Sony WRT-847A Bedienungsanleitung
i
Operating Instructions
Mode d'emploi
Bedienungsanleitung
Manual de instrucciones
2000 Sony Corporation
3-205-009-03 (1)
WRT-847A/WRT-847B
UHF Synthesized
Transmitter Unit
GB
FR
DE
ES
ii
Owner’s Record
The model and serial numbers are located at the rear of the
unit. Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony
dealer regarding this product.
Model No. WRT-847A/WRT-847B Serial No.
Notice for customers in the U.S.A.
Use of Sony wireless devices is regulated by the Federal
Communications Commission as described in Part 74
subpart H of the FCC regulations and users authorized
thereby are required to obtain an appropriate license.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.
iii
Notice for customers in Canada:
Use of Sony wireless devices is regulated by the Industry
Canada as described in their Radio Standard Specification
RSS-123.
A licence is normally required. The local district office of
Industry Canada should therefore be contacted. When the
operation of the device is within the broadcast band, the
licence is issued on no-interference, no-protection basis with
respect to broadcast signals.
Operation of this device is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Avis pour les clients au Canada:
L’usage des appareils sans-fil Sony est réglé par l’Industrie
Canada comme décrit dans leur Cahier des Normes
Radioélectriques CNR-123.
Une licence est normalement requise. Le bureau de
l’Industrie Canada doit être contacté. Lorsque l’opération de
l’appareil est dans les limites de la bande de radiodiffusion, la
licence est émanée sur la base de non-interférence, non-
protection avec les signaux de radiodiffusion.
L’utilisation de cet appareil est soumise aux deux conditions
suivantes : (1) cet appareil ne peut causer d’interférences, et
(2) cet appareil doit accepter toutes les interférences, y
compris les interférences capables de provoquer un
fonctionnement indésirable de l’appareil.
iv
Notice for customers in Europe
Spécifications particulières pour les consommateurs européens
Hinweis für Kunden in Europa
Aviso para los usuarios en Europa
U.K. 854.125 - 862 MHz
Germany 798 - 822 MHz
Norway 800 - 820 MHz
Luxembourg 800 - 830 MHz, 854.125 - 862 MHz
Belgium 854.125 - 862 MHz
Denmark 800.100 - 819.900 MHz
France 470 - 830 MHz
Italy 800 - 820 MHz
Sweden 800 - 820 MHz
Switzerland 800 - 820 MHz
Finland 800 - 814 MHz
Iceland 800 - 814 MHz
Austria 774 - 790 MHz
Netherland 774 - 782 MHz
Hereby, Sony Corporation, declares that this WRT-847B is
in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Note:
In some countries additional frequency bands may be used
with the agreement of the national authority.
Sony Corporation déclare par la présente que ce WRT-847B
est conforme aux exigences fondamentales et aux autres
dispositions applicables de la Directive 1999/5/CE.
Note :
Des bandes de fréquence supplémentaires peuvent être
utilisées dans certains pays, avec l'accord des autorités
nationales.
Hiermit erklärt die Sony Corporation, daß das Modell
WRT-847B die grundlegenden Anforderungen und sonstigen
relevanten Bestimmungen der Richtlinie 1999/5/EU erfüllt.
Hinweis:
In einigen Ländern können mit dem Einverständnis
nationaler Behörden weitere Frequenzbereiche verwendet
werden.
v
Por la presente, Sony Corporation, declara que este
WRT-847B cumple con los requisitos esenciales y otras
disposiciones pertinentes de la Directiva 1999/5/EC.
Nota:
En algunos países, es posible utilizar bandas de frecuencias
adicionales con el consentimiento de las autoridades
nacionales.
Hinweis für Kunden in der Österreich:
Vor Inbetriebnahme ist die individuelle Genehmigung der
lokalen Behörden für das Telekommunikationsspektrum
erforderlich.
Note for customers in Switzerland:
Before use, a request of concession for a wireless
microphone (Frequency Class 3) has to be submitted to
Bakom.
Note concernant les utilisateurs en Suisse:
Une demande de concession de microphone sans fil
(fréquence classe 3) doit être présentée au Bakom avant
d'utiliser l'appareil.
Hinweis für Kunden in der Schweiz:
Vor Inbetriebnahme ist eine Konzessionsanforderung für ein
drahtloses Mikrofon (Frequenzklasse 3) bei Bakom
einzureichen.
Note for customers in Finland:
To own and use, it is necessary to obtain an individual
licence of the Telecommunications Administration
Center.
Hinweis für Kunden in der Luxemburg:
Vor Inbetriebnahme eines Geräts müssen die Frequenzen
gegebenenfalls nach den geltenden Vorschriften vor dem
Gebrauch von der “ILT” zugewiesen werden.
Nota per i clienti in Italia
L’uso del prodotto sul territorio italiano è soggetto alle
regolamentazioni del Codice Postale e delle
Telecomunicazioni art. 334.
Hinweis für Kunden in der Deutschland:
Vor Inbetriebnahme muß bei der zuständigen Außenstelle
der Regulierungsbehörde (Reg TP) eine Kanalzuweisung
beantragt werden.
vi
Note for customers in Norway:
Using this transmitter with 50 mW RF output power requires
the frequency license.
Note for customers in Belgium:
Using this transmitter with 50 mW RF output power is not
allowed. Be sure to set the RF output power to 10 mW.
Note concernant les utilisateurs en Belgique:
L’emploi de ce transmetteur avec une puissance de sortie RF
de 50 mW n’est pas autorisé. Bien régler la puissance de
sortie RF à 10 mW.
Hinweis für Kunden in Belgien:
Der Einsatz des Senders mit einer HF-Ausgangsleistung von
50 mW ist verboten. Betreiben Sie den Sender ausschlieβlich
mit einer HF-Ausgangsleistung von 10 mW.
1(GB)
English
English
GB
• The unit is designed for use in ambient temperature range
of 0°C to 50°C (32°F to 122°F).
• Do not place the unit on or near heat sources, such as
lighting equipment, power amplifiers, or in a place subject
to direct sunlight or excessive moisture. In such places,
the external finish or internal parts of the unit may be
damaged.
• If the unit is used in a very humid or dusty place or in a
place subject to expose to an active or corrasive gas, clean
its surface as well as the connectors with a dry, soft cloth
soon after use.
Lengthy use of the unit in such places or not cleaning it
after its use in such places may shorten its life.
• When cleaning the unit, never use organic solvents such as
thinners or benzine, which will damage the finish of the
unit.
• Using the unit with wet hands may cause trouble in the
unit.
• The unit has been factory adjusted precisely. Do not
tamper with its internal parts or attempt to repair it.
• Make sure to use two LR6 (size-AA) alkaline batteries.
• Make sure the poles of the batteries match the + and –
markings in the battery holder.
• Remove the batteries when the unit will not be used for a
long period of time.
• Do not attempt to recharge the alkaline batteries.
• Do not dispose of the batteries in fire. Do not disassemble
or short-circuit the batteries.
Precautions
Table of Contents
Precautions................................................................ 1
Introduction ............................................................... 2
Features ..........................................................2
Parts Identification.................................................... 4
Power Supply ............................................................ 7
Settings ...................................................................... 8
Initiating Setting Mode ..................................8
Changing the Transmitting Channel ..............9
Changing the Audio Gain Setting ................10
Resetting the Accumulated
Battery Use Time Indication ..................11
Changing the Compander Time Constant....11
Changing the RF Output Power ...................12
Troubleshooting ...................................................... 13
Specifications.......................................................... 15
Error Messages ....................................................... 16
2(GB)
Introduction
Coupling with the CU-F780, CU-G780, CU-E700, CU-E672
or CU-F117 Sony Microphone Capsule Unit, the WRT-847A/
847B UHF-synthesized transmitter unit makes up a UHF-
synthesized wireless microphone to be used in a UHF-
synthesized wireless microphone system.
For vocal concentration, operate the WRT-847A/847B in
conjunction with the WRR-802A/850A, MB-806A with
WRU-806A UHF Synthesized Tuner. For vocal and
interview use, operate the WRT-847A/847B in conjunction
with the WRR-805A/855A UHF Synthesized Tuner.
The microphone/transmitter and tuners of the wireless
microphone system are classified by frequency band.
A 24 MHz frequency band (a 14 MHz frequency band:
model available in Australia) is assigned to each
microphone/transmitter and tuner model.
In building up a UHF wireless microphone system, be sure
to combine a microphone/transmitter and a tuner having the
same TV channel number.
Features
Selectable microphone capsules
To make up suitable wireless microphones for your use, five
microphone capsule units are available as optional
accessories. The capsule units for the WRT-847A/847B are;
CU-F780 Super Cardioid Dynamic Microphone Unit
CU-G780 Super Cardioid Dynamic Microphone Unit
for Live Vocal Performance
CU-E700 Super Cardioid Electret Condenser
Microphone Unit
CU-E672 Hyper Cardioid Electret Condenser
Microphone Unit (Short-shotgun)
CU-F117 Omni-directional Dynamic Microphone Unit
The capsule unit can be mounted simply by screwing it into
the transmitter.
Phase Locked Loop (PLL) synthesized system
The WRT-847A/847B features a refined phase locked loop
(PLL) synthesizer circuit.
Wide dynamic range and low noise
The compander (compressor/expander) system enables
transmission over a wide dynamic range with minimum
noise. The compander time constant is selectable to get the
optimum sound quality of the individual microphone
capsule.
3(GB)
Selectable RF output
The RF output power can be adjusted to high (50 mW) or
low (10 mW) to match the environment where it will be
used; to obtain a wide service area, set this to 50 mW, and
when using the transmitter in a simultaneous multi-channel
system, set it to 10 mW.
Highly reliable audio gain level adjustment
With an adjustable range of –12 dB to +9 dB in 3 dB steps,
the built-in input level volume reduces signal distortion
during the input of excessively strong audio signals. It can
raise the input gain during too low audio input.
POWER switch with holding function
The POWER switch can be locked in the ON position to
protect against accidental power cutoffs.
Powered by readily available battery type
The built-in, high-efficiency DC-DC converter provides
about eight hours of continuous and stable operation with
two LR6 (size-AA) alkaline batteries.
Low-battery notification on the unit and the tuner
When the transmitter batteries are low, the transmitter sends
a warning to the WRR-802A/805A/850A, MB-806A with
WRU-806A in the form of “Battery status information.”
This information is sent to the WRR-802A/805A/850A,
MB-806A with WRU-806A about one hour before the
batteries go dead to allow the batteries to be safely replaced.
When the WRR-802A/805A/850A, MB-806A with
WRU-806A receive this information, the LED and the
LCD1) display on tuner panel start to flash.
LCD1) read-out of various information
The transmitter's LCD1) display shows the current channel
number, frequency, audio gain, compander time constant,
RF output settings and residual battery power.The
accumulated battery use time is also indicated (in one-
minute increments) to allow precise monitoring of battery
use.
Automatic saving of channel, audio gain and RF
output settings
All channel, audio gain, compander time constant, and RF
output settings are automatically saved when the transmitter
is turned off, thus eliminating the need to make the same
settings again the next time you use the transmitter.
Tone signal-incorporated RF carrier signal
The transmitter sends an RF carrier signal that incorporates
a tone signal to enable any tuner with a tone squelch circuit
to pick out only the target audio signal.
Notes on simultaneous multi-channel
operation
When operating two or more transmitters simultaneously in
a multi-channel system, please note the following.
• Set the RF output power of the transmitters to 10 mW.
• Keep the transmitters separated from each other by a
distance of at least 30 cm (1 foot).
• Keep the transmitters at least 3 meters (10 feet) away from
the receiving antenna.
1)LCD: Liquid-crystal display
.............................................................................................................................................................................................................................................................
4(GB)
Parts Identification
1Microphone capsule unit (not supplied)
Mount the microphone capsule unit (CU-F780, CU-G780,
CU-E700, CU-E672 or CU-F117) securely.
See the instruction manual supplied with your microphone
capsule unit for mounting.
2Liquid-crystal display (LCD)
AAF (audio input) indication
Lights whenever an audio signal stronger than the reference
level is received.
BRF (antenna output) indication
Lights during signal transmission from the antenna.
CPower (RF power) indication
Shows the RF power setting.
See “Changing the RF Output Power” on page 12.
AB DC
E
AF RF BATT
1
In the figure, the CU-F780 capsule unit (not supplied)
is mounted on the WRT-847A/847B as an example.
2
3
4
5
6
7
Channel indication Eshows
that of the CE62 model as
an example.
Andere Handbücher für WRT-847A
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere Sony Sender Handbücher
Sony
Sony AIR-SA17Ti Bedienungsanleitung
Sony
Sony UTX-B1 Bedienungsanleitung
Sony
Sony AIR-SA17Ti Marketing Bedienungsanleitung
Sony
Sony TMR-BT10 - Bluetooth Wireless Audio... Bedienungsanleitung
Sony
Sony MDR-RF875R Bedienungsanleitung
Sony
Sony WRT-860A Bedienungsanleitung
Sony
Sony TMR-PJ2 Bedienungsanleitung
Sony
Sony TMR-BT10 - Bluetooth Wireless Audio... Bedienungsanleitung
Sony
Sony ATS-SW10Ti Marketing Bedienungsanleitung
Sony
Sony TMR-BT10 - Bluetooth Wireless Audio... Bedienungsanleitung
Sony
Sony TMR-BT8iP - Bluetooth Wireless Transmitter Montage- und Bedienungsanleitung
Sony
Sony DWT-P01 Bedienungsanleitung
Sony
Sony WLA-NS7 Bedienungsanleitung
Sony
Sony TMR-PJ1 Bedienungsanleitung
Sony
Sony WRT-822A Bedienungsanleitung
Sony
Sony WRT-847A Bedienungsanleitung
Sony
Sony UTX-B03HR Bedienungsanleitung
Sony
Sony DWTP01N/14 Bedienungsanleitung
Sony
Sony TMR-RF960R Bedienungsanleitung
Sony
Sony IFV-FX1 Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
