Southwire L6003 Bedienungsanleitung
INFARED MOTION
ACTIVATED SECURITY LIGHT
INSTALLTION INSTURCTIONS
Model # L6003
1 Year Warranty on Fixture
(Does not apply to bulbs, which have no warranty)
Congratulations and Thank You! The fixture you have purchased should give you 1
year of trouble free service. We take pride in the design and construction of each of our
products and work to maintain the quality of our materials and craftsmanship to assure
your satisfaction.
This product is warranted to be free of defects in workmanship and materials for a period
of 1 year from the original date of purchase. If any problems appear (other than burnt
out bulbs, which carry no warranty) within 1 year, the purchaser may return the item,
freight prepaid, together with a copy of your original purchase receipt to:
Southwire Co. 11290 80th Ave. Pleasant Prairie, WI 53158
Upon receipt of the item prepaid with a letter describing the problem, and a check for
$7.50 to cover return postage and handling, the company will, at its option, either repair
or replace the defective part or fixture at no charge to the purchaser. This warranty does
not apply to fixtures that have been used for rental or commercial purposes. It does not
cover fixtures that have been altered in any way or fixtures that have been subject to
misuse, accidents or damage in transit.
IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. NO CHARGES WILL BE ACCEPTABLE FOR
UNAUTHORIZED REPAIRS, PARTS OR SERVICE.
Some states do not allow limitations on how long an implied warranty lasts and do not
allow exclusions or limitations of incidental damages, so parts or all of this warranty
limitations or exclusions may not apply to you. Legal warranty rights will vary from state
to state and you may have other rights.
IMPORTANT NOTICE:
Every attempt has been made to deliver a quality product that will give you years of
trouble free service. In the event that you have problems with the fixture, please DO
RETURN TO PLACE OF PURCHASE. PLEASE CALL THE NUMBER BELOW FOR
BULB OR PARTS PROBLEMS:
(847) 672-4017
8-5 pm (West Coast time). All warranty problems are handled through Southwire Co.
HOW IT WORKS
Congratulations on the purchase of your Southwire Co. motion sensor light with infrared
detection. The motion detector turns lights on and off after sensing moving heat sources
in target area. Connected to light fixtures:
● Use as security light for any unprotected side or corner of house. Lights will be
activated when intruder passed through target area of sensor.
● Install as a sensing device to turn lights on as people approach the entrance of your
home.
● Functions as welcome light if installed to sense cars entering driveway.
PACKING INCLUDES
INSTALLATION
CHOICE OF LOCATION
Whenever possible, locate the unit so that its coverage area is away from heat sources
or reflective surfaces, such as heating vents, air conditioners, large moving trees or
pools of water. Whenever possible, locate the unit so that motion moves across the
coverage area, not directly towards or away from the motion sensor. It is because the
motion sensor is more sensitive to motion across it, not towards or away from it.
L6003 Motion Sensor Floodlight
3 Wire Connectors
Gasket
Mounting Bolt
Rubber Plug
Green wire screw & screw nut
(Additional accessory)
Cross Bar
Silicone(not included)
2 Screws
Note: The detection range specified above is based on the sensor’s performance in
conditions that represent average temperatures found in North America. The detection
range of the sensor will vary with changing ambient temperatures.
This fixture may be mounted on a wall or an eave. It may be mounted onto a
standard recessed outlet box or a wet location / outdoor outlet box. For easy
installation, replace an existing light fixture that is already connected to a wall switch.
WARNING: Maintain minimum 1.5” (3.8cm) distance between lampholders and sensor
head. Do not point lampholders directly at ceiling; possible fire hazard. Do not let lamps
touch ceiling. Keep a minimum 2” distance from ceiling.
TIPS FOR PROPER OPERATION
1. For optimal operation and optimal coverage area mount unit 6 to 8ft. above ground
on house overhang or wall.
2. Mount away from heat producing sources such as air conditioners & barbecue grills,
other light fixtures or sources of light. Keep in mind areas with traffic, pets or other
moving objects may cause nuisance triggering.
3. Do not aim at highly reflective surfaces such as smooth white walls, waterfalls, or
windows.
4. Point sensor slightly downward. Do not mount up facing sun.
5. If you are unfamiliar with electrical wiring, it is recommended you secure the services
of qualified electrician who can assure this installation meets national and local
electrical codes.
ASSEMBLY
If you already have outdoor lights in the location you intend to mount the new fixture,
you simply disconnect old fixture and remove. Follow steps for wiring the new units to
existing electrical box. If you do not have power to that location, a new outlet box and
wiring must be installed. DO NOT ATTEMPT TO DISASSEMBLE THE MOTION
SENSOR HEAD. THERE ARE NO USER SERVICEALE PARTS INSIDE. See
electrical wiring instructions for installation.
Remark: Fill in the wall plates and mounting surface with silicone.
CAUTION: Before beginning installation disconnect power to the location where the
light will be installed by shutting that controls the light is not sufficient to prevent
electrical shock.
WIRING THE LIGHT CONTROL
Fixture is pre-wired for quick and easy installation for both professionals and
do-it-yourself alike:
DO NOT REMOVE ANY CRIPMP CONNECTORS PREINSTALLED!! ONLY WHITE,
BLACK AND GREEN WIRES WILL NEED TO BE ATTACHED TO INCOMING LINES!!
1. Check local electrical codes before installation. Use only 120 Volt 60hz
power supply.
2. Be sure power is turned off at breaker or fuse box. Turning switch off is not sufficient
to prevent electrical shock!!
3. Remove old light fixture.
4. The new fixture mounts best on standard 4” octagonal electrical box. If your box is an
odd size, you may need to purchase an additional base in a proper size from an
electrical supplier. Check size carefully before attempting to mount fixture.
5. Slide the black foam gasket over the white, black and green wires. It seals the base
to the wall when installed, helping keep moisture out.
6. See diagram above:
A: Using wirenuts, connect white wire from fixture to white wire from house.
B: Connect black wire from fixture to black wire from house.
C: Connect green ground wire from motion detector to green ground wires from
fixture and house. In the event your wiring has no ground wire, contact a
qualified electrician to provide suitable ground.
D: All wirenuts installed to connect wired should be taped in place with
electrical tape to assure they cannot come off accidentally at a later time.
7. Install base of lamp to the 4” octagonal base using included screws. In the event your
box is deep in the walls, too deep for included screws, you may obtain longer screws
from local hardware store. Make sure you match threads correctly.
MAIN
CIRCUIT BREAKER OR FUSE
8. Wiring portion is now complete, so you can install bulbs. Again, double check wall
switch is in off position and power is shut off at breaker.
OPERATION
SET-UP AND ADJUSTMENT
Follow these steps to set up your security light for best operation.
1. Turn power switch on and wait 60 seconds for the system’s circuitry to stabilize.
2. Turn the “Time” knob to the fully counter clockwise direction.
3. Turn the “Range” control all the way in a counter clockwise direction.
4. Aim the control module to the desired target area. Have a person stand
approximately in the center of the target area moving slightly. Moving arms up and
down is usually sufficient.
5. Slowly rotate the “Range” knob clockwise until the lights go on. You may adjust the
“Range” control either way to the desired sensitivity level.
6. Turn the TIME knob clockwise to adjust how long you want the lights to stay on after
the unit is activated. The maximum (full clockwise) is about 10 minutes. The minimum
(full counter clockwise) is about 30 seconds.
Test Mode
Activate the photocell and allow the motion detector to
function in daylight for time setting.
Auto Mode Turn knob from 30 seconds to 10 minutes as needed.
Manual Override
Mode
Turn the wall switch Off-On twice within 2 seconds, the
lights will come on and stay on. After 6 hours, this option
will automatically return to Auto Mode.
Manual Override to
return to Auto Mode
During the light-on period in manual override mode, turn
the wall switch Off-On once within 1 second, this option
will reset sens or to Auto Mode.
Temperary On Mode
Turn the wall switch Off-On once within 1 second, the
lights will come on to support users' immediate need(light
on based on "Time" setting). Time will be reset to extend
the lights on.
Temperary On to
return to Auto Mode
During the light-on period in temperary on mode, turn the
wall switch Off-On three times within 3 seconds, this
option will reset sensor to Auto Mode.
LED Indicator
1.During the warm-up time, LED is on until warm-up finish.
2.During Test Mode, LED is the indicator to show user in
the detection zone. When the sens or is triggered, the light
is on, and LED starts flash. When user is out of detection
zone, LED stops flash.
3.LED is always flash slowly to warn the intruder.
SPECIFICATIONS
TROUBLESHOOTING
Lights do not come on at all:
1. Make sure the breaker for the fuse is in the on position.
2. Make sure the switch in the house is turned on.
3. Check to see there is power to the motion detector on the black and white wires from
the house.
4. Make sure the lamps being used are working. Faulty bulbs, or fiber washer at bottom
of screw-type bulbs will prevent proper contact.
5. Check all wiring and connections.
A: All white wires
B: Black house wire to black motion detector wire.
C: Ground wires.
Lights stay on all night
1. The dusk-to-dawn photocell feature. Make sure daylight is normal (N) position for
motion detection.
2. Check all wiring and connections.
A: All white wires
B: Black house wire to black motion detector wire.
C: Ground wires.
3. Check to make sure each lamp is minimum 40 watts and total does not exceed
total 500 Watts.
Motion Detector triggers on with motion, and stays on:
1. Move floodlights away from motion detector head, or use lower wattage lamps.
2. If mounted on slope, aim slightly upward if slope is upward. If on downward slope,
aim motion detector head severely downward, and slowly raise if necessary. Adjust
during day using test mode.
3. Adjust Range sensitivity adjustment. Do not use this adjustment to compensate for
poor aiming.
Sensor Range Up to 70 ft.(21m)
Sensing Angle 180 degree + Downward detection
Power Consumption 4 watts maximum(control module only)
Power Requirement 110/120 volts 60 Hz
Load Rating 500 watts maximum (Incandescent only)
Operating Modes TEST, AUTO, MANUAL, and Temperary ON Mode
Delay Control 30 seconds to 10 minutes (approximately)
LED Indicator 1 piece LED for Test Mode indicator & intruder watcher
4. Aim motion detector head lower, away from moving busy areas such as sidewalks
and streets.
Motion Detector comes on randomly, or blinks in test mode.
1. Move floodlights away from motion detector head, or use lower wattage lamps.
2. Aim motion detector head lower.
3. Make sure motion detector head is not aimed at heating/cooling ducts, metal sheds,
pools of water, windows, or smooth walls.
4. Adjust Range sensitivity setting.
5. Make sure motion detector is mounted on firm surface, as mechanical vibrations can
cause false triggering.
NOTE: Occasionally, in severe frigid temperatures flows of warm air passing the motion
detector may cause light to cycle on and off due to extreme temperature change. This is
not a sign of a problem. This infrequent occurrence will not affect normal operation of
unit.
Not enough or too much detection range
1. Adjust Range sensitivity setting to desired level.
Inhaltsverzeichnis
Andere Southwire Scheinwerfer Handbücher
Beliebte Scheinwerfer Handbücher anderer Marken
VIZULO
VIZULO Micro Martin Benutzerhandbuch
EuroLite
EuroLite LED IP FL-100 SMD Bedienungsanleitung
Cooper Wheelock
Cooper Wheelock XB12 Bedienungsanleitung
Allen + Roth
Allen + Roth 17624-000 Bedienungsanleitung
ADJ
ADJ 4 STAGE PAK Bedienungsanleitung
Cooper Lighting
Cooper Lighting EGL91SW233 Bedienungsanleitung
