Soundstream XXX-15000D Bedienungsanleitung

Inhaltsverzeichnis

Andere Soundstream Verstärker Handbücher

Soundstream

Soundstream DIGI-Q Bedienungsanleitung

Soundstream

Soundstream Reference 500sx Programmierhandbuch

Soundstream

Soundstream ST4.1000DB Bedienungsanleitung

Soundstream

Soundstream TRX10000 Bedienungsanleitung

Soundstream

Soundstream RUBICON 1002 Programmierhandbuch

Soundstream

Soundstream Reference Series 200 Programmierhandbuch

Soundstream

Soundstream LW1.350 Programmierhandbuch

Soundstream

Soundstream LIL'WONDER LW1.1100D Programmierhandbuch

Soundstream

Soundstream Picasso P1.210 Bedienungsanleitung

Soundstream

Soundstream P203 Programmierhandbuch

Soundstream

Soundstream Di175.1 Bedienungsanleitung

Soundstream

Soundstream RUBICON 1002 Programmierhandbuch

Soundstream

Soundstream Reference Series CLASS-A-3.0 Bedienungsanleitung

Soundstream

Soundstream Tarantula TA2.160 Bedienungsanleitung

Soundstream

Soundstream Tarantula Amplifier Series Programmierhandbuch

Soundstream

Soundstream REF300.2 Bedienungsanleitung

Soundstream

Soundstream Tarantula Amplifier Series Bedienungsanleitung

Soundstream

Soundstream REFERENCE 404s Programmierhandbuch

Soundstream

Soundstream LIL WONDER LW1.400 Bedienungsanleitung

Soundstream

Soundstream TARANTULA NANO Bedienungsanleitung

Soundstream

Soundstream AirBass Bedienungsanleitung

Soundstream

Soundstream HRU. 2 Bedienungsanleitung

Soundstream

Soundstream RUBICON RUBICON Class A 5.2 102 Programmierhandbuch

Soundstream

Soundstream Rubicon RUB600-4 Programmierhandbuch

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung

3 - 4

5 - 9

10

11

12

Class D Topology IR2110S

S/N 87dB at 15kW @ 1 ohm

All "N" Channel MOSFET TO218 Transistors

Unregulated Power Supply

140 Volt Rails +/- for INSANE Amounts of Power

Capacitance Voltage 160V

Monster Solid Copper Buss Bars to Pass >1000 Amps of Current

Idle Current Draw 8 amps

Maximum Current Draw >1400 amps

Dual Monoblock Internally Bridged

Digitally Controlled Module for Damping Factor >1000 @ 100Hz

200mV - 7.6V Input Sensitivity

Short Circuit Speaker Protection

Thermal Protection

Optimized for a 16 Volt DC Power Supply

Totally Separated PWM Circuit to Eliminate Noise

SPECIFICATIONS

4

Unique Protection Sensing Circuit for Maximum Power

2.5mm Thick PCB (57% thicker than normal 1.6mm)

Over 83 Pounds!

Comes with Plexiglass & Metal Bottoms

Remote Bass Control Included

12 5/8" W x 2 3/4" T x 32 11/16" L

Subsonic Filter 15-50Hz @ 24dB Per Octave

Low-Pass X-over 40-275Hz @ 24dB Per Octave

Bass Boost 40-120Hz, 0-18dB

(4) 1/0 Gauge Power Input Terminals

(4) 1/0 Gauge Ground Input Terminals

(2) 8 Gauge Remote Turn-On Terminals

(4) 8 Gauge Speaker Output Terminals

Power at 16 Volts

L oad T HD 1% T HD 5% T HD 10%

1 ohm ea ch ch 4.55 kW 5.125 kW 6 kW

5 ohm ea ch ch 7. 34 kW 8. 2 kW 9.31 kW

2 ohm Bridged 8. 88 kW 10.4 kW 12.2 kW

1 ohm Bridged 14.4 kW 16.4 kW 19 kW

P ower at 14.4 Volts

L oad T HD 1% T HD 5% T HD 10%

1 ohm ea ch ch 4. 1 kW 4.616 kW 5. 4 kW

5 ohm ea ch ch 6.63 kW 7.4 kW 8.379 kW

2 ohm Bridged 8 kW 9. 36 kW 11 kW

1 ohm Bridged 13 kW 14.8 kW 17.1 kW

The XXX-15000D performs best with a 16 volt power source.

Soundstream recommends using a minimum 14.4 power source.

SPEAKER OUTPUT SPEAKER OUTPUT

LINPUT RGAIN

MIN MAX

SUBSONIC BASS EQ

10Hz 50Hz

REMOTE

40Hz 120Hz

LPF POWER

[GREEN]

PROTECT

[RED]

35Hz 250Hz

BASS

BOOST

0dB 18dB

BRIDGED + +

+ +

POWER INPUT

GND GND +12V +12V +12V +12V GND GND

REM

5

LINPUT R

2.Gain

1.Input RCA jacks

10 50

3.Subsonic

GAIN

These inputs are for signal cables from the source. Always use high quality RCA cables.

This control allows you to vary the amplifiers input sensitivity between 0.2[200millivolts]and 7.6volts.

Clockwise rotation raises the threshold and lowers the sensitivity, requiring higher input signal voltage

from the source. in order to obtain maximum output. counter-clockwise adjustment lowers the threshold

and raises the sensitivity, requiring a lower source voltage from source unit. The overall objective is to set

this control to closely match the voltage produced by the source unit.

Avoid setting the theshold too low and supplying excessive input signal voltage, as this would saturate

the input stages and introduce unwanted distortion.

Variable Subsonic Filter[10Hz - 50Hz]

The Subsonic filter will roll off all the unwanted frequencies below 10Hz - 50Hz.

This will allow the amplifier to use that wasted power in the audible bandwidth.

6

LPF

35Hz 250Hz

5.LPF Control

6.Remote Control input

The Bass EQ control is used to select the boost frequency. Any frequency from 40 to 120 Hz can be

selected. The Bass Boost control will increase the frequency selected from the Bass EQ up to 18dB.

This control is used to set desired low pass frequency[35 ~ 250Hz]

The filter acts to cut-off frequencies above the set-point.

The Remote input can be connected to the Remote Dash Control with the supplied connection cable.

This control can be used to adjust the amplifier's input sensitivity.

4.Bass Boost & EQ Control

40Hz 120Hz

7

POWER

[GREEN]

PROTECT

[RED]

GND GND

8.Gnd[Chassis ground)

7. LED indicatior

8

POWER : This GREEN LED will illuminate when the amplifier is turned“ON”. If it fails to illuminate check

the power connections to the amplifier and fuses.

PROTECT : The amplifier protection circuitry will disable the amplifier if input overload, short circuit or

extremely high temperature conditions are detected. when the protection mode is in operation

the red LED indicator on the side panel will be illuminated the amplifier has gone into a self-preservation

mode.

If you observe that the protection LED is lit, please check the system carefully to determine what has

caused the protection circuit to engage. the amplifier can be reset by turning the remote power off

and then on again. If the amplifier shut down due to a thermal overload condition. please allow it to

cool down before restarting. If the amplifier shut down of an input overload or short circuit .be sure

to repair these conditions before attempting to power up the amplifier again.

To avoid unwanted ignition noise caused by ground loops. It is essential that the amplifier be grounded

to a clean, bare, metal surface of the vehicles chassis.

It is not recommended to use seat or seat belt bolts..

+12V +12V

9.Power[Battery positive]

10.

REM

9

Due to the power requirements of the amplifier this connection should be made directly to the positive

[+] terminal of battery. For safety measure install an in-line fuse Holder [not included] as close to the

battery positive [+] terminal as possible with an ampere rating not to exceed the maximum current

specified on page 3

To remote wire from source unit.

The amplifier is turned“ON” remotely when vehicle`s source unit is turned “ON”