Sound Storm SCD-550R Bedienungsanleitung

INSTALLATION

Notes:

• Choose the mounting location where the unit will not interfere with the normal

driving function.

• Before final installation, connect the wiring temporarily and make sure the unit and

the system work properly.

• Use only the parts included with the unit to ensure proper installation. The use of

unauthorized parts can cause malfunctions.

• Consult with your nearest dealer if installation requires the drilling of holes or other

modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the

passenger if there is a sudden stop, like an emergency stop.

• If installation angle exceeds 30°from horizontal, the unit might not give its optimum

performance.

• Avoid installing the unit where it would be subject to high temperature, such as from

direct sunlight, from hot air of the heater, or where it would be subject to dust, dirt

or excessive vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either from “Front” (conventional DIN Front-mount)

or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of

the unit chassis). For details, refer to the following illustrated installation methods.

DIN FRONT-MOUNT (Method A)

Installation of the unit

1. Dashboard

2. Mounting Bracket

After inserting the mounting bracket into

the dashboard, select the appropriate

tabs according to the thickness of the

dashboard material and bend them

outward to secure the holder in place.

3. Screw

30˚

182

(Fig. 1)

1. Dashboard

2. Nut (5mm)

3. Spring washer

4. Screw (5 x 25mm)

5. Screw (5 x 28mm)

6. Backstrap

Be sure to use the backstrap to secure

the back of the unit in place. The strap

can be bent by hand to the desired angle.

7. Plain washer

Removing the unit

1. Frame

2. Insert fingers into the groove in the front

of frame and pull out to remove the

frame. (When reattaching the frame,

point the side with groves downward

and attach it.)

3. Lever

Insert the levers supplied with the unit

into the grooves at both sides of the unit

as shown in figure until they click.

Pulling the levers makes it possible to

remove the unit from the dashboard.

DIN REAR-MOUNT (Method B)

Installation using the screw holes on the sides of the unit.

Fastening the unit to the factory radio

mounting bracket.

1. Select a position where the screw holes

of the bracket and the screw holes of

the main unit become aligned (are fitted),

then tighten the screws at 2 places on

each side.

Use either truss screws (5 x 5mm) or

flush surface screws (4 x 5mm),

depending on the shape of the screw

holes in the bracket.

2. Screw

3. Factory radio mounting bracket

4. Dashboard or Console

5. Hook (Remove this part)

Note: The trim piece, backstrap, and

mounting bracket are not used for method

B installation.

(Fig. 2)

USING THE DETACHABLE FRONT PANEL

To Detach the Front Panel

1. Press the release button (REL), the front panel will drop down.

2. Remove the front panel by pulling it outward.

3. For safekeeping, store the front panel in the supplied protective case immediately

after being removed.

4. Push the front metal plate that holds the front panel into the main body. A ‘click’

sound should be heard.

Protective Case

Front Panel

REL

To Reinstall the Front Panel

1. Push the front panel into the main body. A ‘click’ sound should be heard.

2. Note that if the front panel fails to lock in position properly, control buttons may

not function and the display may be missing some segments. Push the release

button and reinstall the front panel again.

Precautions when Handling

1. Do not drop the front panel.

2. Do not put pressure on the display or control buttons when detaching or reinstalling

the front panel.

3. Do not touch the contacts on the front panel or on the main unit body. It may result

in poor electrical contact.

4. If any dirt or foreign substances adhere to the contacts, they can be removed with

a clean and dry cloth.

5. Do not expose the front panel to high temperatures or direct sunlight.

6. Keep away any volatile agents (e.g. benzene, thinner, or insecticides) from touching

the surface of the front panel.

7. Do not attempt to disassemble the front panel.

WIRING CONNECTION

Note:

1. For 2-speakers system, green, violet, white/black and grey/black wire leads are

unconnected and isolated.

2. For 2-speakers system, keep the fader indicator at center position to maintain the

existing volume level.

WHITE

WHITE/BLACK

GREEN

GREEN/BLACK

Lch

SPK.

WHITE

GREEN/BLACK

GREY

GREY/BLACK

VIOLET

VIOLET/BLACK

4-SPEAKERS SYSTEM 4-SPEAKERS SYSTEM

FRONT

Lch SPK.

REAR

Lch SPK.

FRONT

Rch SPK.

REAR

Rch SPK.

2-SPEAKERS SYSTEM 2-SPEAKERS SYSTEM

Rch

SPK.

GREY

VIOLET/BLACK

MAIN UNIT

Rch RED

Lch WHITE

(GREY)

REAR RCA CABLE

Rch RED

Lch WHITE

(BROWN)

FRONT RCA CABLE

ANTENNA CONNECTOR

RED

YELLOW

BLUE

POWER

ANTENNA

GROUND (B–)

MEMORY

BACK-UP

IGNITION

SWITCH (B+) SUBWOOFER

CABLE

(GREEN)

Rch RED

Lch WHITE

(BLACK)

AUX. AUDIO IN

FUSE

BLACK

OPERATION

GENERAL OPERATION

• ON/OFF/ILLUMINATE

Switch on the unit by pressing any button [except EJECT button (4) and REL button

(7)]. When system is on, press ILL/PWR button (9) shortly to control the brightness

of VFD. Hold it for several seconds to turn off the unit.

• FACEPLATE RELEASE

Press REL button (7) to detach the removable faceplate.

• SOUND ADJUSTMENT

Press SEL button (10) to select the desired adjustment mode.

45 2627

22 23212013

18225

10612 16 15

1311 7 17 91924

The adjustment mode will change in the following order.

By pressing VOL button (11) or VOL button (12), it is possible to adjust the

desired level.

• LOUDNESS

Press BND/LOU button (13) for several seconds to reinforce the bass output. The

display will show “LOUD”. Press it for several seconds again to defeat this function.

• SET THE CLOCK

Hold down the DSP button (15) until the clock is shown on the display and flashes.

Then press the TUNE/TRACK button (17) to change hours or TUNE/TRACK

button (16) to change minutes.

• SELECT MODE

Press MOD/SW button (6) to choose desired listening mode.

• SUBWOOFER

Press MOD/SW button (6) for several seconds to toggle subwoofer output.

When subwoofer is on, display will show “SW”. Press it again for several seconds

to release this mode.

• MUTE

Press MUT button (3) to silence the receiver. Press it again to resume listening.

• VACUUM FLUORESCENT DISPLAY

Exhibit current frequency and activated functions on the display (8).

• EQUALIZATION

Press EQ button (19) to turn on equalization function and to select desired audio

mode. There are five modes:

• REMOTE SENSOR

Point the remote control handset to the remote sensor RX (24).

Press the function keys on the handset to control the system.

• FLASHING LED

If the front panel does not install in the unit, the LED (27) will flash.

• RESET

The RESET button (26) must be activated with either a ball point pen or thin pointed

metal object. RESET button (26) is to be activated for the following reasons:

- Initial installation of the unit when all wiring is completed.

- All the function buttons do not operate.

- Error symbol on the display.

Note: If pressing the RESET button (26) doesn’t work, please use a cotton swab

soaked in isopropyl alcohol to clean the socket on the front panel.

Volume Bass Treble Balance Fader

FLAT CLASSICS POP JAZZ DSP OFF

RADIO OPERATION

• BAND SELECTION

For tuner mode, press BND/LOU button (13) briefly to select the desired band.

The reception band will change in the following order:

• STATION SELECTION

Press TUNE/TRACK button (17) or TUNE/TRACK button (16) briefly to activate

automatic seek function. Press for several seconds until “MANUAL” appears on

the display. The manual tuning mode is now active. If both buttons have not been

pressed for several seconds, they will return to “seek tuning” mode and “AUTO”

will appear on the display.

• LOCAL/DISTANCE

Press LOC button (1) briefly to select between local and distant stations.

“Local” setting is for reception of strong stations, and “distant” setting is for

reception of weaker stations. This function is in during AUTO SEEK operation.

• AUTOMATIC MEMORY STORING & PROGRAM SCANNING

- Automatic Memory Storing

Press AMS button (18) for several seconds. The radio searches from the current

frequency and checks the signal strength until one cycle search is finished.

The 6 strongest stations are stored into the location corresponding to the preset

buttons.

- Program Scanning

Press AMS button (18) briefly to scan preset stations. When the field strength

level is more than the tuners threshold sensitivity level, the tuner will hold at that

preset number for several seconds with muting released, then searches again.

• STATION STORING

Select a station. Then press any one of the preset buttons (14) (M1 to M6) to store

a station into memory. Press this button for several seconds, the station is then

stored into the number button.

• MONO/STEREO

Press MONO button (25) to select mono or stereo mode. You can sometimes

improve reception of distant stations by selecting mono operation.

• SCAN

Press SCAN button (2) to set the function to scan mode. The tuner will stop at

each station with a receivable signal and will stay tuned for several seconds, long

enough to decide whether to stop at that station or to let the tuner continue to scan.

FM1 FM2 FM3 AM

CD OPERATION

• SELECT TRACKS

During CD operation, press TUNE/TRACK button (16) or TUNE/TRACK button

(17) to move to the previous track or the following track. Track number shows on

the display.

During CD operation, hold TUNE/TRACK button (16) or TUNE/TRACK button

(17) to fast reverse or fast forward. CD play starts from when you release the

button.

• PAUSE PLAYING

Press PAU button (20) to pause CD player. Press it again to resume play.

• REPEAT THE SAME TRACK

During CD operation, press RPT button (22) to continuously repeat the same track.

Press again to stop repeat.

• PREVIEW ALL TRACKS

During CD operation, press SCN button (21) to play first several seconds of each

track on the current disc. Press again to stop intro and listen to track.

• PLAY ALL TRACKS

During CD operation, press SHF button (23) to play all tracks on CD in random

order. Press again to cancel the function.

• EJECT

Press EJECT button (4) to stop CD play and eject the disc from the slot (5).

NOTE ON CD-R/CD-RW DISCS

• On this unit, in addition to an audio CD, you can play your original CD-R or CD-RW

discs that contain audio titles.

• However, depending on the condition of the recording equipment or the CD-R or

CD-RW itself, some CD-Rs or CD-RWs may not play in this unit.

• DO NOT stick paper or tape, etc, onto label side or the recorded side of any

CD-R/CD-RW, as it may cause a malfunction.

Inhaltsverzeichnis

Andere Sound Storm Autoempfänger Handbücher

Sound Storm

Sound Storm SD712B Bedienungsanleitung

Sound Storm

Sound Storm ML33USA Bedienungsanleitung

Sound Storm

Sound Storm SDVD550T Bedienungsanleitung

Sound Storm

Sound Storm SCD-150 Bedienungsanleitung

Sound Storm

Sound Storm STM93RDS Bedienungsanleitung

Sound Storm

Sound Storm RDSM43UA Bedienungsanleitung

Sound Storm

Sound Storm SD315 Bedienungsanleitung

Sound Storm

Sound Storm SD706MI Bedienungsanleitung

Sound Storm

Sound Storm M330USA Bedienungsanleitung

Sound Storm

Sound Storm RDSM35A Bedienungsanleitung

Sound Storm

Sound Storm SDVD100 Bedienungsanleitung

Sound Storm

Sound Storm SD735 Bedienungsanleitung

Sound Storm

Sound Storm M312USA Bedienungsanleitung

Sound Storm

Sound Storm SDC25A Bedienungsanleitung

Sound Storm

Sound Storm SDVD-600 Bedienungsanleitung

Sound Storm

Sound Storm ML40USA Bedienungsanleitung

Sound Storm

Sound Storm SD877BI Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Sound Storm

Sound Storm SCD-350 Bedienungsanleitung

Sound Storm

Sound Storm S638BTA Bedienungsanleitung

Sound Storm

Sound Storm SD710 Bedienungsanleitung

Sound Storm

Sound Storm SD730M Bedienungsanleitung

Sound Storm

Sound Storm SDC22A Bedienungsanleitung

Sound Storm

Sound Storm SD320 Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung