Sony 26-483-01 Gebrauchsanweisung

Extron • System 8/10 PLUS • User’s Manual • P/N 68-428-01 Rev. E

Sony LCD Compatible Installation Configuration and Connections

SYSTEM 8/10 Plus

PROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANT

INSTALLATION INSTRUCTIONS

THIS KIT HAS BEEN SHIPPED WITHTHE FOLLOWING COMPONENTS:

Kit Type: SONY LCD compatible

Included Communications Adapter(s):

Quantity Part Number Description

1 26-483-01 ADP, IR COMM

1 26-473-01 ADP, UNV, “E”

THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING

COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS

MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS

INDICATED BY THE “✔”IN THE “Config as”COLUMN. IF YOUR PROJECTOR MODEL

DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER

WITH THE CORRECT SETTINGS.

PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND

SIGNAL CONNECTION INSTRUCTIONS.

THIS SWITCHER HAS BEEN CONFIGURED FOR: SONY LCD VPL-X600,

VPL-X2000U

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 45678910Adapter

✔Sony VPL-X600 1 0 5 3 J2 ↑↓↑↓↑↓↓ ↓↑↓26-483-01

✔Sony VPL-X2000U 1 0 5 3 J2 ↑↓↑↓↑↓↓ ↓↑↓26-483-01

Sony RS-232 0 0 E 8 J2 ↓↓↑↓↑↓↓ ↓↑↓26-473-01

Sony PX Series 1 0 E 8 J2 ↓↓↑↓↑↓↓ ↓↑↓26-473-01

Page1

Extron •System 8/10 PLUS •User’s Manual •P/N 68-428-01 Rev. E

Sony LCD Compatible Installation Configuration and Connections

Sony LCD VPL-X600 Projector Configuration

Verify that the System 8/10 PLUS is already configured for the Sony LCD VPL-

X600 projector. The general setup is explained on page 3-4 and the switch

settings for the projector are repeated below.

1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS

front panel. See bottom of page 3-3. The label on the back of the access cover

also has the configuration information.

__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS

to verify that the main power is OFF; also turn the projector power OFF.

2. Set the switches as follows:

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

✔Sony VPL-X600 1 0 5 3 J2 ↑↓ ↑ ↓↑↓ ↓ ↓

¯↑↓ 26-483-01

_RS5 is for RGB switching

delay. See page 3-4 for

more information on switch

functions.

3. Use a grease pencil (or other rub-off marker) to mark the space on the label next

to “Sony LCD”.

4. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a master/slave system, set #3 and #5 to the up position and

the others down. See illustration to the left.

Use the illustration on the next page to do the following steps.

5. Verify that the IR Comm Adapter is configured correctly (refer to the

IR Comm

Adapter User’s Guide

). Connect the 3.5 mm male plug end of the supplied

cable into the “OUT”jack of the IR Comm Adapter. Connect the other end of the

cable into the “CONTROL S IN”port of the projector. If a hardwired remote or

host controller is being implemented, connect that device to the “IN”jack of the

IR Comm Adapter.

6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the IR

Comm Adapter to the 15-pin HD “Projector Control”port located on the rear

panel of the System 8/10 PLUS.

______ Secure the screws on all D connectors.

7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to “INPUT

A”of the projector. For S-Video or Composite Video input, use the “VIDEO IN”

projector connectors.

8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

Configured For:

RS-232

34567891012

SW15 DIP Switch

RS5 RS2

RS2

RS1

RS3

RS4

RS1

RS3 RS4

Page2

Extron •System 8/10 PLUS •User’s Manual •P/N 68-428-01 Rev. E

Sony LCD Compatible Installation Configuration and Connections

9. Return System 8/10 PLUS and projector to normal operation.

Sony LCD VPL-X600 Projector Connections

Use the illustration below when connecting the System 8/10 PLUS to a Sony

VPL-X600 projector. Refer to Sony documentation to continue the installation.

_ You cannot input S-Video and Composite Video sources simultaneously on this Sony model.

_ If the installation includes looping (master/slave) switchers, see Chapter 5.

If Video Loop Back is part of the installation, see pages 2-10 and 2-11.

Page3

CC 50'

15-Pin HD

15-Pin 9-Pin

Female

IR Comm Adapter

26-483-01

○○○○○○

○○ ○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○

○○○○○○○○

See note above

○○○○○○○○○○○

Hardwired remote/

host controller

Cable 26-485-01

Extron •System 8/10 PLUS •User’s Manual •P/N 68-428-01 Rev. E

Sony LCD Compatible Installation Configuration and Connections

Sony LCD VPL-X2000U Projector Configuration

Verify that the System 8/10 PLUS is already configured for the Sony LCD VPL-

X2000U projector. The general setup is explained on page 3-4 and the switch

settings for the projector are repeated below.

1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS

front panel. See bottom of page 3-3. The label on the back of the access cover

also has the configuration information.

__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS

to verify that the main power is OFF; also turn the projector power OFF.

2. Set the switches as follows:

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

✔Sony VPL-X2000U 1 0 5 3 J2 ↑↓ ↑ ↓↑↓ ↓ ↓

¯↑↓ 26-483-01

_RS5 is for RGB switching

delay. See page 3-4 for

more information on switch

functions.

3. Use a grease pencil (or other rub-off marker) to mark the space on the label next

to “Sony LCD”.

4. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a master/slave system, set #3 and #5 to the up position and

the others down. See illustration to the left.

Use the illustration on the next page to do the following steps.

5. Verify that the IR Comm Adapter is configured correctly (refer to the

IR Comm

Adapter User’s Guide

). Connect the 3.5 mm male plug end of the supplied

cable into the “OUT”jack of the IR Comm Adapter. Connect the other end of the

cable into the “CONTROL S IN”port of the projector. If a hardwired remote or

host controller is being implemented, connect that device to the “IN”jack of the

IR Comm Adapter.

6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the IR

Comm Adapter to the 15-pin HD “Projector Control”port located on the rear

panel of the System 8/10 PLUS.

______ Secure the screws on all D connectors.

7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to “INPUT

A”of the projector. For S-Video or Composite Video input, use the “VIDEO IN”

projector connectors and refer to the notes on the next page.

8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

Configured For:

RS-232

34567891012

SW15 DIP Switch

RS5 RS2

RS2

RS1

RS3

RS4

RS1

RS3 RS4

Page4

Extron •System 8/10 PLUS •User’s Manual •P/N 68-428-01 Rev. E

Sony LCD Compatible Installation Configuration and Connections

9. Return System 8/10 PLUS and projector to normal operation.

Sony LCD VPL-X2000U Projector Connections

Use the illustration below when connecting the System 8/10 PLUS to a Sony

VPL-X2000U projector. Refer to Sony documentation to continue the installation.

_ You cannot input S-Video and Composite Video sources simultaneously on this Sony model.

_ The projector’s Input Select buttons (Video and Select) allow you to select

either RGB/Composite video or RGB/S-video. See the illustration below and

refer to your Sony documentation.

_ If the installation includes looping (master/slave) switchers, see Chapter 5.

If Video Loop Back is part of the installation, see pages 2-10 and 2-11.

Page5

IR Comm Adapter

26-483-01

○○ ○○○○

○○○○○○○○○○○

Hardwired remote/

host controller

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Cable 26-485-01

Input Select

(see notes above)

CC 50'

15-Pin HD

9-Pin

Female

○○○○○○○○○○○○○○○○○○○

See notes above

○○○○○○○○○○○

○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Extron •System 8/10 PLUS •User’s Manual •P/N 68-428-01 Rev. E

Sony LCD Compatible Installation Configuration and Connections

Sony RS-232 Projector Configuration

Verify that the System 8/10 PLUS is already configured for a Sony RS-232

projector. The general setup is explained on page 3-4 and the switch settings for

the projector are repeated below.

1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS

front panel. See bottom of page 3-3. The label on the back of the access cover

also has the configuration information.

__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS

to verify that the main power is OFF; also turn the projector power OFF.

2. Set the switches as follows:

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

Sony RS-232 0 0 E 8 J2 ↓↓ ↑ ↓↑↓ ↓ ↓

¯↑↓ 26-473-01

_RS5 is for RGB

switching delay. See

page 3-4 for more

information on switch

functions.

3. Use a grease pencil (or other rub-off marker) to mark the space on the label next

to “Sony RS-232”.

4. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a master/slave system, set #3 and #5 to the up position and

the others down. See illustration to the left.

Use the illustration on the next page to do the following steps.

5. Connect the Comm Adapter to the “RS-232C/RS-422A”port. Connect the CC-

50' (or CC-100') cable from the 9-pin male connector of the Comm Adapter to

the 15-pin HD “Projector Control”port located on the rear panel of the System 8/

10 PLUS. Set the projector’s RS-232C/RS-422A switch to the RS-232C position.

______ Secure the screws on all D connectors.

6. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to “INPUT

A”of the projector. For S-Video or Composite Video input, use the “VIDEO IN”

projector connectors.

7. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

8. Return System 8/10 PLUS and projector to normal operation.

Page6

Configured For:

RS-232

34567891012

SW15 DIP Switch

RS5 RS2

RS2

RS1

RS3

RS4

RS1

RS3 RS4

Extron •System 8/10 PLUS •User’s Manual •P/N 68-428-01 Rev. E

Sony LCD Compatible Installation Configuration and Connections

Sony RS-232 Projector Connections

Use the illustration below when connecting the System 8/10 PLUS to a Sony

RS-232 projector. Refer to Sony documentation to continue the installation.

_ If the installation includes looping (master/slave) switchers, see Chapter 5.

If Video Loop Back is part of the installation, see pages 2-10 and 2-11.

Page7

CC 50'

15-Pin HD

9-Pin

Female

9-Pin Male

Com Adapter

26-473-01

Composite video

S-video

RGBHV

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Note: Set switch to RS-232C

○○○○○○○○

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sony Schalten Handbücher

Sony

Sony MVS-6520 Bedienungsanleitung

Sony

Sony DMX-SW1 - Bravia Input Link Bedienungsanleitung

Sony

Sony BZPS-8001 Bedienungsanleitung

Sony

Sony HDS-7100 Bedienungsanleitung

Sony

Sony BKDS-7017 Bedienungsanleitung

Sony

Sony SB-V60S - Auto Switcher AV Selector Bedienungsanleitung

Sony

Sony HKS-5810M Bedienungsanleitung

Sony

Sony DVS-7150 Bedienungsanleitung

Sony

Sony XVS-9000-C Bedienungsanleitung

Sony

Sony MFS-2000-C Bedienungsanleitung

Sony

Sony DMX-SW1 - Bravia Input Link Bedienungsanleitung

Sony

Sony MVS-6000 Bedienungsanleitung

Sony

Sony DFS-700A Bedienungsanleitung

Sony

Sony MCS-8M Bedienungsanleitung

Sony

Sony DVS-7200A Bedienungsanleitung

Sony

Sony UH-1000 Bedienungsanleitung

Sony

Sony MKS-2010 Bedienungsanleitung

Sony

Sony MFS-2000-C Bedienungsanleitung

Sony

Sony MVS-8000X System Bedienungsanleitung

Sony

Sony SB-V60S Bedienungsanleitung

Sony

Sony BRS-200 Bedienungsanleitung

Sony

Sony XA-U40D Bedienungsanleitung

Sony

Sony BVS-3200CP Bedienungsanleitung

Sony

Sony MVS-8000 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung