Sony SDX-400C Bedienungsanleitung
4-649-283-03(2)
2000 Sony Corporation
AIT Drive
SDX-400 Series
SDX-410 Series
User’s Guide
2
Contents
Introduction .......................................4
Product Features........................4
Precautions ................................5
Installation .........................................7
SCSI Connection/Setting the
SCSI ID .................................7
Option Switches (DIP Switch) ..8
Mounting Holes........................9
Remodeling from 5.25" Model
to 3.5" Model .......................12
Orientation...............................13
Operation .........................................14
Location of 3 LEDs .................14
LED Indication for
Drive Status .........................15
Drive Operation.......................16
Emergency Tape Removal
Procedure .............................17
Interface Implementation.................20
Supported SCSI Messages ......20
Supported SCSI Commands....20
Specification ....................................21
Product Specifications.............21
Third Party Support Contacts
(In the USA) ...............................23
Sony Contacts ..................................25
This document contains proprietary
information which is protected by
copyright.
All rights reserved. No part of this
document may be photocopied,
reproduced or translated to another
language without prior written consent
of Sony.
The information contained in this
document is subject to change without
notice.
SONY MAKES NO WARRANTY
OF ANY KIND WITH REGARD TO
THIS DOCUMENT.
Sony shall not be liable for error
contained herein, indirect, special,
incidental or consequential damages in
connection with the furnishing,
performance or use of this document.
VORSICHT
Diese Ausrüstung erfüllt die
Europäischen EMC-Bestimmungen für
die Verwendung in folgender /
folgenden Umgebung(en):
• Wohngegenden
• Gewerbegebiete
• Leichtindustriegebiete
(Diese Ausrüstung erfüllt die
Bestimmungen der Norm EN55022,
Klasse B.)
3
SDX-400 Tape Drive
The Sony SDX-400 series drive is a high capacity data storage device using
Advanced Intelligent tape (AIT) technology. The SDX-400 series drive
achieves high data reliability through Read-After-Write, an additional level
of Error Correction Code, and other features.
The Sony SDX-400 series drive stores data on tape using a standard format
called AIT (Advanced Intelligent Tape) and ALDC formats.
4
Introduction
Product Features
* Assuming a 2.6 : 1 compression ratio.
(The compression ratio varies according to the type of data.)
• Supported Format : AIT-1
• Burst Transfer Rate
– 12 MB/s Asynchronous
– 40 MB/s Synchronous
• Large 10 MB Buffer Memory
• 3.5” Standard Height, 5.25” Half Height
• Embedded SCSI Interface
(ULTRA/WIDE and LVD/SE model (SDX-400C) or HVD model (SDX-
410C) are available)
• Supports Variable or Fixed Record Length
• Supports SCSI Disconnection/Arbitration
• Frame Rewrite Function
• Three levels of Error Correction Code (ECC)
• High Speed search (120 times normal Read/Write speed)
• Random Read, Append Write
Data Capacity
Transfer Rate (sustained)
SDX-400 series
35 GB uncompressed (with AIT-1 230 m tape)
91 GB compressed*(with AIT-1 230 m tape)
4 MB/s uncompressed
5
Precautions
Installation
Avoid placing the drive in a location subject to:
– high humidity
– high temperature
– mechanical shock and vibration
– direct sunlight
Operation
• Do not move the drive while it is operating. It may cause malfunction.
• Avoid exposing the drive to sudden changes from a low to high in
temperature. This may cause water condensation to collect inside the
drive. If the ambient temperature should suddenly rise while the drive is
turned on , wait at least one hour before turning on the drive. If you
attempt to operate the drive immediately after a sudden increase in
temperature, a malfunction may occur.
• Turning off the power to the drive while it is writing to tape may cause
the tape to become unreadable. All previously negotiated parameters will
be lost, whenever power to the drive is cycled.
Transportation
• Keep the original packing materials to facilitate transportation of the
drive.
• Always remove the tape before moving the drive. After removing the
drive from the computer, repack the drive into its original packing.
6
Notice of SCSI Termination
The SDX-400C conforms to the Microsoft PC97 standard which requires
the internal (naked) drive to be terminated with an external terminator.
Microsoft PC97 SCSI requirements
SCSI peripherals must not terminate the bus. Both internal and external
cable ends are instead terminated by plug-in connectors.
Terminato
r
68p cable
Host Computer Wide SCSI
This drive
Example of SCSI set-up
7
Installation
SCSI Connection/Setting the SCSI ID
SCSI 68pin Connector
5 V
Power Connector
1234
GND GND 12 V
Disable
Enable
Parity
Note :
=
= CLOSED/Jumper
Don’t care
OPEN/Jumper not
installed
Parity Disable
No Connection
SCSI ID 3
SCSI ID 2
SCSI ID 1
SCSI ID 0
Jumpers
SCSI ID
SCSI ID
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
2
1
0
P.D.
N.C.
3
Parity Disable Jumper
Parity check function can be disabled by Jumper. Parity check is disabled
while left end jumper is installed. Parity generate function is always
enabled.
8
Option Switches (DIP Switch)
DIP Switch Positions
ON
12345678
DIP Switch
1 Reserved (OFF)
2 Reserved (OFF)
3 Reserved (OFF)
4 Reserved (OFF)
5 Terminator Power (ON)
6 Reserved (OFF)
7 DC Control (1) (ON)
8 DC Control (2) (OFF)
Data Compression Control DIP switch
Data compression can be selected by DIP switches. Data compression is
enabled while position 7 [DC Control (1)] is ON. Control by host can be
disabled when position 8 [DC Control (2)] is ON.
9
Mounting Holes
For 3.5" Standard Height (SDX-400C)
6-M3 (depth
2.5 mm (0.10 in) max.)
70.0±0.3 mm
(2.76±0.01 in)
42.0±0.3 mm
(1.65±0.01 in)
31.0±0.3 mm
(1.22±0.01 in)
7.0±0.5 mm (0.28±0.02 in) 155.0±0.5 mm (6.10±0.02 in) 7.6±0.5 mm (0.30±0.02 in)
94.0±0.3 mm (3.70±0.01 in)
101.6±0.5 mm (4.00±0.02 in)
90.0±0.3 mm (3.54±0.01 in)
60.0±0.3 mm (2.36±0.01 in)
21.0±0.3 mm
(0.83±0.01 in)
5.0±0.3 mm
(0.20±0.01 in)
41.2±0.5 mm
(1.62±0.02 in)
3-M3 (depth
2.5 mm (0.10 in) max.)
95.5 mm (3.76 in) 8.45 mm (0.333 in)
5.53±0.5 mm
(0.218±0.02 in)
7.4±0.5 mm
(0.29±0.02 in)
10
For 3.5" Standard Height (SDX-410C)
92.71mm (3.65 in)
(depth 0.10 in max.)
6-M3 (depth 2.5 mm)
(depth 0.10 in)
4.7±0.5 mm
(0.185 in)
8 mm
(0.315 in)
94±0.3 mm
(3.70 in)
101.6±0.5 mm
(4.00 in)
5±0.3 mm
(0.20 in)
41.2±0.5 mm
(1.62 in)
90±0.3 mm
(3.54 in)
60±0.3 mm
(2.36 in)
21±0.3 mm
(0.83 in)
70±0.3 mm
(2.76 in)
42±0.3 mm
(1.65 in)
31±0.3 mm
(1.22 in)
170±0.5 mm
(6.69 in) 7.6±0.5 mm
(0.30 in)
7.4±0.5 mm
(0.29 in)
3-M3 (depth 2.5 mm max.)
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Sony Lagerung Handbücher
Sony
Sony MSA-8A Bedienungsanleitung
Sony
Sony MicroVault USM-L Bedienungsanleitung
Sony
Sony HD-EG5 Bedienungsanleitung
Sony
Sony ODS-L100E Bedienungsanleitung
Sony
Sony LIB-162 Bedienungsanleitung
Sony
Sony MSX-M1GN Bedienungsanleitung
Sony
Sony CSM-100BS Bedienungsanleitung
Sony
Sony MS-MT16G Bedienungsanleitung
Sony
Sony SDX-420C Bedienungsanleitung
Sony
Sony StorStation AITe200-UL Bedienungsanleitung
Sony
Sony SDT-S11000 Bedienungsanleitung
Sony
Sony MSAC-US40 - MemoryStick Flash Memory Card USB 2.0... Bedienungsanleitung
Sony
Sony SF Series Bedienungsanleitung
Sony
Sony MSX-M4GS Bedienungsanleitung
Sony
Sony DDS-4 Bedienungsanleitung
Sony
Sony Memory Stick PRO MSX-4GN Bedienungsanleitung
Sony
Sony MicroVault USM1GJ Bedienungsanleitung
Sony
Sony HDPS-M10 - Data Storage Wallet Bedienungsanleitung
Sony
Sony MSA-16A Bedienungsanleitung
Sony
Sony CDL1100 Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung