Sony DNW-A25WS Bedienungsanleitung

DIGITAL VIDEOCASSETTE RECORDER

DNW-A25WS

DNW-A25WSP

INSTALLATION MANUAL

1st Edition

Serial No. 15001 and Higher: DNW-A25WS

Serial No. 45001 and Higher: DNW-A25WSP

DNW-A25WS/A25WSP

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen.Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

DNW-A25WS/A25WSP

Table of Contents

Manual Structure

Purpose of this manual .............................................................................................. 2

Related manuals......................................................................................................... 2

1. Installation

1-1. Installation Procedure..................................................................................1-1

1-2. Supplied Accessories ..................................................................................1-1

1-3. Operating Conditions ..................................................................................1-1

1-4. Power Supply ..............................................................................................1-2

1-5. Installation Space ........................................................................................1-3

1-6. Connectors/Cables.......................................................................................1-4

1-7. Signal Inputs and Outputs ...........................................................................1-5

1-8. Settings for Internal Switches/Slit Lands....................................................1-8

1-8-1. AU-249 Board ............................................................................1-8

1-8-2. RE-150 Board.............................................................................1-9

1-9. Setup Extended Menu ...............................................................................1-10

1-10. Settings for External Editors .....................................................................1-11

1-10-1. Time Code Settings for Recorder.............................................1-11

1-10-2. VTR Constant Settings for External Editors ............................1-11

1-10-3. System Phase Adjustment ........................................................1-11

1-10-4. Setup Menu Setting of ITEM-701............................................1-11

1-11. Removing/Reattaching the Plug-in Boards...............................................1-12

1-12. How to Take Out the Cassette Whose Tape is Slacked ............................1-14

Appendix A Setting Check Sheet

2DNW-A25WS/A25WSP

Manual Structure

Purpose of this manual This manual is the installation manual of digital videocassette recorder

DNW-A25WS/A25WSP.

This manual is intended for use by trained system and service engineers, and

provides the information that is required to install (environment, connection infor-

mation, initial setting, etc.) .

Related manuals Besides this “installation manual”, the following manuals are available for digital

videocassette recorder DNW-A25WS/A25WSP.

.Operation Manual (Supplied with the unit.)

This manual is necessary for application and operation (and installation) of the unit.

.Maintenance Manual (available on request)

Volume-1 : Service Instruction

Volume-2 : Parts List, Diagrams

These manuals describe the maintenace and service information (service over-

view, adjustments, board layouts, schematic diagrams, detailed parts list, etc.) for

this unit. If these manuals are required, please contact your local Sony Sales

Office/Service Center.

.Protocol Manual of Remote (9-pin) Connector (available on request)

This manual explains the protocol for controlling the VTR via the RS-422A (9-pin

serial remote). If this manual is required, please contact your local Sony Sales

Office/Service Center.

.BKNW-225 Maintenance Manual (Supplied with the BKNW-225)

This manual describes the spare parts list and the exploded view for the service

parts of the docking kit BKNW-225, that is used when the two DNWs are cou-

pled.

1-1

DNW-A25WS/A25WSP

1-3. Operating Conditions

1-4. Power Supply

1-6. Connectors/Cables

1-7. Signal Inputs and Outputs

1-8. Settings for Internal

Switches/Slit Lands

1-9. Setup Extended Menu

1-10. Settings for External Editors

Start

Determination of

installation place

Unpacking

*Connection

*Initial setup

*Operation check

End

1-5. Installation Space

Installation

Section 1

Installation

1-1. Installation Procedure

Installation procedure of this unit is shown on the follow-

ing flowchart.

Refer to each section about detail of each flow.

The operation manual is also reqruired to do *-marked

flow.

1-2. Supplied Accessories

Cap, BNC ........................................................................ 11

Cap, DC OUT .................................................................... 2

Cap, XLR (F)..................................................................... 2

Cap, XLR (M) ................................................................... 5

Cap, DUST ........................................................................ 1

Shoulder belt assembly...................................................... 1

Rear panel cover ................................................................ 1

Operation manual .............................................................. 1

Installation manual ............................................................ 1

After installation, be sure to use the supplied caps for

protecting unused connectors.

1-3. Operating Conditions

Do not block an air vent. If ventilation is not enough, the

unit may be damaged due to increase the internal tempera-

ture of the unit.

.Do not shove the unit into cramped place with poor

ventilation.

.Be sure to make cleaning if a cooling fan is covered with

dust.

.Replace a cooling fan periodically.

.Do not place the unit on a longhaired carpet.

.Do not cover the unit with cloth.

Good air circulaiton is essential to prevent internal heat

build-up. Place the unit in location with sufficient air

circulation.

Do not block the ventilation holes of the cabinet and the

front and rear panels.

Operating temperature: 0dC to 40dC

Operating humidity: 25% to 80% (Condensation not

allowed)

Storage temperature: _20dC to 60dC

Locations to avoid:

.Areas where the unit will be exposed to direct sunlight

of any other strong lights.

.Areas near heat sources.

.Dusty areas or areas subject to vibration.

.Areas with strong magnetic field.

.Areas with much electrical noise.

.Areas with much static electricity.

.Areas that is impossible to find a specified room for

installation.

(Refer to Section “1-5. Installation Space” .)

.Areas windtight.

1-2 DNW-A25WS/A25WSP

DC IN

AC adaptor

AC-DN2A/DN2B

AC adaptor

AC-550

Lithium-ion battery

BP-L90A/L60A

Ni-cd battery

BP-90A

Battery adaptor

DC-L90

Ni-cd battery

BP-90A

Battery adaptor

DC-210

DC OUT

AC adaptor

AC-DN2A/DN2B

DNW-A25WS/A25WSP

Rear View

Battery terminal

(DC cable)

1-4. Power Supply

The unit works either on AC current (using the AC adaptor) or battery. When repairing or checking the

unit, however, AC-operation is recommended.

Power Voltage: DC 11 to 17 V

Power Consumption : 65 W

.The AC adaptor AC-DN1 cannot be used to derive power.

.The AC adaptor AC-DN2A/DN2B can supply power to two VTRs simultaneously. The AC-DN2 with

serial No.11001 or higher can supply, too. If the above adaptor is used, power on the VTRs and load

cassettes in turn allowing for an inrush current.

.While the unit is battery-operated, the remaining battery capacity is displayed on the sub menu indica-

tor. When the battery is nearly dead, the WARNING indicator on the side of the LCD monitor will

blink. For details, refer to the operation manual supplied with the unit.

Connection example (when operating two VTRs)

1-3

DNW-A25WS/A25WSP

150

349

120d

R217

145

157

331

443

210

230

461

1-5. Installation Space

To avoid an injury, do not install the unit on rickety table.

Ventilation and Installation Space for Servicing

.Do not block an exhaust section and an air vent (rear panel).

.In order to make a unit with good ventilation, ensure sufficient clearance around the unit.

.In order to ensure a workspace, more than 20 cm behind the unit is required.

Outside Dimensions

Unit : mm

1-5. Installation Space

1-4 DNW-A25WS/A25WSP

1-6. Connectors/Cables

Connection made with the connector panels during installation or service, should be made with the

connectors or complete cable assemblies specified in the following list, or equivalent parts.

Panel indication Connection connector (Sony P/N) Connection cable (Sony P/N)

VIDEO REF IN Plug, BNC (1-564-742-11) RG-59B/U cable

VIDEO INPUT

VIDEO OUTPUT

TC IN

TC OUT

SDI IN Plug, BNC (1-564-742-11) BNC coaxial cable

SDI OUT (1-791-456-11: supplied with BKNW-225) or

BELDEN 8281 cable (Maximum cable length: 200 m)

AUDIO INPUT XLR 3P, MALE (1-508-084-00) –––––––

AUDIO OUTPUT XLR 3P, FEMALE (1-508-083-00) –––––––

MONITOR OUTPUT

DC IN XLR 4P, FEMALE (1-508-362-00) DC power cord (1-551-577-00:supplied with AC-550/

550CE)

DC OUT Plug 4P MALE (1-566-425-11) –––––––

REMOTE Plug 9P MALE (1-560-651-00) 9P remote control cable

Shell, Junction 9P (1-561-749-00) (1-783-089-12: supplied with BKNW-225) or

RCC-5G(5 m)/10G(10 m)/30G(30 m)

AUX Plug 6P MALE (1-560-078-00) –––––––

HEADPHONES JM-60 stereo phone plug –––––––

(Separately available)

1-6. Connectors/Cables

1-5

DNW-A25WS/A25WSP

1-7. Signal Inputs and Outputs

Communications Connectors

6REMOTE D-SUB 9P connector x1 (RS-422A interface)

Remote control

![ AUX 6-pin connector x1

Input Connectors

1AUDIO INPUT CH-1/CH-2 XLR 3-pin x2

Analog audio 2 channels

_60 dBu, 0 dBu, +4 dBu selectable, high impedance, balanced

2VIDEO REF.IN BNC x2 (In loop through connection, with 75 Ztermination switch)

External reference video signal (Black burst or composite sync)

40 IRE/0.3 Vp-p, 75 Z, negative sync

3VIDEO INPUT BNC x2 (In loop through connection, with 75 Ztermination switch)

Analog composite video 1.0 Vp-p, 75 Z, negative sync

!- SDI IN BNC x1

Component digital (270 Mbit/s) SMPTE 259M/ITU-R BT.656

8TC IN BNC x1

Time code 0.5 to 18.0 Vp-p, 10 kZ, unbalanced

!\ DC IN XLR 4-pin x1

DC +11 to 17 V

BATTERY IN 5-pin terminal x1

(on battery sub panel) Lithium-ion battery interface

REMOTE

TC IN

TC OUTSDI OUT

SDI IN DC OUT

DC-IN

AUX

VIDEOAUDIO INPUT

REF.

AUDIO OUTPUT

ONOFF

75Z

ONOFF

CH-1

1/3

+48V

+4dBu_60 0

ONOFF

CH-2

+48V +4dBu_60 0

INPUT OUTPUT

2(SUPER)

OFF

75Z

2/4 MONITOR OUTPUT

R L

9 !/ != ![ !\!]!-

2 3 4 6 875

< Connector panel >

1-7. Signal Inputs and Outputs

1-6 DNW-A25WS/A25WSP

Output Connectors

4VIDEO OUTPUT 1 BNC x1

Analog composite video 1.0 Vp-p, 75 Z, negative sync

5VIDEO OUTPUT 2 BNC x1 (Character superimpose enabled)

Analog composite video 1.0 Vp-p, 75 Z, negative sync

9AUDIO OUTPUT 1/3, 2/4 XLR 3-pin x2

Analog audio 2 channels (CH-1/CH-2 or CH-3/CH-4 selectable by sub menu)

+4 dBm (standard) (600 Zload), low impedance, balanced

!/ MONITOR OUTPUT R/L XLR 3-pin x2

Analog audio channel (AUDIO OUTPUT enabled by selecting sub menu)

+4 dBm (standard) (600 Zload), low impedance, balanced

!= SDI OUT BNC x2

Component digital (270 Mbit/s) SMPTE 259M/ITU-R BT.656

!] TC OUT BNCx1

Time code 1.0 Vp-p ±3 dB (75 Zload), unbalanced

7DC OUT 4-pin connector x1 (for BVR-3)

DC +12 V (+11 to 17 V), 0.5 A (max)

HEADPHONES JM-60 stereo phone jack

(at the front) Analog audio

up to _20 dBu adjustable (8 Zload), unbalanced

6REMOTE (9P Female)

Pin No. Signal

1 GND

2 RM TX (_)

3 RM RX (_)

4 GND

5 PRIORITY

6 GND

7 RM TX (+)

8 RM RX (+)

9 GND

!\ DC IN (4P Male)

Pin No. Signal

1 GND

2NC

3NC

4 EXT DC

(External View)

1-7. Signal Inputs and Outputs

Andere Handbücher für DNW-A25WS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sony Aufnahmegeräte Handbücher

Sony

Sony SLV-KS1 - Video Cassette Recorder Bedienungsanleitung

Sony

Sony XDCAM PDW-U1 Bedienungsanleitung

Sony

Sony TC-366 Einrichtungshandbuch

Sony

Sony 3-270-589-12 (1) Bedienungsanleitung

Sony

Sony TC-42 Bedienungsanleitung

Sony

Sony CFD-RS60CP Bedienungsanleitung

Sony

Sony SEQ-V902 Bedienungsanleitung

Sony

Sony PFV-D10 Bedienungsanleitung

Sony

Sony DRE-S777 Bedienungsanleitung

Sony

Sony XDCAM PDW-HR1 Bedienungsanleitung

Sony

Sony PFV-L10 Bedienungsanleitung

Sony

Sony TCD-D3 Bedienungsanleitung

Sony

Sony ICD-B25 Operating Instructions (primary... Bedienungsanleitung

Sony

Sony DSR-DU1 Bedienungsanleitung

Sony

Sony CDR-W33 Bedienungsanleitung

Sony

Sony HXCU-FB70 Bedienungsanleitung

Sony

Sony IFB-12A Bedienungsanleitung

Sony

Sony BDX-N1000 Bedienungsanleitung

Sony

Sony DMW-S01NL Bedienungsanleitung

Sony

Sony DPS-V77 Bedienungsanleitung

Sony

Sony SRW5800/2 Bedienungsanleitung

Sony

Sony SEG-2550 Bedienungsanleitung

Sony

Sony DMX-R100 Bedienungsanleitung

Sony

Sony DPS-V77 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch