SoundCraft MADI-USB Combo Card Bedienungsanleitung

User Guide

by HARMAN

MADI-USB Combo Card

Soundcraft MADI-USB Card User Guide 0914

Part No. 5049248

Soundcraft is a trading division of Harman International Industries Ltd. Information in this manual is subject to

change without notice and does not represent a commitment on the part of the vendor. Soundcraft shall not be

liable for any loss or damage whatsoever arising from the use of information or any error contained in this manual.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any

means, electronic, electrical, mechanical, optical, chemical, including photocopying and recording, for any

purpose without the express written permission of Soundcraft.

Harman International Industries Limited

Cranborne House, Cranborne Road, POTTERS BAR, Hertfordshire, EN6 3JN, UK

Tel:+44 (0)1707 665000

Fax:+44 (0)1707 660742

http://www.soundcraft.com

IMPORTANT

Please read this manual carefully before using

your card for the rst time.

Warning: Any modication or changes made to this device, unless explicitly approved by Harman, will

invalidate the authorisation of this device. Operation of an unauthorised device is prohibited under

Section 302 of the Communications act of 1934, as amended, and Subpart 1 of Part 2 of Chapter 47

of the Code of Federal Regulations.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

* Reorient or relocate the receiving antenna

* Increase the separation between the equipment and the receiver

* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

* Consult the dealer or an experienced radio/TV technician for help

For further details contact

Harman International Industries Ltd, Cranborne House, Cranborne Road, Potters Bar, Hertfordshire EN6 3JN, UK

Telephone +44(0) 1707 665000 Fax +44 (0)1707 660742 email: [email protected]

[email protected]

This equipment complies

with the EMC Directive

2004/108/EC and LVD

2006/95/EC

This equipment complies with the EMC directive 2004/108/EC

This product is approved to

EMC standards

EN55103-1: 2009 (E2)

EN55103-2: 2009 (E2)

by HARMAN

Soundcraft MADI-USB Card User Guide 0914

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including ampliers) that produce heat.

Do not defeat the safety purpose of a polarised or grounding type plug. A polarised plug

has two blades with one wider than the other. A grounding type plug has two blades and

a third grounding prong. The wide blade or the third prong are provided for your safety. If

the provided plug does not t into your outlet, consult an electrician for replacement of

the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles and the point where they exit from the apparatus.

Only use attachments/accessories specied by the manufacturer.

Use only with the cart, stand, tripod, bracket or table specied by the manufacturer, or sold

with the apparatus. When a cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualied service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has

been spilled or objects fallen into the apparatus, the apparatus has been exposed to rain

or moisture, does not operate normally, or has been dropped.

NOTE: It is recommended that all maintenance and service on the product should be carried

out by Soundcraft or its authorised agents.Soundcraft cannot accept any liability whatsoever

for any loss or damage caused by service, maintenance or repair by unauthorised personnel.

WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to

rain or moisture. Do not expose the apparatus to dripping or splashing and do not place

objects lled with liquids, such as vases, on the apparatus. No naked ame sources, such

as lighted candles, should be placed on the apparatus.

Ventilation should not be impeded by covering the ventilation openings with items such as

newspapers, table cloths, curtains etc.

Soundcraft MADI-USB Card User Guide 0914

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to cor-

rect the interference at his own expense.

This Class B digital apparatus meets the requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de la ClasseB respecte toutes les exigences du Règlement sur le

matériel brouilleur du Canada.

Soundcraft MADI-USB Card User Guide 0914

FOR YOUR OWN SAFETY AND TO AVOID INVALIDATION OF THE WARRANTY

PLEASE READ THIS SECTION CAREFULLY.

SAFETY SYMBOL GUIDE

For your own safety and to avoid invalidation of the warranty all text marked with

these symbols should be read carefully.

WARNINGS

The lightning ash with arrowhead symbol, is intended to alert the

user to the presence of un-insulated “dangerous voltage” within the

product’s enclosure that may be of sufcient magnitude to constitute

a risk of electric shock to persons.

CAUTIONS

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying

the appliance.

NOTES

Contain important information and useful tips on the operation of

your equipment.

HEADPHONES SAFETY WARNING

Contain important information and useful tips on headphone

outputs and monitoring levels.

Soundcraft MADI-USB Card User Guide 0914

INTRODUCTION

The Soundcraft® MADI-USB Combo card offers digital audio connection between an Si series

console*1 and Apple® Mac® or PC with a USB port as well as any of the Soundcraft range

of Stageboxes via Soundcraft’s proprietary Cat 5 MADI connection.

Audio capability across the USB link is 32 channels in and 32 channels out at 48KHz, whilst

the Cat 5 MADI port can be used simultaneously with up to 32 inputs and 32 outputs. More

channels can be transported via MADI at the expense of the USB connection for a maximum

of 64 MADI input/output paths.

Connection and setup of the card to a PC is made simple with the use of the Soundcraft

digital audio driver and associated control panel. USB connection to a Mac requires no extra

software or drivers.

The MADI-USB Combo card is an ideal platform from which to record and use a Stagebox

at live situations where recording and remote I/O is a must.

NOTE: Only a maximum of 32 channels of the USB can be used. Standard conguration

allows for 32x32 channels of USB and 32x32 channels of remote I/O simultaneously.

NOTE: The packaging, in which your card arrived, forms part of the product and must be

retained for future use.

Soundcraft MADI-USB Card User Guide 0914

INSTALLING THE DRIVERS (PC ONLY)

To use the MADI-USB Combo

Card on PCs additional drivers

are necessary. Soundcraft’s

MADI-USB Combo card

audio drivers can be found

on the Soundcraft website

(www.soundcraft.com). The

install package includes

WDM and ASIO drivers for

low-latency operation with

a control panel to congure

driver settings for best performance.

Before you install the PC drivers, insert the MADI-USB Combo Card into the console, connect

the PC to the MADI-USB Combo card and boot the console.

Once the drivers are installed, shortcuts for the control panel are available on the desktop

or under all programs, Harman Pro, Soundcraft, Multichannel USB Audio.

When the card is connected to the computer, taskbar icons will indicate a device has been

detected and clicking the icon will open the appropriate control panel.

When the drivers are installed onto your PC, you will need to restart your machine for the

install process to be complete.

NOTE: Additional drivers are not needed for Mac as the MADI-USB Combo card uses

Apple®’s Core Audio drivers for USB recording.

CONFIGURING THE AUDIO SETTINGS

The Soundcraft Audio Driver

settings can be found in

the Soundcraft USB Control

Panel. Within this menu,

there are options to adjust

the streaming mode of the

MADI-USB Combo Card

and the buffer size from

64 samples up to 8192

samples.

Recommended buffer size will vary depending on application, however higher buffer sizes

should be used when monitoring from the DAW is not necessary. For most live recording

applications, a standard buffer size of 1024 samples is enough to ensure reliable operation

and clean audio.

The streaming mode settings modify the behaviour of the USB driver for maximum

optimisation when set in conjunction with the buffer size setting. The buffer size modies

the amount of audio data that is stored before being released into the application.A large

buffer size results in higher latency to your DAW. A small buffer size reduces the latency to

your DAW but can cause audio glitches and errors.

1394 control panel, similar for USB

Soundcraft MADI-USB Card User Guide 0914

To adjust the buffer size of the MADI-USB Combo card, both the streaming mode and the

buffer size settings need to be set correctly corresponding to one another.

For example, by setting the streaming mode to ‘Reliable’ and then the buffer size to 1024

samples, the system will then be running at 1024 samples and the audio will be clean.

For lower buffer sizes, the streaming mode should be set to ‘Low Latency’ and the buffer

size to 128 samples.

A mismatch between Streaming mode and buffer size could cause artefacts in the audio

and could corrupt the audio recording. A mismatched buffer setting such as setting the

streaming mode to ‘Reliable’ and the buffer size to 64 samples would result in distorted

audio in your recording.

To avoid artefacts and to produce a reliable recording you should select the appropriate

buffer size for the streaming mode. When a mismatch occurs, a dialogue will appear at

the bottom of the control panel menu with instructions of where to go from the current

setting to make a compatible setup.

NOTE: The ability to set low buffer sizes depends mostly on CPU Performance. A

high-performance computer with a dedicated USB bus will be able to achieve small

buffer sizes.

Soundcraft MADI-USB Card User Guide 0914

FINDING THE CORRECT CABLE

The USB port on the MADI-USB combo card

is the ‘B type’ connector (the standard type

for peripheral devices). USB host devices

use the rectangular ‘A type’ connector. As

such, a ‘Type A to type B’ USB cable is

required.

NOTE: USB cables come in many forms.

Please ensure you use the correct cables

for your system for optimal performance.

DIP SWITCH CONFIGURATIONS

Dip switches on the card provide extra exibility depending on the application. The card is

sent out of the factory in a standard conguration that allows for 32 channels of Stagebox

connectivity and 32 channels of USB recording located on channels 1-32 and 33-64

respectively.

If an application requires a different setup than standard then there are a few more

options. There is a ledger on the PCB that displays the options that are achievable. This

can be seen below:

The standard conguration

Switch 1 alters the syncing interaction between the

MADI-USB Combo card and the mixer. As standard,

the card should be set to sync to the mixer and so,

switch 1 should be set OFF.

To connect two consoles together using two

MADI-USB Combo cards, for a master/slave type

operation, the card within the master console should

be set to sync to the Mixer (switch 1 OFF), and the

slave console/card set to sync to the Card (Switch

1 ON). The consoles will then need to be set to

INTernal and OPTion clocking respectively.

Switch 2 determines what channel the USB is sent

out from on the USB portion of the option card. USB

OUT corresponds to output paths on the console

that are patched to USB. This switch should be set to correspond with the input range of

the USB. As standard, this switch should be set to ON (33-64).

USB Type A to B

SW1,4 and SW1,3 is short for switches 3

and 4 respectively on the rst dipswitch on

the option card.

This is the standard conguration which

allows for 32 channels of Stagebox

connectivity and 32 channels of

simultaneous USB recording.

Soundcraft MADI-USB Card User Guide 0914

Switch 3 and 4 together determine the input range and positions of the MADI and USB

streams on the 64 channel total. Using these switches and the graph provided on the

card itself, the MADI and USB streams can be moved to either ranges 1-32 or 33-64.

Asstandard, switch 3 should be set OFF and switch 4 should be set to ON.

Alternative setups: (MADI 64x32, USB 0x32)

By using the graph,it is also possible to achieve 64 channels of Stagebox input connectivity

via MADI at the expense of the USB Input channels. It is possible to receive 64 channels

of MADI while also sending 32 channels of USB outputs, allowing for 32 channel USB

recording while simultaneously using a Soundcraft Stagebox up to a 64x32 conguration.

To achieve this, switches 3 and 4 should be set to OFF and switch 2 should be set to ON

or OFF depending on where the USB channels should be occupied (1-32 or 33-64).

As standard USB outputs should be set to inputs 33-64 (Switch 2 set to ON)

The standard conguration is a setup that allows for the most common of use cases and,

for the most part, the card is a plug-and-play type operation.

If more than 32 channels are required for Stagebox connectivity, then all 64 channels can

be connected to a Stagebox at the expense of the USB channels. For this setup switches3

and 4 must be turned OFF.

Inhaltsverzeichnis

Andere SoundCraft Soundkarte Handbücher

SoundCraft

SoundCraft Si Multi Digital Bedienungsanleitung

Beliebte Soundkarte Handbücher anderer Marken

PCchips

PCchips CMI8330 Bedienungsanleitung

Creative

Creative Sound BlasterX G5 SB1700 Bedienungsanleitung

IBM

IBM Music Feature Card Bedienungsanleitung

Diamond Multimedia

Diamond Multimedia Xtreme Sound Bedienungsanleitung

Digigram

Digigram VX222v2 Bedienungsanleitung

Pure Speed

Pure Speed DSU6000 Bedienungsanleitung

Philips

Philips Seismic Edge PSC704 Bedienungsanleitung

ADDAC System

ADDAC System ADDAC604 Bedienungsanleitung

Asus

Asus Audio Card Xonar D2 Bedienungsanleitung

Soundwave

Soundwave 7.1 Bedienungsanleitung

Creative

Creative Sound Blaster Pro Bedienungsanleitung

Digigram

Digigram VX222-Mic Bedienungsanleitung

HRT

HRT LineStreamer+ Bedienungsanleitung

ST AEKD-STEREOAVAS Bedienungsanleitung

AuviTran

AuviTran AVY16-ES100 Bedienungsanleitung

Creative

Creative Sound BLASTER Audige Rx SB1550 Bedienungsanleitung

IQaudIO

IQaudIO PI-DAC+ Bedienungsanleitung

VideoLogic

VideoLogic SonicVortex2 Bedienungsanleitung