Sony SU-PF1 Bedienungsanleitung

SU-PF1 4-092-988-25 (1)

4-092-988-25 (1)

Floating Stand

Instructions

Gebrauchsanweisung

Istruzioni

Mode d’emploi

Instructies

Οδηγίες

Yönergeler

Instrucciones

Instruções

Vejledning

Instruksjoner

Bruksanvisning

Käyttöohje

SU-PF1

For Customers and Sony Dealers in Europe

Floating Stand SU-PF1

00GB+01COV-APE.p65 04.1.28, 10:08 AM1

2(GB)

Thank you for purchasing this product.

To Customers

This product should only be installed by qualified Sony service representatives, as it requires at least two

people, special care, safety, and technique. Sony is not liable for any accidents or damages caused by incorrect

installation or handling. Your Statutory Rights (if any) are not affected.

WARNING

If the safety precautions are not observed or the product is used incorrectly, it may result in serious injury or fire.

This instruction manual shows the correct handling of the product and important precautions necessary to prevent

accidents. Be sure to read this manual thoroughly and use the product correctly. Keep this manual available for

future reference.

For Sony dealers

Installation of a plasma TV requires two people, special care and technique. When installing a plasma TV, refer to

this manual carefully. Sony is not liable for any accidents or damages caused by incorrect installation or handling.

Your Statutory Rights (if any) are not affected. Please give this manual to the customer after installation.

On Safety

Products by Sony are designed with safety in mind. If the products are used incorrectly, however, it may result in a

serious injury through fire, electric shock, the product toppling over, or the product dropping. Be sure to observe

the precautions for safety to prevent such accidents.

CAUTION

This Floating Stand is intended for use only with the following products. Use with other apparatus is capable of

resulting in instability causing possible injury.

Specified products (As of March 2004) : Flat Panel Colour TV

(KE-42MR1/KDE-P42MRX1/KE-P42MRX1/KE-50MR1/KDE-P50MRX1/

KE-P50MRX1/KLV-L42MRX1/KDL-L42MRX1(UK))

We recommend installing the Floating Stand a short distance away from the wall.

3(GB)

WARNING

If the following precautions are not observed, serious injury or death through fire, electric shock, the

product toppling over, or the product dropping can result.

Be sure to subcontract the installation to Sony dealers.

If persons other than Sony dealers do the installation work, this may result in serious injury, as the Display Unit

and the stand are very heavy.

Do not lean on or hang from the stand.

The stand may topple over and cause injury.

Be sure to take measures to prevent the stand from toppling over.

If you fail to do so, the Floating Stand may topple over during an earthquake and cause injury or property damage.

Anchor the stand to a wall, etc. to prevent it from toppling over.

Be sure to install the stand on a solid and flat floor.

Do not install the Floating Stand so that it leans in one direction. If you do so, the Floating Stand may topple over

or the Display Unit may fall. This may cause injury.

If you install the stand on a soft surface such as a mat or a carpet, lay a board over the designated location

beforehand.

Do not use a cracked stand.

Do not use the Floating Stand if any cracks appear in it.

The glass may break and the Display Unit may fall, or the stand may topple over.

This may cause injury.

Cracked Stand

English

4(GB)

WARNING

If the following precautions are not observed, serious injury or death through fire, electric shock, the

product toppling over, or the product dropping can result.

Do not lean on or hang from the stand with the Display Unit installed on it.

The stand may topple over and cause serious injury or death.

Do not cover the ventilation hole of the Display Unit.

If you cover the ventilation hole (with a cloth, etc.), heat may build up inside and

cause fire.

Do not allow the mains lead or the Display Interface Cable to be pinched.

•Do not allow the mains lead or the Display Interface Cable to be pinched when

you install the Display Unit on the stand. If the mains lead or the Display

Interface Cable is damaged, this may result in a fire or an electric shock.

•Do not step on the mains lead or the Display Interface Cable when you carry the

Display Stand. The mains lead or the Display Interface Cable may be damaged,

and this may result in a fire or an electric shock.

CAUTION

If the following precautions are not observed, injury or property damage may occur.

Do not install any equipment other than the specified product.

This stand is designed for use with the specified product only. If you install equipment other than specified, it may

fall and cause injury or property damage.

Attaching the Display Unit.

Be sure to attach the Display Unit to the stand with the supplied fixing plates. If the Display Unit is not attached

securely, it may fall and cause injury.

Do not apply weight to the glass or subject it to any kind of impact.

Do not apply weight to the glass with your hand when installing the Display Unit. Do not hit the glass with hard

objects, such as a screwdriver, etc.

The glass may break and cause injury.

5(GB)

When carrying the Floating Stand

Trying to move the Floating Stand alone, or without following the proper procedures, may cause injury. To avoid

this, be sure to follow the advice given below.

•Be sure that two or more persons carry the Floating Stand only after removing the Display Unit.

•Be careful not to allow your toes to be pinched under the bottom plate or the corner of the glass.

Do not subject the glass to excessive shock.

This stand is made of tempered glass, but care should be taken. If the glass breaks,

glass fragments could cause injury, so observe the precautions below.

•Do not hit the glass or drop sharp-pointed objects on the glass. Avoid excessive

shock.

•Do not scratch or poke the glass with sharp-edged objects.

•Do not let hard objects such as a vacuum cleaner hit the edges of the glass.

Note on installation

Install the stand on a solid and flat floor. Do not allow the stand to be installed at an angle or incline. To avoid this,

observe the following precautions.

–If you install the stand on a soft surface such as a mat or a carpet, lay a board over the designated location

beforehand.

– Do not install the stand in a place subject to direct sunlight or near a heater.

–Do not install the stand in a hot or humid place, or outdoors.

Note on use

To keep the stand clean, occasionally wipe the stand with a dry soft cloth. Stubborn stains may be removed with a

cloth slightly dampened with diluted detergent. Then wipe the area with a dry soft cloth. Do not use any type of

chemicals, such as thinner or benzine, as they may damage the finish of the stand.

6(GB)

For Sony dealers

Be sure to thoroughly read the safety precautions described above and pay

special attention to safety during the installation, maintenance, checking, and

repair of this product.

Be sure that two or more persons do the installation work.

Be sure that two or more persons install the Display Unit on the Floating Stand. If one person does the installation

work alone, this may result in an accident or injury. Be sure to keep small children away during the installation.

Be sure to install the Display Unit securely, following the proper procedure.

If the Display Unit is not installed securely, it may fall and cause injury.

Check the parts

Name Quantity Name Quantity

Floating Stand Fixing plate

7(GB)

Install the Display Unit

WARNING

If you allow the mains lead to be pinched under or between pieces of equipment, this may result in a short

circuit or an electric shock.

If you stumble over the mains lead or the Display Interface Cable, the stand may topple over, and cause injury.

Draw the mains lead and the Display Interface Cable through the hole on the

stand.

Decide on the installation location and lay the stand down before installing the Display Unit.

Since the Display Unit is heavy, it is recommended that you decide on the installation location beforehand and

lay the stand down there before installing the Display Unit on the stand.

Note

Do not push or pull the stand while it is on the floor. The rubber footings on the base of the stand may come off.

1Connect the mains lead and the

Display Interface Cable to the

Display Unit.

zTip

See the instruction manual of the Sony

Flat Panel Colour Television or LCD Color

Television for more details on connecting the

mains lead and the Display Interface Cable.

Notes

•If the weight of the Display Unit is placed on

the speakers, deformation or a loose

connection of the speakers may result. To

avoid this, observe the following. (KLV-

L42MRX1, KDL-L42MRX1(UK) only)

– Do not hold the speakers when carrying

the Display Unit.

–When connecting cables to the Display

Unit, place packing material, etc. on the

floor and lay the Display Unit face down

on it so that the speakers on either side of

the Display Unit are clear of the packing

material, etc.

•Be sure to place the Display Unit stably.

•Use soft cloth to protect the screen of the

Display Unit from damage or dirt.

Rear side of the Display Unit

Soft rag

Mains lead

Display

Interface Cable

KE-42MR1/KDE-P42MRX1/KE-P42MRX1/

KE-50MR1/KDE-P50MRX1/KE-P50MRX1

KLV-L42MRX1/KDL-L42MRX1(UK)

Soft rag Speaker (right)

Speaker (left) Packing material, etc.

Rear side of the

Display Unit

Mains lead

Display Interface

Cable

Illustrations without model names that appear from now on are based on the Flat Panel colour television KLV-

L42MRX1, KDL-L42MRX1(UK).

8(GB)

2Install the Display Unit on the stand.

1Draw the mains lead and the Display Interface Cable through the hole on the stand.

2Check the position of the four holes on the fixtures on the stand beforehand.

Fit the hooks on the rear of the Display Unit into the holes on the fixtures of the stand.

3Confirm that the hooks on the rear of the Display Unit are completely inserted into the four holes on the

fixtures. Then slide the Display Unit straight downward until it snaps on.

Rear side of

the Display Unit

Hook

Front side of the stand

9(GB)

Mains lead and Display Interface

Cable

Fix the Display Unit

Attach the fixing plate to prevent the Display Unit from falling.

1Insert the fixing plate between the screw on the upper part of the fixture on the stand and the hook on the

Display Unit.

2Slide the fixing plate until the corner of the L-figure hits against the screw.

Fixing plate

3Take up the slack out of the mains lead and Display Interface Cable

already drawn through the hole on the stand.

Pull the ends of the mains lead and Display Interface Cable already drawn through the hole on the stand and

take up the slack out of the lead and the cable.

10(GB)

Anchor attachment

Safety measures to prevent toppling over

WARNING

Be sure to take measures to prevent the stand from toppling over. If you fail to do so, the Floating Stand may

topple over during an earthquake and cause injury or property damage. Anchor the stand by using a rope or

chain with fastening one end of it to the securing hook and the other end to the wall or pillar.

Prepare a commercially available rope or chain and wall anchor bracket beforehand.

1Secure the wall anchor bracket to a solid wall or pillar.

2Pass the rope or chain through both holes of the anchor attachments and then tighten the other end of the

rope or chain to the wall anchor bracket.

Wall anchor

bracket

Inhaltsverzeichnis

Sprachen:

Andere Sony Rack & Stand Handbücher

Sony

Sony SU-B553S Bedienungsanleitung

Sony

Sony VCT-HM1 Bedienungsanleitung

Sony

Sony SU-PF1L Bedienungsanleitung

Sony

Sony WSFV11 Gebrauchs- und Wartungshandbuch

Sony

Sony SU-MD1 Bedienungs- und Wartungsanleitung

Sony

Sony SU-WL450 Service-Handbuch

Sony

Sony SU-43T4 Bedienungsanleitung

Sony

Sony SU-WL850 Service-Handbuch

Sony

Sony SU-WL450 Service-Handbuch

Sony

Sony ACY-RK2 Bedienungsanleitung

Sony

Sony BKM-38H Bedienungsanleitung

Sony

Sony SU-PF2 Bedienungsanleitung

Sony

Sony SU-RS11M Bedienungsanleitung

Sony

Sony RHT-G1550 Bedienungsanleitung

Sony

Sony SU-WL450 Bedienungsanleitung

Sony

Sony RHT-G2000 - Home Theater Built-in Sound Rack... Bedienungsanleitung

Sony

Sony Bravia XBR-55HX950 Bedienungsanleitung

Sony

Sony SU-W200 Bedienungsanleitung

Sony

Sony YT-ICB33V Bedienungsanleitung

Sony

Sony SU-560 Bedienungsanleitung

Sony

Sony SU-ES29G Bedienungsanleitung

Sony

Sony SU-52NX1 Bedienungsanleitung

Sony

Sony SU-46NX1 Gebrauchs- und Wartungshandbuch

Sony

Sony SU-WL11 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung