SoundCraft 328xd Bedienungsanleitung

RIGHT

STE-2STE-1

SELECT

MUTE

SOLO

MIX

dBFS

0dBFS = 18dBu

STEREO INPUTS

GROUP LINK

CHANNEL /

XDX D

EXIT

PARAMETER

FUNCTION

OUT

THRU

MIDI

IN OUT IN

OUT

S/PDIF

OUT IN

AES/EBU

WORD

CLOCK CLOCK

WORD/SUPER

WAVECENTER/PCI

FRONTIER DESIGN

328

Soundcraft 328XD and Frontier Design WaveCenter/PCI

328XD AND

328XD AND328XD AND

328XD AND

FRONTIER DESIGN

FRONTIER DESIGNFRONTIER DESIGN

FRONTIER DESIGN

WAVECENTER/PCI

WAVECENTER/PCIWAVECENTER/PCI

WAVECENTER/PCI

Connecting the system 2

328XD Configuration 3

WaveCenter/PCI Configuration 6

Using the WaveCenter/PCI with the 328XD 12

Soundcraft 328XD and Frontier Design WaveCeneter/PCI

CONNECTING THE SYSTEM

Audio Connections

Audio connections should be made as shown in the diagram below. ADAT optical cables must be

connected from the ADAT Out port of the WaveCenter/PCI card to the ADAT In port of the 328XD, and vice

versa. 75

Ω

Coaxial digital S/PDIF cables must also be connected from the WaveCenter/PCI S/PDIF output

to the 328XD S/PDIF input and vice versa.

In this configuration, the ADAT connections allow digital transfer of either direct outputs from the 328XD’s

input channels 1-8 to the WaveCenter/PCI card, or the 328XD’s 8 Group outputs. The S/PDIF output

from the console can be assigned to either the Mix output, 1 of 3 stereo auxiliary outputs (Aux 1/2, Aux

3/4 or FX-1/2), pairs of Group outputs or the Control Room output. The 328XD S/PDIF Input can be

configured as a digital Stereo Input or as a digital 2-Track Return.

Other Connections

You may also wish to connect the 328XD to the WaveCenter/PCI card via MIDI to allow MIDI automation /

System Exclusive dumps from the 328XD to be recorded and played back from your PC.

If you wish to connect the 328XD to the WaveCenter/PCI card via MIDI, the following connections must be

made:

Soundcraft 328XD and Frontier Design WaveCenter/PCI

328XD CONFIGURATION

Wordclock

The WaveCenter/PCI card and the 328XD (plus any other devices in the studio setup) must have their

internal clocks synchronized to allow correct transmission and reception of digital information throughout

the system. This is achieved by configuring one of the devices as a wordclock master, and configuring all

other devices in the studio setup to slave to this wordclock, synchronizing all clocks in the studio setup.

In this case, the 328XD will be set to wordclock master, and the WaveCenter/PCI will be set to slave to

the 328XD, via the WaveCenter/PCI’s S/PDIF input. Any other devices interfacing digitally with the 328XD

within the studio setup will also be configured to slave to the 328XD’s wordclock.

NOTE:

Wordclock information is embedded into the S/PDIF data stream output by the 328XD,

enabling the WaveCenter/PCI to slave to the 328XD’s S/PDIF output.

To configure the 328XD as the wordclock master, enter the 328XD’s Main Menu page by pressing the

<MENU> button to the right hand side of the LCD display. Using the PARAM encoder beneath the

display, scroll up or down until the ‘Clock Source Sel’ menu is highlighted, and press <ENTER>. Here,

either ‘Internal: 44.1kHz’ or ‘Internal: 48kHz’ clock must be selected for the 328XD to function as

wordclock master. Set this to the samplerate you wish to work at then press <ENTER> to confirm the

samplerate setting. Press <MENU> to return to the Menu pages.

Tape Ports

To ensure that the 328XD Tape Ports are configured to ‘ADAT’ to work with the WaveCenter/PCI, enter

the 328XD Menu pages by pressing the <MENU> button to the right hand side of the LCD display.

Using the PARAM encoder beneath the display, scroll up or down until the ‘Tape Port Select’ menu is

highlighted and press <ENTER>.

Now press the Up cursor key until the ‘<Tape Ch17-24 >’ menu page is displayed. Using the PARAM

encoder set the ‘Bank Source’ to ‘ADAT’:

Soundcraft 328XD and Frontier Design WaveCeneter/PCI

Now press the Down cursor key to set the wordlength. The WaveCenter/PCI is capable of 24 bit recording,

and so for optimum results, 24 bit wordlength can be selected here. If your sequencer supports 16 or 20

bit resolution, set appropriately. Check your sequencer manual for more information.

S/PDIF Input

The 328XD S/PDIF input can be routed to any one of the following inputs:

Stereo Input 1, Stereo Input 2, FX-1, FX-2, 2-Track Tape Return

provided that the AES/EBU input or oscillator has not already been assigned to that input.

Commonly the WaveCenter/PCI S/PDIF output would be routed to Stereo Input 2, or the 2-Track Tape

Return input.

NOTE:

Assigning a digital source to an input will override any analogue signal present on that input.

Press <MENU> to enter the menu pages, scroll through the pages until the ‘SPDIF I/P Setup’ is

highlighted and press <ENTER>. Using the PARAM encoder, select the destination for the S/PDIF input,

and press <ENTER> to confirm the setting:

NOTE:

If the S/PDIF input is not required, NOWHERE should be selected in the menu.

S/PDIF Output

The stereo 328XD S/PDIF output can be sourced from any of the following busses:

Mix L/R, Aux 1/2, Aux 3/4, FX-1/2, Groups 1-8 in odd / even pairs or Control Room output

This will usually be set to ‘Mix’, to allow a stereo mixdown to be recorded directly into the WaveCenter/PCI

on the playback of a mix.

As the WaveCenter/PCI is a full duplex device, it is possible to playback a composition consisting of all 8

ADAT tracks + 1 Stereo S/PDIF track from the WaveCenter/PCI, recording the mixed signal from the

328XD back into the WaveCenter/PCI’s S/PDIF input as a stereo mixdown.

Press <MENU> to enter the menu pages, scroll through the pages until the ‘SPDIF O/P Setup’ is

highlighted and press <ENTER>. Using the PARAM encoder, select the source for the S/PDIF output

Soundcraft 328XD and Frontier Design WaveCenter/PCI

NOTE:

If the S/PDIF output is not required, NOWHERE should be selected in the menu. In this case,

wordclock will still be transmitted through the S/PDIF output of the 328XD, even though no

audio signal is transmitted.

The wordlength of the S/PDIF output must now be set. Press the down cursor to access the S/PDIF

output wordlength setting. Here, the desired wordlength can be set to 16, 20 or 24 bit.

NOTE:

If using the WaveCenter/PCI as an ASIO device, it is important here that the wordlength set

here is the same as the 328XD Tape Port wordlength (See ‘Tape Ports’)

Soundcraft 328XD and Frontier Design WaveCeneter/PCI

WAVECENTER/PCI CONFIGURATION

Wordclock and S/PDIF Input

The WaveCenter/PCI must be set up to receive the wordclock transmitted by the 328XD (via the 328XD’s

S/PDIF output).

Open the WaveCenter/PCI Control Panel, accessed by double clicking the WaveCenter/PCI icon on the

Windows taskbar:

Click on the ‘Clock/Device Status’ tab. The following window should open:

NOTE:

Alternatively, the WaveCenter/PCI will also successfully clock to the ADAT output of the 328XD.

The WaveCenter/PCI could also be set as wordclock master, and the 328XD can slave to the

WaveCenter/PCI via the S/PDIF connections. However, the recommended configuration is to set

the 328XD as wordclock master, with the WaveCenter/PCI slaving via S/PDIF, as outlined in this

manual.

Now the sample rate must be set. In the ‘Sample Rate’ section, select the sample rate at which you wish

to work. This should match the sample rate of the internal clock on the 328XD:

Soundcraft 328XD and Frontier Design WaveCenter/PCI

NOTE:

You can force Windows applications to only play back at the chosen sample rate by ticking

the ‘Lock’ tick box in the ‘Sample Rate’ section.

On the WaveCenter/PCI, the stereo device ‘S 1:2’ (S/PDIF format) can be sourced from any physical

input. In this configuration, it must be set to source from the WaveCenter/PCI coaxial S/PDIF input. With

the ‘S 1:2’ input set to ‘Coax’, the WaveCenter/PCI recevies the S/PDIF stream from the 328XD, enabling

the WaveCenter/PCI to slave to the 328XD via S/PDIF, and also allows the 328XD to send S/PDIF stereo

data back to the WaveCenter/PCI.

To make this setting, select ‘Coax’ from the ‘S 1:2’ pull-down menu.

Soundcraft 328XD and Frontier Design WaveCeneter/PCI

Now the validity of the S/PDIF input received by the WaveCenter/PCI must be checked. The ‘Digital Input

Status’ section of the ‘Clock/Device Status’ WaveCenter/PCI Control Panel shows the validity of the S/PDIF

input with the following 3 indicators.

S/PDIF input status indicators (From left to right): Signal Active/Inactive, Digital Audio Format Valid/Invalid,

WaveCenter/PCI Locked/Unlocked

Firstly, click on ‘Clear Errors’ to initialize the indicators.

In this configuration, all indicators should be continuously showing green. If any of the indicators are red,

or display a slash, the S/PDIF output by the 328XD is not correctly being interpreted by the

WaveCenter/PCI. If this is the case, check the S/PDIF cable is correctly connected from the S/PDIF output

of the 328XD to the S/PDIF input of the WaveCenter/PCI. If the indicators are still showing errors, check

also that all the correct 328XD and WaveCenter/PCI settings have been made, as described so far in this

manual

NOTE:

A 75

Ω

coaxial S/PDIF cable must be used to correctly transfer the S/PDIF digital data from the

328XD to the WaveCenter/PCI. A standard phono cable will not guarantee satisfactory data

transfer.

If all three indicators are continually green, the WaveCenter/PCI is correctly slaving to the 328XD’s

wordclock, and the S/PDIF data format is being correctly interpreted by the WaveCenter/PCI.

Soundcraft 328XD and Frontier Design WaveCenter/PCI

S/PDIF Output

The stereo output from the WaveCenter/PCI can be set to either AES/EBU or S/PDIF format. In this

configuration, this should be set to S/PDIF, so that the 328XD correctly interprets the stereo data

incoming to the 328XD’s S/PDIF input.

In the WaveCenter/PCI Control Panel, select the ‘System’ tab. In the ‘Output Channel Status’ section,

select ‘Consumer (S/PDIF)’:

Andere Handbücher für 328xd

Inhaltsverzeichnis

Andere SoundCraft Musikmixer Handbücher

SoundCraft

SoundCraft Vi4 Bedienungsanleitung

SoundCraft

SoundCraft UREI 1601E Bedienungsanleitung

SoundCraft

SoundCraft Spirit FX16 Bedienungsanleitung

SoundCraft

SoundCraft S6000 Bedienungsanleitung

SoundCraft

SoundCraft SPIRIT LIVE 4 2 Bedienungsanleitung

SoundCraft

SoundCraft GB8 Bedienungsanleitung

SoundCraft

SoundCraft MH3 Bedienungsanleitung

SoundCraft

SoundCraft MBI 10 Series Bedienungsanleitung

SoundCraft

SoundCraft 400B Series Bedienungsanleitung

SoundCraft

SoundCraft Si Impact Bedienungsanleitung

SoundCraft

SoundCraft Si3 Bedienungsanleitung

SoundCraft

SoundCraft 328xd Bedienungsanleitung

SoundCraft

SoundCraft Delta Theatre Bedienungsanleitung

SoundCraft

SoundCraft Spirit Folio Lite Bedienungsanleitung

SoundCraft

SoundCraft BVE100 Bedienungsanleitung

SoundCraft

SoundCraft FX16II Bedienungsanleitung

SoundCraft

SoundCraft K3 Bedienungsanleitung

SoundCraft

SoundCraft Si Series Bedienungsanleitung

SoundCraft

SoundCraft MPMI Bedienungsanleitung

SoundCraft

SoundCraft MH2 Bedienungsanleitung

SoundCraft

SoundCraft LX7II Bedienungsanleitung

SoundCraft

SoundCraft Si Compact Bedienungsanleitung

SoundCraft

SoundCraft SPIRIT PRO TRACKER Bedienungsanleitung

SoundCraft

SoundCraft 200 Delta Bedienungsanleitung

Beliebte Musikmixer Handbücher anderer Marken

Neve

Neve 8816 Bedienungsanleitung

Mackie

Mackie Onyx Analogue Mixer Bedienungsanleitung

Behringer

Behringer EUROPOWER PMP518M Bedienungsanleitung

Peavey

Peavey S-32 Sanctuary Series Bedienungsanleitung

Rane

Rane MP 4 Bedienungsanleitung

True

True T9 Touchscreen Console Bedienungsanleitung

Studiomaster

Studiomaster Air Pro 24 Bedienungsanleitung

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Bedienungsanleitung

Roland

Roland M-160 Bedienungsanleitung

Yamaha

Yamaha MR1642 Bedienungsanleitung

Ecler

Ecler MAC40v Bedienungsanleitung

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Bedienungsanleitung

Veeder-Root

Veeder-Root TLS-350 Series Bedienungsanleitung

Alto

Alto APM80.QUAD Bedienungsanleitung

Omnitronic

Omnitronic PM-211 Bedienungsanleitung

Roland

Roland SoundCanvas SC-8820 Bedienungsanleitung

CARVIN

CARVIN RX 1200 Bedienungsanleitung

Roland

Roland M-16E Bedienungsanleitung