Sony 600TVL O.S.D. WDR SERIES Bedienungsanleitung

SERVICE MANUAL

1/3” SONY DSP COLOR CCD CAMERA

600TVL O.S.D. WDR SERIES

V.4B_W_M

The serial number of this product may be found

on the bottom of the unit.

You should note the serial number of this unit in

the space provided and retain this instruction as a

permanent record of your purchase to aid

identification in the event of theft.

Model No.

SerialNo.

▲Before attempting to connect this product, please read and keep this

manual for future use.

Safety Warning

1. Do not open the cover, it may cause electric shock.

Ask a qualified service person for maintenance when you encounter any

problems.

2. Install the camera away from TV, radio transmitter, magnet, electric

motor, transformer, audio speakers because the magnetic fields

generated from above devices will distort the video image.

3. Place this camera on a solid base. Install the camera away from

stoves or other heat generating devices as the high temperature could

cause deformation, discoloration or other damages to the camera.

Install the camera at where the temperature range does not exceed

-10°C to 50°C (14°F to 122°F)

4. Do not expose and operate the camera in the rain and humid areas.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is interned to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

①

5. Use only soft dry cloth to clean the camera. Also use lens tissue or

cotton tipped applicator and ethanol to clean the CCD sensor and

camera lens.

6. When the camera is not in use, put the cover cap on the lens mount.

Please do not touch the surface of CCD by bare hand.

Introduction

This OSD series CCD camera introduces a new level of high picture quality

through the digital signal processing LSI’s technology for advanced video

surveillance. It provides the most reliable and accurate color picture in the

security industries.

Main Features

zColor camera with SONY 1/3” Super HAD II CCD sensor.

zEmploys Digital Signal Processor (DSP) chip-set for image control.

zUltra high resolution 600TVL (B/W 650TVL).

zHigh sensitivity CCD enables a clear image even in 0.01Lux.

zControlled by OSD (On Screen Display) menu.

zProgrammable AE / AWB / GAMMA processing.

z2DNR (2D Noise Reduction), digital WDR (Wide Dynamic Range).

zMotion detection, mirror, privacy mask.

zParking line guide display, lens shading correction.

zBLC (Back Light Compensation), HLC (Highlight Compensation).

zAuto DPC (Dead Pixel Compensation).

②

Highlight Compensation

Lens Shading Compensation

Wide Dynamic Range

Parts Names & Components

Auto Iris Function

Hex Screwdriver

Auto Iris Plug

C-Mount Ring (Option)

Manual

DC DRIVE

Pin 1 (Red) Drive -

Pin 2 (N.C) Drive +

Pin 3 (White) Damp +

Pin 4 (Black) Damp -

Power LED Selection & setting buttons

Hole to fix lens

Auto iris connector

Screw the auto iris lens on CS mount

Plug in auto iris connector

③

Installation Instructions

(1) Remove the cap from the lens mount.

(2) Select the C mount lens (with mount ring) or CS mount lens.

(3) Screw and fasten the lens into the lens mount.

(4) Connect the video output wire between monitor and camera through

75ohm type coaxial cable.

(5) Connect the power cord input.

(6) When monitor shows the picture, please adjust the focus and iris of the

lens to obtain the best image according to the following procedures:

‧ Choose objects at a distance about 5 ~ 10 meter away.

‧ Loosen the mount lens fixing screw (use L wrench), if necessary.

‧ Turn the lens and the mount together until image is clear.

‧ Screw the mount to camera.

(7) Fix camera to the bracket, if necessary

Switch Definition

SET button

Press to display the menu. In the menu, this button functions as “ENTER”.

UP & DOWN buttons

Press to select the item of menu.

LEFT & RIGHT buttons

Press to change the item value.

④

LEFT SET RIGHT

button button button

button

DOWN

button

Menu Operation

‧ Press the SET button to display the menu on screen.

‧ Press the UP or DOWN button to select the item.

‧ The selected item will be highlighted.

‧ Press the LEFT or RIGHT button to change mode.

‧ The ENTER symbol means there is a sub-menu. Press the SET button to enter

to the sub-menu.

‧ Select the EXIT item and press the SET button to finish setting.

SETUPMENU

LENS

To select the lens mode depending on the lens used:

‧ MANUAL When manual iris lens is used.

‧ DC When auto iris lens that requires a DC drive signal is used.

‧ VIDEO Not available.

EXPOSURE

¾SHUTTER

To change the shutter setting and speed based on the environment.

‧ AUTO After an immobile brightness value is set, the shutter speed

will adjust automatically to achieve the value.

‧ FLK Select when flickering occurs on the screen due to an

Imbalance between illumination and frequency. Under this

mode, the shutter speed is NTSC: 1/100; PAL: 1/120.

‧ Fixed speed adjustable: 1/50; 1/250; 1/500; 1/1000; 1/2000; 1/4000; 1/5000;

1/10000; 1/100000.

¾BRIGHTNESS Value 0~255 adjustable.

¾AGC (Auto Gain Control)

Enable this function to heighten the brightness signal automatically.

‧ HIGH LOW; MIDDLE adjustable.

‧ OFF To disable this function.

¾DWDR (Digital Wide Dynamic Range)

When there is a very strong backlight behind the object, more than theAGC

function can handle, enable this function to achieve a clear image of the

background as well as the object.

‧ ON To enable this function. Value 0~63 adjustable.

‧ OFF To disable this function.

WHITE BAL. (White Balance)

‧ ATW1 Auto Tracking White Balance. The white balance will adjust

continually according to the color temperature of the object. The

⑤

range of color temperature is 2,000°K~9,500°K.

‧ ATW2 Auto Tracking White Balance. The white balance will adjust

continually according to the color temperature of the object. The

range of color temperature is 2,000°K~10,500°K.

‧ AWCÆSET Auto White Balance Control. Push to set white balance

according to the color temperature of the background.

‧ MANUAL The manual adjustment mode enables finer adjustment of ATW.

Set the color temperature to MANUAL and then increase or

decrease the RED (0~255) and BLUE (0~255) color values

while monitoring the color changes on the object. Or, chose the

INDOOR; OUTDOOR mode for quick adjustment.

BACKLIGHT

When there is strong backlight behind the object, enable this function to achieve a

clear image of the background as well as the object.

‧ BLC Back Light Compensation. AREA1; AREA2 adjustable.

‧ HLC Hightlight Compensation. ALL DAY; NIGHT ONLY adjustable.

‧ OFF To disable this function.

DAY&NIGHT

‧ COLOR Common mode.

‧ AUTO Automatically changes between color mode under bright light

environment and B/W mode under low light environment. Set

the value of D-N LEVEL (Day to Night 0~216); N-D LEVEL

(Night to Day 0~206); D-N DELAY (Day to Night 1~30 SEC);

N-D DELAY (Night to Day 1~30 SEC) to define the changing

condition and time.

‧ B/W Stay in B/W mode for clear and better visibility image under

low light environment. BURST (ON; OFF); IR SMART (ON;

OFF); IR LEVEL (HIGH; LOW) adjustable.

‧ EXT Control day & night mode by external device (if connected).

DPC (Dead Pixel Correction)

Cover the lens then press SET button to delete dead pixel on screen.

SPECIAL MENU

CAM TITLE (Camera Title)

‧ ON To name the camera title.

‧ OFF Not active.

MOTION (Motion Detection)

When the object on screen is moving, the camera will detect the changes and

display a warning on screen.

‧ ON AREA1~AREA4 adjustable. 0~255 DEGREE adjustable.

‧ OFF Not active.

⑥

PRIVACY (Privacy Zone)

Cover the areas you do not wish to appear on screen.

‧ ON AREA1~AREA8 adjustable. 0~15 COLOR adjustable.

‧ OFF To disable this function.

PARK. LINE (Parking Line)

‧ ON Parking line guide display on screen.

‧ OFF To disable this function.

IMAGE ADJ.

¾LENS SHAD. (Lens Shading Compensation)

‧ ON Counter lens shading on the four corners of monitor screen.

‧ OFF To disable this function.

¾2DNR (2D Noise Reduction)

Enable this function to reduce the noise at low light environment. This function

enables the camera to use a higher AGC level to electronically enhance the

sensitivity of the camera in low light environment (higher AGC, more noise).

‧ ON To enable this function.

‧ OFF To disable this function.

¾MIRROR

‧ ON To see mirror image on monitor screen.

‧ OFF To disable this function.

¾FONT COLOR

FONT color (0~15); ID&TITLE (0~15) adjustable.

¾CONTRAST Value 0~255 adjustable.

¾SHARPNESS Value 0~255 adjustable.

¾DISPLAY

‧ CRT PED LEVEL (0~63); COLOR GAIN (0~255) adjustable.

‧ LCD GAMMA (0.05~1.00); PED LEVEL (0~63); COLOR GAIN

(0~255) adjustable.

‧ USER GAMMA (0.05~1.00); PED LEVEL (0~63); COLOR GAIN

(0~255) adjustable.

¾NEG. IMAGE (Negative Image)

‧ ON To show negative image on monitor screen.

‧ OFF To disable this function.

LANGUAGE

Supports ENGLISH; 中文 (Simple Chinese).

VERSION To show the version of this camera.

RESET Select for factory reset.

⑦

Specification

MODEL OSD WDR OSD WDR with ICR (True DAY & NIGHT)

IR OPTICAL FILTER Built-in anti-aliasing IR-cut filter Built-in anti-aliasing IR-pass (850nm) filter

PICK-UP DEVICE Sony 1/3" Super HAD II High Resolution CCD

EFFECTIVE PICTURE

ELEMENTS (H*V)

NTSC: 768*494

PAL: 752*582

SIGNAL PROCESSOR D.S.P. (Digital Signal Processor)

RESOLUTION 600 TV Lines (B/W 650 TV Lines)

MIN. ILLUMINATION 0.01Lux / F1.2

S/N RATIO More than 52 dB

POWER SUPPLY DC12V; AC90~260V Switching Power; DC12V/AC24V Dual Power

CONTROL O.S.D. (On Screen Display)

LENS MOUNT C / CS Mount

AUTO IRIS DC Drive Auto Iris Lens

AUTO ELECTRONIC

SHUTTER

NTSC: 1/60s~1/100,000s (AES ON); 1/60s (AES OFF)

PAL: 1/50s~1/110,000s (AES ON); 1/50s (AES OFF)

VIDEO OUTPUT 1 Vp-p Composite Video / 75 ohm Load

POWER CONSUMPTION 3.5W (Max.)

OPERATING TEMP. -10°C~50°C (14°F~122°F)

MENU OPERATION

SETUP MENU

LENS: MANUAL – DC – VIDEO

EXPOSURE:

¾SHUTTER: AUTO – FLK – 1/50 – 1/250 – 1/500 – 1/1000 – 1/2000 – 1/4000 – 1/5000 –

1/10000 – 1/100000

¾BRIGHTNESS: 0~255

¾AGC: LOW – MIDDLE – HIGH – OFF

¾DWDR: ON (0~63) – OFF

WHITE BAL.: ATW1 – ATW2 – AWCÆSET – MANUAL: RED (0~255); BLUE (0~255) –

INDOOR – OUTDOOR

BACKLIGHT: BLC: AREA1; AREA2 – HLC: ALL DAY; NIGHT ONLY – OFF

DAY&NIGHT: COLOR – AUTO – B/W – EXT

DPC

RESET

SPECIAL MENU

CAM TITLE: ON – OFF

MOTION: ON:AREA1~AREA4; DEGREE (0~255) – OFF

PRIVACY: ON: AREA1~AREA8; COLOR (0~15) – OFF

PARK. LINE: ON – OFF

IMAGE ADJ.:

¾LENS SHAD.: ON – OFF

¾2DNR: ON – OFF

¾MIRROR: ON – OFF

¾FONT: FONT (0~15); ID&TITLE (0~15)

¾CONTRAST (0~255)

¾SHARPNESS (0~255)

¾DISPLAY: CRT: PED LEVEL (0~63); COLOR GAIN (0~255)

LCD: GAMMA(0.05~1.00); PED LEVEL (0~63); COLOR GAIN (0~255)

USER: GAMMA (0.05~1.00); PED LEVEL (0~63); COLOR GAIN (0~255)

¾NEG. IMAGE: ON – OFF

LANGUAGE: ENGLISH – S.CHINESE

VERSION

V.4B_W_M

Appendix

Installation Manual for Special Application: License Plate Recognition

1. A 5-55mm or other more than 10X suitable vari-focal auto iris lens is

recommended. Connect regulated DC12V power supply to the power input at the

rear panel of camera. Connect BNC video cable to the video output at the rear

panel of camera.

2. Fix the camera on the bracket. Adjust the viewing angle of camera according to

the below recommendations:

For capturing the front plate no.: Setting the camera at a 15° or less vertical

angle will achieve the best performance. Do not let the vertical angle exceed

20° (Figure 1).

For capturing the back plate no.: The vertical angle must not exceed 30°

(Figure 2).

Capture zone distance: Between 15~20 meters from the camera.

3. Adjust the zoom of the vari-focal lens. The picture width should not exceed 1.5

traffic lanes at the capture zone.

ÆEnter SETUP menu and select “DC” under LENS options.

4. In order to ensure a clear image under different light conditions, adjust the

settings once during the daytime and once during the nighttime is recommended

to achieve optimal results.

15~20M

<20°

[Figure 1]

0°

<30°

15~20M

[Figure 2]

0°

Inhaltsverzeichnis

Andere Sony Sicherheitskamera Handbücher

Sony

Sony Ipela Hybrid SNC-Zm550 Bedienungsanleitung

Sony

Sony 1/3" DSP COLOR CAMERA Bedienungsanleitung

Sony

Sony DXC-9100P Bedienungsanleitung

Sony

Sony IPELA SNC-CH220 Bedienungsanleitung

Sony

Sony XCD-SX910CR/X710CR Bedienungsanleitung

Sony

Sony EVI-D100 (NTSC) Bedienungsanleitung

Sony

Sony SNCVB600 Bedienungsanleitung

Sony

Sony SNC-VB635 Bedienungsanleitung

Sony

Sony FCB-EX980S, FCB-EX980SP, FCB-E Bedienungsanleitung

Sony

Sony Ipela SNC-DH210 Bedienungsanleitung

Sony

Sony SNC-CH115 Bedienungsanleitung

Sony

Sony SNC-RS46N Bedienungsanleitung

Sony

Sony SSC-M183 - CCTV Camera Bedienungsanleitung

Sony

Sony SNC-RH124 Bedienungsanleitung

Sony

Sony DynaView SSC-DC593 Bedienungsanleitung

Sony

Sony Ipela SNC-XM637 Bedienungsanleitung

Sony

Sony XC-ST50 Bedienungsanleitung

Sony

Sony SST-6420 Bedienungsanleitung

Sony

Sony EFFIO IRDOME3XVF PRO Bedienungsanleitung

Sony

Sony Vaio PCGA-UVC11A Bedienungsanleitung

Sony

Sony FCBEX490E Bedienungsanleitung

Sony

Sony FCBIX47C Bedienungsanleitung

Sony

Sony Ipela SNC-CS50N Bedienungsanleitung

Sony

Sony SNC-RH124 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung