Sound Magus SE90.2 Bedienungsanleitung

SE90.2 / SE150.2/SE90.4 / SE150.4

SE800.1 / SE1500.1/SE2000.1 / SE3500.1

DSP DIGITAL POWER AMPLIFIERS

OWNER'S MANUAL

FEATURES

Overload, shortcircuit, thermal, low voltage protection

Power Supply Design: Full MOSFET DC-DC PWM Power Supply

Double side FR-4 PCB,High quality SMD components

Delay Time (0-20ms / 0.02ms step) & Delay Time Trim set adjustable;

4 bands Customized EQ with adjustable Q factor;27 bands fixed EQ with

fixed Q factor

Full range Crossover Slope 6dB - 48dB（HP/ BP/ LP）

All settings stored in the amps will be saved as presets for the next turn-

on.

All settings can be saved and upload to software as a preset, convenient to

offer long-distance aids to customers.

Professional software with intuitive user interface,Supporting multiple

operation systems like Windows XP/ vista / Win7, Android & Apple OS

Wireless remote controller to switch 4 settings in real-time

Special WIFI adapter to actualize the wireless communications with

software

4 Settings Memory Stored Function

Built-in Professional DSP circuit

Congratulations on your purchase of a SOUNDMAGUS state-of-the-art

power amplifier with digital signal processing. At SOUNDMAGUS Mobile

Audio we strive to provide some of the latest technology tools that make

the quest for “the perfect tune” so much easier. Our goal was to develop

technologically advanced amplifiers completely adjustable to the acoustics

of each vehicle.

INTRODUCTION

A power amplifier’s performance is only as good as its installation.

Proper installation will maximize the system’s overall performance. It is

recommended that you have our product installed by an authorized

SOUNDMAGUS retailer. However, if you decide to install it by yourself,

please carefully read through this manual and take your time to do a

qualified installation.

RECOMMENDATION

FEATURES

Overload, shortcircuit, thermal, low voltage protection

Power Supply Design: Full MOSFET DC-DC PWM Power Supply

Double side FR-4 PCB,High quality SMD components

Delay Time (0-20ms / 0.02ms step) & Delay Time Trim set adjustable;

4 bands Customized EQ with adjustable Q factor;27 bands fixed EQ with

fixed Q factor

Full range Crossover Slope 6dB - 48dB（HP/ BP/ LP）

All settings stored in the amps will be saved as presets for the next turn-

on.

All settings can be saved and upload to software as a preset, convenient to

offer long-distance aids to customers.

Professional software with intuitive user interface,Supporting multiple

operation systems like Windows XP/ vista / Win7, Android & Apple OS

Wireless remote controller to switch 4 settings in real-time

Special WIFI adapter to actualize the wireless communications with

software

4 Settings Memory Stored Function

Built-in Professional DSP circuit

Congratulations on your purchase of a SOUNDMAGUS state-of-the-art

power amplifier with digital signal processing. At SOUNDMAGUS Mobile

Audio we strive to provide some of the latest technology tools that make

the quest for “the perfect tune” so much easier. Our goal was to develop

technologically advanced amplifiers completely adjustable to the acoustics

of each vehicle.

INTRODUCTION

A power amplifier’s performance is only as good as its installation.

Proper installation will maximize the system’s overall performance. It is

recommended that you have our product installed by an authorized

SOUNDMAGUS retailer. However, if you decide to install it by yourself,

please carefully read through this manual and take your time to do a

qualified installation.

RECOMMENDATION

SE800.1/SE1500.1/SE2000.1/SE3500.1

CONTROLS & FUNCTIONS

SE90.2/SE150.2

SE800.1/SE1500.1

SE2000.1/SE3500.1SE90.2/SE150.2 SE90.4/SE150.4

Connect speakers/subwoofers to these terminals. Be sure to check wire for proper

polarity. Never connect the speaker cables to chassis ground.

123 4

587 6

1. SPEAKERS

587 6

123 4

SE90.4/SE150.4

CONTROLS & FUNCTIONS

the vehicle battery or the positive terminal of an isolated audio system battery.

Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of

2. +12 Volt Power

remote turn on lead of the head unit or signal source.

This terminal turns on the amplifier when (+)12 volt is applied to it . Connect it to the

3.Remote Turn On

stripped of all paint down to the bare metal. Use the shortest distance possible. It is always a

good idea to replace the factory ground at this time with a larger cable equal to the new amplifier

power cable or larger.

CAUTION: Do not connect this terminal directly to the vehicle battery ground terminal or any

other factory ground points.

Connect this cable directly to the frame of the vehicle. Make sure the metal frame has been

4.GND

123 4

587 6

SE800.1/SE1500.1/SE2000.1/SE3500.1

CONTROLS & FUNCTIONS

SE90.2/SE150.2

SE800.1/SE1500.1

SE2000.1/SE3500.1SE90.2/SE150.2 SE90.4/SE150.4

Connect speakers/subwoofers to these terminals. Be sure to check wire for proper

polarity. Never connect the speaker cables to chassis ground.

123 4

587 6

1. SPEAKERS

587 6

123 4

SE90.4/SE150.4

CONTROLS & FUNCTIONS

the vehicle battery or the positive terminal of an isolated audio system battery.

Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of

2. +12 Volt Power

remote turn on lead of the head unit or signal source.

This terminal turns on the amplifier when (+)12 volt is applied to it . Connect it to the

3.Remote Turn On

stripped of all paint down to the bare metal. Use the shortest distance possible. It is always a

good idea to replace the factory ground at this time with a larger cable equal to the new amplifier

power cable or larger.

CAUTION: Do not connect this terminal directly to the vehicle battery ground terminal or any

other factory ground points.

Connect this cable directly to the frame of the vehicle. Make sure the metal frame has been

4.GND

123 4

587 6

PREINSTALLATION

Please prepare sufficiently to layout your car space before installation. We

recommend to have the installation done by an Autho rized SOUNDMAGUS

Dealer.

Please use good insulated power cable to endure longterm above 40A

electronical current. The +12 Volt power cable must be connected with a

fuse in line near 20cm of battery+ terminal. Required current, power

cable and proper external fuse listed as following:

MODEL

CABLE

FUSE

SE800.1

4 #

80 A

SE1500.1

2 - 4 #

120 A

SE2000.1

0 - 4 #

200 A

SE3500.1

0 - 2 #

300 A

SE90.2

8 #

30 A

SE150.2

4 - 8 #

40 A

SE90.4

40 A

SE150.4

4 - 6 #

60 A

4 - 8 #

Please use car audio RCA cables, otherwise it may be disturbed. Keep

these cables as short as possible. To avoid disturbances from your car

electronics, please don`t close the existing car cables when you install

the RCA cables.

Don't expose any cables out of car. Please take care insulated cables to

avoid damaging when cables pass through metal, rubber and plastic

etc. Don't install all cables too tight.

The ground wire should be connected directly with the chassis of your

vehicle which should be metal to metal ground point connection.

The amplifier must be mounted securely at a solid, dry and low vibration

surface in the trunk or passenger area. Fix the amplifier in an open air

area to insure proper heat dissipation.

CONTROLS & FUNCTIONS

SE800.1/SE1500.1

SE2000.1/SE3500.1SE90.2/SE150.2 SE90.4/SE150.4

with a minimum level of 200mV is required for proper operation. The use of high quality twisted

pair cables is recommended to decrease the possibility of radiated noise entering the system.

These RCA input jacks are for use with source units that have RCA outputs. A source unit

5. RCA Input Jacks

The red LED will light up and will be flashing if there is a fault presented to the amplifier.

Please disconnect the amplifier and resolve the fault before reconnecting the amplifier.

7. Alarm Indicator

This LED will light up when amplifier works properly.

8. RUN

WI - FI adapter. Connection amplifier and adapter wap - set crossover and function. Once set

up completed, WI - FI adapter can be pulled out, latest settings will be saved in the amplifier.

6. I/O PORT

PREINSTALLATION

Please prepare sufficiently to layout your car space before installation. We

recommend to have the installation done by an Autho rized SOUNDMAGUS

Dealer.

Please use good insulated power cable to endure longterm above 40A

electronical current. The +12 Volt power cable must be connected with a

fuse in line near 20cm of battery+ terminal. Required current, power

cable and proper external fuse listed as following:

MODEL

CABLE

FUSE

SE800.1

4 #

80 A

SE1500.1

2 - 4 #

120 A

SE2000.1

0 - 4 #

200 A

SE3500.1

0 - 2 #

300 A

SE90.2

8 #

30 A

SE150.2

4 - 8 #

40 A

SE90.4

40 A

SE150.4

4 - 6 #

60 A

4 - 8 #

Please use car audio RCA cables, otherwise it may be disturbed. Keep

these cables as short as possible. To avoid disturbances from your car

electronics, please don`t close the existing car cables when you install

the RCA cables.

Don't expose any cables out of car. Please take care insulated cables to

avoid damaging when cables pass through metal, rubber and plastic

etc. Don't install all cables too tight.

The ground wire should be connected directly with the chassis of your

vehicle which should be metal to metal ground point connection.

The amplifier must be mounted securely at a solid, dry and low vibration

surface in the trunk or passenger area. Fix the amplifier in an open air

area to insure proper heat dissipation.

CONTROLS & FUNCTIONS

SE800.1/SE1500.1

SE2000.1/SE3500.1SE90.2/SE150.2 SE90.4/SE150.4

with a minimum level of 200mV is required for proper operation. The use of high quality twisted

pair cables is recommended to decrease the possibility of radiated noise entering the system.

These RCA input jacks are for use with source units that have RCA outputs. A source unit

5. RCA Input Jacks

The red LED will light up and will be flashing if there is a fault presented to the amplifier.

Please disconnect the amplifier and resolve the fault before reconnecting the amplifier.

7. Alarm Indicator

This LED will light up when amplifier works properly.

8. RUN

WI - FI adapter. Connection amplifier and adapter wap - set crossover and function. Once set

up completed, WI - FI adapter can be pulled out, latest settings will be saved in the amplifier.

6. I/O PORT

4) After The Plastic Cap Is Stick To The Amp, Holding Two Ends Of The Plastic

Caps( As Shown In Figure 3 ) And Push them down to the same horizontal level ( As

Shown In The Figure 3).

Holding both ends of the plastic cap,

push down together with same strength.

Figure 3:

6) When removing the plastic end caps,hold two ends of the plastic cap(as shown in

the following figure) and pull them up about 2mm from the amp.Then they can be

taken away parallelly.

Holding both ends of plastic

cap and remove it parallelly

5) Plastic cap installation completed.

AMPLIFIERS INSTALLATION

2 ) Using attached screws to fix the amplifier to the chosen place.(As shown in figure 1)

3 ) Each plastic end cap has 5 buckles that match 5 buckle holes on the amplifier.

Hold two ends of the plastic end cap and push it towards the amps horizontally.(As

shown in figure 2)

1 ) Choosing a flat and ventilated place to install amplifier.

Be sure to carefully read and understand the instructions before attempting to

install the Amplifier.

1.Installation steps

Horizontal push direction

Figure 1 :

Figure 2 :

Plastic End Caps Fastening Illustration

4) After The Plastic Cap Is Stick To The Amp, Holding Two Ends Of The Plastic

Caps( As Shown In Figure 3 ) And Push them down to the same horizontal level ( As

Shown In The Figure 3).

Holding both ends of the plastic cap,

push down together with same strength.

Figure 3:

6) When removing the plastic end caps,hold two ends of the plastic cap(as shown in

the following figure) and pull them up about 2mm from the amp.Then they can be

taken away parallelly.

Holding both ends of plastic

cap and remove it parallelly

5) Plastic cap installation completed.

AMPLIFIERS INSTALLATION

2 ) Using attached screws to fix the amplifier to the chosen place.(As shown in figure 1)

3 ) Each plastic end cap has 5 buckles that match 5 buckle holes on the amplifier.

Hold two ends of the plastic end cap and push it towards the amps horizontally.(As

shown in figure 2)

1 ) Choosing a flat and ventilated place to install amplifier.

Be sure to carefully read and understand the instructions before attempting to

install the Amplifier.

1.Installation steps

Horizontal push direction

Figure 1 :

Figure 2 :

Plastic End Caps Fastening Illustration

WIRING DIAGRAM

SE90.2/SE150.2 Amplifier wiring

speaker impedance

2~4Ohm

Input 2 Channel Mode

Bridged Mode

Stereo Mode

speaker impedance

2~4Ohm

SUB WOOFER

speaker impedance

4~8Ohm

WIRING DIAGRAM

SE800.1/1500.1/2000.1/3500.1 Amplifier wiring

SUB WOOFER

speaker impedance

1~4Ohm

SUB WOOFER

speaker impedance

2~8Ohm

SUB WOOFER

speaker impedance

2~8Ohm

Single channel input Mode

Two Woofer Load Mode

One Woofer Load Mode

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sound Magus Verstärker Handbücher

Sound Magus

Sound Magus PK600.1M Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung