Sony XVM-61EX/6100 Bedienungsanleitung

– 1 –

Supplied accessories

Controller (RM-X6100) (1) (XVM-6100 only)

Monitor cable (1)

Hideaway unit (XA-602) (1) (XVM-61EX only)

Video selector (XA-601) (1) (XVM-6100 only)

Design and specifications are subject to change

without notice.

SERVICE MANUAL

US Model

XVM-6100

UK Model

E Model

German Model

XVM-61EX

XVM-61EX/6100

EXTENSION MONITOR SYSTEM

Monitor (XVM-611/611EX)

System Liquid crystal color display

Display Transparent TN LCD panel

Drive system TFT active matrix system

Picture size 6 in. ; 121.9 ×89.2 mm (4 7/8

×3 5/8in.), 151 mm (6 in.)

(w ×h, diagonally)

Picture segment 224,640 (w 960 ×h 234)

Speaker type ø 5 cm (ø 2 in.) dynamic

speaker

Power requirements12 V DC car battery

(negative ground)

Current drain Approx. 0.7 A

Dimensions 162 ×129 ×31 mm (6 1/2×

5 1/8×1 1/4in.) (w ×h ×d)

Operating temperature

+5 ˚C ~ +45 ˚C

(41 ˚F ~ 113 ˚F)

Mass Approx. 430 g (15.3 oz.)

Controller (RM-X6100) (XVM-6100 only)

Dimensions 178 ×50 ×40 mm (6 1/2×

2 ×1 1/4in.) (w ×h ×d)

Operable range Approx. 3 m (118 1/4in.)

Mass Approx. 400 g (14.1 oz.)

(including cable)

SPECIFICATIONS

MICROFILM

Notes on Chip Component Replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

Photo : XVM-611EX (Monitor)

XVM-61EX XVM-6100

MONITOR XVM-611EX XVM-611

VIDEO SELECTOR XA-601

CONTROLLER RM-X6100

HIDEAWAY UNIT XA-602

•This set consists of the following units.

XVM-6100

XVM-61EX

MOBILE COLOR MONITOR SYSTEM

– 2 –

TABLE OF CONTENTS

1. GENERAL .......................................................................... 3

2. ELECTRICAL ADJUSTMENTS

Monitor Section ...................................................................... 4

Video Selector Section (XVM-6100 only) ............................. 6

3. DIAGRAMS

3-1. Block Diagram

– Monitor Section (XVM-611/611EX) –........................... 7

3-2. Block Diagram – Video Selector Section (XA-601) – ....... 9

3-3. Block Diagram – Hideaway Unit Section (XA-602) – .... 10

3-4. Block Diagram – Controller Section (RM-X6100) –....... 11

3-5. Printed Wiring Board

– Monitor Section (XVM-611/611EX) –......................... 13

3-6. Schematic Diagram

– Monitor Section (XVM-611/611EX) –......................... 17

3-7. Schematic Diagram

– Video Selector Section (XA-601) – .............................. 22

3-8. Printed Wiring Board

– Video Selector Section (XA-601) – .............................. 25

3-9. Schematic Diagram

– Hideaway Unit Section (XA-602) –.............................. 28

3-10. Printed Wiring Board

– Hideaway Unit Section (XA-602) –.............................. 31

3-11. Printed Wiring Board

– Controller Section (RM-X6100) – ................................ 33

3-12. Schematic Diagram

– Controller Section (RM-X6100) – ................................ 35

4. EXPLODED VIEWS

4-1. Monitor Section (XVM-611/611EX)............................... 39

4-2. Video Selector Section (XA-601) .................................... 40

4-3. Controller Section (RM-X6100) ...................................... 41

4-4. Hideaway Unit Section (XA-602).................................... 42

5. ELECTRICAL PARTS LIST ................................... 43

– 3 –

SECTION 1

GENERAL This section extracted from

XVM-6100’s instruction manual.

– 4 –

SECTION 2

ELECTRICAL ADJUSTMENTS

Equipment

Use the following test equipment for alignment.

• Oscilloscope dual trace, 10 MHz band or above with delay mode

(use a 10 to 1 probe unless otherwise instructed.)

• NTSC color bar generator

• PAL color bar generator

• DC power supply

• Digital voltmeter

• XT-61VE (TV tuner unit of XTL-610E) (XVM-61EX only)

• Frequency counter

Equipment Connections

Make the test equipment connections as shown below (unless

instructed otherwise) and perform the alignment.

XVM-61EX :

NAVI INPUT

(VIDEO)

color bar

generator XT-61VE XVM-611EX

VIDEO output

(75

Ω

)MONITOR OUTPUT

INPUT 1

(VIDEO) MONITOR OUTPUT

CONTROLLER

XA-601 XVM-611

color bar

generator

VIDEO output

(75

Ω

)

RM-X6100

XVM-6100 :

MONITOR SECTION

Voltage Adjustment

Setting :

DIMMER selector (S701) : HIGH

BRIGHT dial (RV702) : Max. (light)

VOL dial (RV301) : Max.

Procedure :

1. Input the color bar (chroma off) signal from NTSC color bar

generator and display on the monitor screen.

2. Connect the digital voltmeter to CL66 on the monitor main

board.

3. Adjust RV401 (+5V) so that the digital voltmeter reads 5±0.1 V

DC.

4. Connect the digital voltmeter to CL86 on the monitor main

board.

5. Adjust RV601 (+9V) so that the digital voltmeter reads 8.5±0.1 V

DC.

Connection points : Monitor main board Refer to page 5.

Alignment points : Monitor main board Refer to page 5.

RGB Adjustment

Procedure :

1. Input the color bar (chroma off) signal from NTSC color bar

generator and display on the monitor screen.

2. Connect the digital voltmeter to CL151 on the monitor main

board.

3. Adjust RV213 (OFFSET) so that the digital voltmeter reads

2.3±0.1 V DC.

4. Connect the oscilloscope to CL42 on the monitor main board.

5. Adjust RV212 (COM CUT) so that the lower black level is

6.2±0.05 V DC.

6. Adjust RV208 (COM DRIVE) so that the upper 100% white

level is 9.2±0.05 V DC.

7. Repeat steps 5 & 6 until the items in the standards are satisfied.

8. Connect the oscilloscope to CL41 of the monitor main board.

9. Adjust RV207 (R DRIVE) so that the lower black level is

6.2±0.05 V DC.

10. Adjust RV202 (R CUT) so that the upper 100% white level is

9.2±0.05 V DC.

11. Repeat steps 9 & 10 until the items in the standards are satisfied.

12. Connect the oscilloscope to CL43 of the monitor main board.

13. Adjust RV209 (B DRIVE) so that the upper 100% white level

is 6.1±0.05 V DC.

14. Adjust RV204 (B CUT) so that the upper 100% white level is

9.1±0.05 V DC.

15. Repeat steps 13 & 14 until the items in the standards are satisfied.

white level (1st step)

black level (8th step)

0 V

Connection points : Monitor main board Refer to page 5.

Alignment points : Monitor main board Refer to page 5.

– 5 – – 6 –

V COM Adjustment

Procedure :

1. Connect the oscilloscope to CL44 on the monitor main board.

2. Adjust RV210 (V COM AMP) & RV211 (V COM BIAS) so

that the output waveform is within the standards.

3. Repeat step 2 until the standards are satisfied.

Standard values :

A: Adjust RV210 so the value is 4.9±0.1 Vp-p.

B: Adjust RV211 so the value is 5.1±0.1 V.

0 V

Connection points : Monitor main board

RV207

R DRIVE

ADJ

RV208

COM DRIVE

ADJ

RV213

OFFSET

ADJ

RV212

COM CUT

ADJ

RV202

R CUT

ADJ

RV209

B DRIVE ADJ

RV204

B CUT ADJ

RV210

V COM AMP ADJ

RV211

V COM BIAS ADJ

RV401

+5V ADJ

RV601

+9V ADJ

– MONITOR MAIN BOARD (COMPONENT SIDE) –

– MONITOR MAIN BOARD (CONDUCTOR SIDE) –

CL44 CL43 CL41 CL66

CL42

CL151

Alignment points : Monitor main board

VIDEO SELECTOR SECTION (XVM-6100 only)

NTSC Adjustment

Procedure :

1. Input the color bar signal from NTSC color bar generator on

the AV selector board.

2. Connect the frequency counter to TP61 (SC OUT).

3. Confirm reading the frequency counter is 3.579545 MHz.

4. Connect the oscilloscope to CN3 !£ pin (B OUT).

5. Adjust RV1 (Y.C ADJ) so that white peak (100% white) is

1.00 Vp-p.

6. Adjust RV2 (HUE ADJ) and RV3 (COL ADJ) so that amplitude

of each color is same (A=B=C=D).

PAL Adjustment

Procedure :

1. Input the color bar signal from PAL color bar generator on the

AV selector board.

2. Connect the frequency counter to TP61 (SC OUT).

3. Confirm reading the frequency counter is 4.433619 MHz.

4. Connect the digital voltmeter to IC10 !¢ pin (DLA BIAS).

5. Adjust RV5 (DLA BIAADJ) so that reading the digital voltmeter

is 2.3 V.

6. Adjust RV1 (Y.C ADJ) so that white peak (100% white) is

1.00 Vp-p.

7. Adjust RV2 (HUEADJ) and RV3 (COLADJ) so that amplitude

of each color is same (A=B=C=D).

Alignment points : AV selector board

ABCD

1 Vp-p

SYNC

OUT

B OUT

ABCD

1 Vp-p

SYNC

OUT

B OUT

– AV SELECTOR BOARD (COMPONENT SIDE) –

– AV SELECTOR BOARD (CONDUCTOR SIDE) –

RV1

Y.C ADJ

RV3

COL ADJ

RV4

APC ADJ

RV2

HUE ADJ

RV5

DLA BIA ADJ

IC10

CN3

TP61

(SC OUT)

Connection points : AV selector board

– 7 – – 8 –

XVM-61EX/6100 SECTION 3

DIAGRAMS

3-1. BLOCK DIAGRAM — MONITOR SECTION (XVM-611/611EX) —

: AUDIO

: VIDEO

AUDIO

POWER AMP

IC301 CN3

SP301

SPEAKER

CLAMP

Q11

10 11

1 2

CLAMP

Q21

OFFSET

CANSEL

POLARITY

SELECT

RECTIFY

DISPLAY

SELECT

OUTPUT

AMP

LEVEL

ADJUSTMENT

PULSE

CONVERSION

CURRENT

CONVERSION CURRENT CONVERSION

16 17 18 19

RV213

OFFSET

RV212

COM

CUT

RV202

CUT

RV204

CUT

CURRENT CONVERSION F. F.

12 13 14 21

5 1

RV209

DRIVE

RV207

DRIVE

RV208

COM

DRIVE

COUNT

DOWN

VERTICAL

SEP

32FH

VCO

VIDEO CHROMA INTERFACE,

γ-AMP, DRIVE AMP

IC201

RV702

BRIGHT

RV301

VOL

B+ (+5V)

B+

(+5V)

Q Q

SINGLE SHOT

IC203

SYNC

SEP AFC

X202

480kHz

SYNC SEP

IC202

POWER

RV601

+9V

RV401

+5V

REG

IC302

D102

POWER

F901

F501

F601 B+

SWITCH

Q609

B+

ON/OFF

Q605, 606

B+ (+23V)

B+ (+13V)

B+ (+5V)

B- (-5V)

B+ (+9.1V)

B+ (+8.7V)

OUT2

+IN1

OUT1 SCP

+IN2

INVERTER

Q502-504

DC-DC

CONVERTER

IC401

DC-DC

CONVERTER

T501

PROTECTOR

Q401

D505

D504

D503

D502

D401

BL B+

SWITCH

Q602

V COM

AMP

Q211

V COM

BIAS

Q207-210

ON/OFF

Q801, 802

DRIVE

Q601

REG

Q604

SWITCH

Q610

INVERTER

Q607, 608

IC601 (3/3)

12 14

IC601 (1/3)

810

IC601 (2/3)

HIGH

LOW

S701

DIMMER

BUFFER

Q603

DIMMER

IC601

CN1

AUDIO IN

BEEP

R. IN

G. IN

B. IN

BRIGHT

C. SYNC

NTSC/PAL

POWER.

BL. ON/OFF

+B (+12V)

SELECTOR

BOARD

CN3

(XA-601)

RV210

V COM AMP

RV211

V COM BIAS

B+

VGG (+23V)

VBB (+13V)

VDD (+5V)

VEE (-5V)

CN8

10 V COM

21 POLC

22 POLS

24 HD

23 VD

N/S

B+

(+23V)

B+

(+13V)

B+

(+5V)

B-

(-5V)

CN601

GND

BACK-LIGHT

UNIT

DSP301

LIQUID CRYSTAL

DISPLAY

PANEL

Signal Path

DC-AC

CONVERTER INVERTER

T601

MONITOR MAIN BOARD

BUNPAIKI

BOARD

CN4

(XA-602)

(Page 11)

(Page 10)

– 9 – – 10 –

3-2. BLOCK DIAGRAM — VIDEO SELECTOR SECTION (XA-601) —

G SIGNAL

AMP

Q222

SYNC

SEP

BURST

GATE

+5V

ACC

F101

GND

POWER

+5V

VIDEO

AMP

Q81

SHARP

PAL ID

VXO

APC

INV

HUE

DEM

CN1 +5V REG

IC3

+5V REG

IC5

Y IN

SYNC

AUDIO

AMP

Q201, 202

BUFFER

Q102

SWITCH

Q105

R SIGNAL

AMP

Q223

B SIGNAL

AMP

Q221

Y/C

MIX

ADD/SUB

CHROMA

AMP

PULSE

GEN

Y SIGNAL

AMP

Q101

SWITCH

Q109

VIDEO

AMP

Q601

RELAY

DRIVE

Q104

POWER

CONTROL

Q1-5

VIDEO

AMP

Q22, 23

VIDEO

AMP

Q42, 43

AMP

RGB DECODER

IC10

SIG AMP

DL2

+12V

MUTE

DRIVE

Q94

VIDEO

AMP

Q71

VIDEO

AMP

Q91

DLA BIA.

ADJ

COL. ADJ

RV3

RV1

Y. C. ADJ

HUE. ADJ

RV2

APC. ADJ

RV4

J3-1 VIDEO 1

J4-1 VIDEO 2

(THROUGH OUT)

AUDIO 1

AUDIO 2

(OUTPUT)

J5-1

(THROUGH OUT L)

J3-2

J4-2

J5-2 AUDIO L (OUTPUT)

J3-3

J4-3

J5-3 AUDIO R (OUTPUT)

VIDEO

AUDIO 1

AUDIO 2

(THROUGH OUT R)

L. OUT

CN2 CONTROLLER

R. OUT

V3 ON

V1/V2

AUDIO 3 (R) IN

AUDIO 3 (L) IN

VIDEO 3 IN

+5V

POWER. SW

NTSC/PAL

BRIGHT

AUDIO OUT

NTSC/PAL

POWER. SW

C. SYNC

BRIGHT

+B (+12V)

R. OUT

G. OUT

B. OUT

MONITOR OUTPUT

CN3

AV SELECTOR BOARD

VIDEO 1 J1-1

J2-1

VIDEO 2

(INPUT)

J1-2AUDIO L

J1-3

AUDIO R

(INPUT 1)

J2-2

AUDIO L

J2-3

AUDIO R

(INPUT 2)

IN2

IN1

IN2

OUT 1

OUT 2

OUT 1

OUT 2

AUDIO AMP

IC1

AUDIO AMP

IC2

MUTE

Q92

MUTE

Q93

RV5

IN1

IN 2

IN 3

IN1

IN 2

IN 3

OUT

SW2

SW1

SW2

SW1

IN1

IN 2

IN 3

OUT

SW2

SW1

VIDEO SWITCH

IC7

L-CH SWITCH

R-CH SWITCH

AUDIO

IC8

IC9

AUDIO

RY1

X1 3.579545MHz

X2 4.433619MHz

CKVCC

XQ D

POWER SWITCH

IC6

+5V

+12V

VXO1

VXO2

APC ADJ HUE ADJ

B OUT

G OUT

R OUT

DLA

C OUT

DLA BIAS

C SYNC 15

C IN

DL1

C ADJ

CONTROL

BOARD

CNJ1

(RM-X6100)

MONITOR

MAIN

BOARD

CN1

(XVM-611)

DC IN 12V

: AUDIO

: VIDEO

Signal Path.

XVM-61EX/6100

(Page 11)

(Page 7)

– 11 – – 12 –

XVM-61EX/6100

3-3. BLOCK DIAGRAM — HIDEAWAY UNIT SECTION (XA-602) —

VIN2

VIN1

VOUT2

VOUT1

VIN2

VIN1

VOUT2

VOUT1

VIN2

VIN1

VOUT2

VOUT1

3 1

VIN2

VIN1

VOUT2

VOUT1

R. OUT

G. OUT

B. OUT

C. SYNC

+B (+12V)

SIRCS

POWER. SW

BEEP

NTSC/PAL

AUX. V

BL. ON/OFF

R. OUT

G. OUT

B. OUT

C. SYNC

POWER. SW

+B (+12V)

AUDIO OUT

BRIGHT

CNJ2 CN1

R. IN

G. IN

B. IN

C. SYNC

SIRCS

BEEP

NTSC/PAL

POWER. SW

16 13

BUFFER

Q1, 2

AUX. V

BL. ON/OFF

77 BUFFER

Q14, 15

914 BUFFER

Q16, 17

AUDIO IN

BRIGHT

+12V

310 BUFFER

BUFFER

Q5, 6

BUFFER

Q7, 8

NTSC/PAL

MONITOR

(XVM-610E)

MONITOR

MAIN

BOARD

CN1

(XVM-611EX)

TV TUNER

(XT-61VE)

+12V

CN3

MAIN

CN4

SUB

CN2

+5V REG

IC1

XQ CK

SWITCH

IC6

POWER

CONTROL

Q11-13

ACC DET

Q9, 10

CN5

ACC

GND

+12V

+5V

BUNPAIKI BOARD

R SIGNAL AMP

IC2

G SIGNAL AMP

IC3

B SIGNAL AMP

IC4

C. SYNC SIGNAL AMP

IC5

F201

(POWER)

DC IN 12V

: AUDIO

: VIDEO

Signal Path

3-4. BLOCK DIAGRAM — CONTROLLER SECTION (RM-X6100) —

15 10

AUDIO 3 (R) OUT

AUDIO 3 (L) OUT

VIDEO 3 OUT

L. IN

POWER. SW

BRIGHT

R. IN

NTSC/PAL

12 4

13 3

16 13

14 2

V1/V2 15 1

V3 ON

+5V +5V

POWER

RV2

BRIGHT

RV1

PHONES

(HEADPHONES)

AUDIO

VIDEO

-3

-2

-1

(VIDEO INPUT 3)

(NTSC/PAL)

PAL NTSC

MUTE

VIDEO INPUT

CN1

EVR

CONT

EVR

MUTE1

MUTE2

HEADPHONE

AMP

IC1

+5V

IN1

IN2

MUTE1

MUTE2

PO1

PO2

CNJ1 CN2

AV SELECTOR

BOARD

CN2

(XA-601)

CONTROL BOARD

: AUDIO

: VIDEO

Signal Path

(Page 7)

(Page 10)

Inhaltsverzeichnis

Andere Sony Mikrofon Handbücher

Sony

Sony F-720 Bedienungsanleitung

Sony

Sony ECM 719 Bedienungsanleitung

Sony

Sony ECMMS2 Bedienungsanleitung

Sony

Sony ECM MS908C Bedienungsanleitung

Sony

Sony F115B Bedienungsanleitung

Sony

Sony UWP-C1 Bedienungsanleitung

Sony

Sony ECM-221 Bedienungsanleitung

Sony

Sony ECM Z60 Bedienungsanleitung

Sony

Sony ECM-999 Bedienungsanleitung

Sony

Sony C-80 Bedienungsanleitung

Sony

Sony ECM-MS957 Bedienungsanleitung

Sony

Sony ECM-969 Bedienungsanleitung

Sony

Sony ECM DM5P Bedienungsanleitung

Sony

Sony F-V220 - Uni-Directional Vocal Microphone Bedienungsanleitung

Sony

Sony ECM-W1M Bedienungsanleitung

Sony

Sony ECM-Z70 Bedienungsanleitung

Sony

Sony WRT-810A Bedienungsanleitung

Sony

Sony ECM-CS3 Bedienungsanleitung

Sony

Sony ECM-S930C Operating Instructions / Manual de instrucciones / Mode d’emploi / Manual de... Bedienungsanleitung

Sony

Sony ECMMS907 - Stereo Type Mic Bedienungsanleitung

Sony

Sony WRT-800A Bedienungsanleitung

Sony

Sony F-V310 Bedienungsanleitung

Sony

Sony ECM-CR120 Bedienungsanleitung

Sony

Sony ECM-DS70P Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

Shure

Shure WH30TQG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

Shure

Shure KSM141 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

Shure

Shure MXA710 Series Bedienungsanleitung

JLab

JLab GO TALK Bedienungsanleitung