Sophos XG 105w Bedienungsanleitung

Quick Start Guide

XG 105(w)/115(w)/125(w)/135(w) Rev. 3

For more information about your device, scan the QR code or visit

www.sophos.com/get-started-xg

1. Before Deploying

Congratulations on the purchase of your Sophos XG device. This Quick Start Guide describes in short steps how to connect your

device and explains how to open the web-based Admin Console from your administration PC. The Admin Console allows you to

conﬁgure every aspect of the device.

Before you begin please conﬁrm that you have a working Internet connection and make sure you have the account information

available that was provided by your ISP.

What is included in the box

Micro USB cable

RJ45 Ethernet cable

Power Adapter (region speciﬁc)

This Quick Start Guide and Security NotesXG 105(w)/115(w)/125(w)/135(w)

XG 105w/115w - 2 antennas;

XG 125w/135w - 3 antennas

Quick Start Guide XG 105(w)/115(w)/125(w)/135(w) Rev. 3

Device Images: Front and Back*

* The displayed front image is of the XG 115 and XG 135 device and the back is of the XG 115w and XG 135w.

1 x COM

(RJ45)

2 x

USB 2.0

1 x Micro

USB

4 x GbE

copper port

1 x GbE SFP

(shared)

1 x

HDMI

Power

Supply

Connector for optional 2nd

redundant power supply

2 x external antenna

(XG 105w and XG 115w only)

Status LEDs

(w-model has additional Wi-Fi LED)

1 x COM

(RJ45)

3 x external

antenna

(XG 125w and

XG 135w only)

2 x

USB 2.0

8 x GbE

copper port

Power

Supply

Connector for optional 2nd

redundant power supply

1 x Micro

USB

1 x

HDMI

Expansion bay

(shown with optional

module incl. 2 antennas)

1 x GbE

SFP

Status LEDs

(w-model has additional Wi-Fi LED)

XG 125(w)/135(w)

XG 105(w)/115(w)

Quick Start Guide XG 105(w)/115(w)/125(w)/135(w) Rev. 3

2. Mount & connect the device

Mount the antennas (for wireless models only)

Connect the provided antennas to the connectors on the back

of your appliance and align them in a vertical position.

Connect the ports to the internal and external networks

1. Connect the Port 1/LAN port via a hub or switch to the internal network. For this

purpose, use the RJ45 Ethernet cable provided. Note that your Administration PC

must also be connected to this network.

2. Connect Port 2/WAN to the external network. The connection to the WAN

depends on the type of Internet access.

Please note: on XG 105(w)/115(w) the SFP port is shared with RJ45 Ethernet Port 4

and takes precendence over the RJ45 port in case you connect cables to both ports

at the same time.

The XG devices are shipped with the following default settings:

Ethernet Port IP Address Zone

1172.16.16.16/255.255.255.0 LAN

2DHCP WAN

Admin Console Username Admin Console Password CLI Console Password

admin admin admin

Default Gateway DNS proxy DHCP service

DHCP Enabled Enabled

Mount the appliance to the rack

If you want to mount the device within a rack please use the optionally available

rackmount kit for this device.

Internet

e.g.,

DSL modem

Internal network

admin client PC

XG Appliance

Switch

Port 2/

WAN

Port 1/

LAN

Quick Start Guide XG 105(w)/115(w)/125(w)/135(w) Rev. 3

3. Power Up the Device

Connect the power adapter(s) and turn on the device

Connect the provided power adapter to connector 1 on the back of the device. In

order to increase redundancy you can connect an optionally available second power

adapter of the same type to power connector 2.

Turn the device on. The power switch is on the back of the device and is placed next

to the power connection.

During boot up the Status LED on the front will blink green. Once the device has

booted completely the Status LED will turn to solid green.

4. Connect your Administration PC

Administration PC connection properties:

Use the settings below to conﬁgure your (PC/Laptop) network interface:

ÌIP address: 172.16.16.2

ÌNetmask: Enter 255.255.255.0

ÌDefault Gateway: Enter the IP address of the device’s

internal network card (Port 1/LAN): 172.16.16.16

ÌDNS Server: Enable this option and enter the IP address of

the internal network card (Port 1/LAN): 172.16.16.16

Connect your PC/Laptop to Port 1/LAN port of the device:

Start the browser and enter the management IP address of the device’s LAN port

that your PC is connected to: https://172.16.16.16:4444 (Port 1)

Username: admin Password: admin

Quick Start Guide XG 105(w)/115(w)/125(w)/135(w) Rev. 3

5. Setup the device

a) Register the Device

If you have not previously registered your device with your Sophos ID, you will see a

registration screen. The device requires Internet connectivity for it to be registered

with your Sophos ID. You can adjust the network settings of the device’s interfaces

by clicking “Basic Setup” so that the device can connect to the Internet.

After clicking “Register Device”, you are redirected to the Sophos.com. If you already

have a Sophos ID, enter your login credentials under “Sign in with your Sophos ID”.

If you are a new user, sign up for a Sophos ID by entering the details under “Create

Sophos ID”.

Click “Continue” to complete the registration process. Please wait while the process

completes – it will take a few seconds. After successful registration, you will see

a screen with the message, “Your device is now registered”. Please note that you

should proceed with the next step i.e. “Synchronize License” only after the device is

successfully registered.

b) Synchronize License

Click “Initiate License Synchronization” to fetch license information from Sophos

onto the device. After synchronization, you will see a screen with the message,

“Synchronization with server was successful”.

c) Start Network Conﬁguration

After successful synchronization, choose “Click Here” on the “Welcome” screen

to start your initial device conﬁguration. Use the Network Conﬁguration Wizard

to select the deployment mode (Bridge/Gateway) for your device, change the

interface(s) IP addresses, default gateway, DNS settings and Date/Time Zone to

match your local network settings.

d) Device LED Status

LEDs on each RJ45 Ethernet connector

ACT/LNK

(Left LED)

Green Constantly 1. The Ethernet port is receiving power.

2. Good connection between the Ethernet port

and hub.

Flashing The adapter is sending or receiving network data.

The frequency of the ﬂashes varies with the

amount of trafﬁc.

Off 1. The adapter and switch are not receiving power.

2. No connection between both ends of network.

3. Network drivers have not been loaded or do not

function correctly.

Network Conﬁguration Wizard

Start

Skip

Secure your enterprise with

Sophos integrated internet security

Welcome

To your Sophos Device

To get started register your device below. Until you register you may only access

and edit settings in “Basic Setup” and your device will remain unactivated.

XXXXXXXXXXXXXXX

Basic Setup

Serial Number

Device Management

Quick Start Guide XG 105(w)/115(w)/125(w)/135(w) Rev. 3

Speed

(Right

LED)

Amber On The Ethernet port is operating at 1,000 Mbps

Green On The Ethernet port is operating at 100 Mbps

Off The Ethernet port is operating at 10 Mbps

LEDs on SFP connector

ACT/LNK

(Left LED)

Green Constantly 1. The SFP connector is receiving power.

2. Good connection between the SFP connector

and hub.

Flashing The adapter is sending or receiving network data.

The frequency of the ﬂashes varies with the amount

of trafﬁc.

Off 1. The adapter and switch are not receiving power.

2. No connection between both ends of network.

3. Network drivers have not been loaded or do not

function correctly.

Speed

(Right

LED)

Amber On The Ethernet port is operating at 1,000 Mbps

LEDs on front

Storage Blue Flashing SSD drive is being accessed

Status Green Constantly Normal operation

Flashing Device is booting up or shutting down

Red Constantly SSD or boot failure

Flashing General error (please contat support)

Wiﬁ Green On Wiﬁ is active

Off Wiﬁ is inactive

Power 1 Green Constantly Power adapter 1 in normal operation

Red Constantly Power adapter 1 failed or disconnected

Power 2 Green Constantly Power adapter 2 in normal operation

Red Constantly Power adapter 2 failed or disconnected

6. Support and Documentation

For more information and technical support, please visit www.sophos.com/en-us/

support or contact your local Sophos reseller.

1. Vorbereitung

Herzlichen Glückwunsch zum Kauf dieser Sophos XG Appliance. Diese Kurzanleitung beschreibt schrittweise, wie Sie die

Appliance verbinden, und erläutert, wie Sie über Ihren Administrations-PC die webbasierte Admin Console öffnen. Über die Admin

Console können Sie jeden Aspekt der Appliance konﬁgurieren.

Bevor Sie beginnen, vergewissern Sie sich, dass Sie mit dem Internet verbunden sind und die Kontodaten vorliegen, die Sie von

Ihrem ISP erhalten haben.

Verpackungsinhalt

Für weitere Informationen zu Ihrer Appliance scannen Sie den QR-Code oder gehen Sie auf

www.sophos.com/get-started-xg

Micro USB-Kabel

RJ45 Ethernet-Kabel

Netzadapter (regionenspeziﬁsch)

Diese Kurzanleitung und SicherheitshinweiseXG 105(w)/115(w)/125(w)/135(w)

XG 105w/115w – 2 Antennen,

XG 125w/135w – 3 Antennen

Kurzanleitung XG 105(w)/115(w)/125(w)/135(w) Rev. 3

1 x COM

(RJ45)

2 x

USB 2.0

1 x Micro-

USB

4 x

Kupferport

GbE

1 x GbE

SFP

(geteilt)

1 x

HDMI

Stromversorgung

Anschluss für optionale

zweite redundante

Stromversorgung

2x externe Antenne

(nur XG105w und XG115w)

Abbildungen der Appliance: Vorder- und Rückseite*

XG 125(w)/135(w) Rev. 3

XG 105(w)/115(w) Rev. 3

1 x COM

(RJ45)

3x externe

Antenne

(nur XG125w

und XG135w)

2 x

USB 2.0

8 x

Kupferport

GbE

Stromversorgung

Anschluss für optionale

zweite redundante

Stromversorgung

1 x Micro-

USB

1 x

HDMI

Erweiterungsschacht

(abgebildet mit

optionalem Modul

einschl. 2Antennen)

1 x GbE

SFP

* Die Abbildung der Vorderseite bezieht sich auf die XG 115 und XG 135 Appliance und die der Rückseite auf die XG 115w und XG 135w.

Status-LEDs

(w-Modell hat zusätzliche WiFi-LED)

Status-LEDs

(w-Modell hat zusätzliche WiFi-LED)

Kurzanleitung XG 105(w)/115(w)/125(w)/135(w) Rev. 3

2. Appliance montieren und verbinden

Antennen montieren (nur bei Wireless-Modellen)

Stecken Sie die mitgelieferten Antennen in die entsprechenden Anschlüsse auf der

Rückseite Ihrer Appliance ein und bringen Sie sie in eine vertikale Position.

Ports mit den internen und externen Netzwerken verbinden

1. Verbinden Sie Port 1/LAN-Port über einen Hub oder Switch mit dem internen

Netzwerk. Verwenden Sie hierzu das beiliegende RJ45 Ethernet-Kabel. Beachten

Sie, dass Ihr Administrations-PC ebenfalls mit diesem Netzwerk verbunden sein

muss.

2. Verbinden Sie Port 2/WAN mit dem externen Netzwerk. Die Verbindung zum

WAN hängt von der Art des Internetzugangs ab.

Bitte beachten Sie: Bei XG 105(w)/115(w) wird der SFP-Port mit RJ45 Ethernet-

Port 4 geteilt und hat Vorrang vor dem RJ45-Port für den Fall, dass Sie Kabel mit

beiden Ports gleichzeitig verbinden.

Für die XG Appliances sind werkseitig folgende

Standardeinstellungen festgelegt:

Ethernet-Port IP-Adresse

Vertrauenswürdige

Sites

1172.16.16.16/255.255.255.0 LAN

2DHCP WAN

Benutzername Admin

Console

Kennwort Admin Console Kennwort CLI Console

admin admin admin

Standard-Gateway DNS-Proxy DHCP-Dienst

DHCP Aktiviert Aktiviert

Appliance im Rack montieren

Wenn Sie die Appliance in einem Rack montieren möchten, verwenden Sie das für

dieses Gerät optional erhältliche Rackmontage-Kit.

Internet

z.B.

DSL-Modem

Internes

Netzwerk

Administrations-

Client-PC

XG Appliance

Switch

Port 2/

WAN

Port 1/

LAN

Kurzanleitung XG 105(w)/115(w)/125(w)/135(w) Rev. 3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Sophos Firewall Handbücher

Sophos

Sophos SG 310 Bedienungsanleitung

Sophos

Sophos XG 550 Bedienungsanleitung

Sophos

Sophos SG 650 Bedienungsanleitung

Sophos

Sophos WS500 Bedienungsanleitung

Sophos

Sophos XGS 87 Bedienungsanleitung

Sophos

Sophos XGS 4300 Bedienungsanleitung

Sophos

Sophos WS100 Bedienungsanleitung

Sophos

Sophos XGS 116 Bedienungsanleitung

Sophos

Sophos WS1100 Bedienungsanleitung

Sophos

Sophos XG 750 Bedienungsanleitung

Sophos

Sophos SG 450 Bedienungsanleitung

Sophos

Sophos SG 430 Bedienungsanleitung

Sophos

Sophos SD-RED 60 Bedienungsanleitung

Sophos

Sophos XGS 5500 Bedienungsanleitung

Sophos

Sophos SFM 300 Bedienungsanleitung

Sophos

Sophos SG 550 Bedienungsanleitung

Sophos

Sophos XG 85 Bedienungsanleitung

Sophos

Sophos UTM 120 Bedienungsanleitung

Sophos

Sophos SG 550 Bedienungsanleitung

Sophos

Sophos SG 310 Bedienungsanleitung

Sophos

Sophos SG 450 Bedienungsanleitung

Sophos

Sophos UTM 425 Bedienungsanleitung

Sophos

Sophos XG 86 Bedienungsanleitung

Sophos

Sophos XG 750 Bedienungsanleitung

Beliebte Firewall Handbücher anderer Marken

Cisco

Cisco S190 Bedienungsanleitung

Fortinet

Fortinet FortiGate Voice Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 2300 Bedienungsanleitung

SecureLogix

SecureLogix ETM System Bedienungsanleitung

NETGEAR

NETGEAR ProSafe FVX538 Bedienungsanleitung

Lanner

Lanner FW-8877 Bedienungsanleitung

Huawei

Huawei USG6000 Series Installations- und Betriebshandbuch

H3C

H3C SecPath F5000-AI-15 Bedienungsanleitung

Nexcom

Nexcom DNA 1150 Bedienungsanleitung

Fortinet

Fortinet FortiGate-60 series Bedienungsanleitung

Cisco

Cisco 3110 Handbuch

Draytek

Draytek Vigor2860 Series Bedienungsanleitung

Lanner electronics

Lanner electronics FW-7650 Series Bedienungsanleitung

Swisscom

Swisscom Internet Backup Bedienungsanleitung

SonicWALL

SonicWALL NSa 5700 Bedienungsanleitung

DPtech

DPtech FW1000 SERIES Bedienungsanleitung

FEITIAN

FEITIAN MultiPass FIDO Bedienungsanleitung

EBLOCKER

EBLOCKER PRO Bedienungsanleitung