanleitung
DAPAudio
DAPAudio RM-101 Bedienungsanleitung
AKG
AKG CHM 21 Bedienungsanleitung
Sennheiser
Sennheiser evolution wireless series EM 100 Bedienungsanleitung
GIGAMEDIA
GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung
Shure
Shure WH30TQG Bedienungsanleitung
