SPACE HD MOD-HDMI-Q Bedienungsanleitung
Quad Full HD
DVB-T Modulator
4x HDMI to 4x DVB-T (COFDM)
“Home” modulator
MOD-HDMI-Q
HELPLINE 0861 40 41 42 • www.spacetv.co.za
OPERATION MANUAL
MOD-HDMI-Q : Operation Manual 1v0
HELPLINE 0861 40 41 42 • www.spacetv.co.za
MOD-HDMI-Q : Operation Manual 1v0
IMPORTANT SAFETY PRECAUTIONS INFORMATION
READ THE FOLLOWING WARNINGS BEFORE YOU USE YOUR DEVICE
1. WARNING
The following safety precautions must be observed to prevent re or electric shock
hazard. Safety precautions include but are not restricted to the following:
POWER SUPPLY / MAINS CORD
• Operate the unit only within the voltage range dened as appropriate by the
manufacturer.
• Occasionally check the power connector and remove dirt or dust that may have
accumulated.
• Use only the mains cord that comes with your unit.
• Do not operate the unit or plug in the mains cord if it is broken, split, or damaged in
any way.
• Do not place the mains cord next to heating devices. Do not pull it, place heavy
objects on it or damage it in any way. Keep it out of reach of children.
• Ensure that the device is plugged in a properly grounded socket. Insucient
grounding may cause electrocution.
• Always carefully disconnect all plugs by pulling on the plug and not on the cord.
Make sure the unit’s power switch is turned o before removing the cord from an
outlet.
• Disconnect the mains cord when the unit is not in use for long periods of time or
during storms.
• Do not connect the unit to a multiple-outlet to avoid plug overheating.
DISASSEMBLING
• This unit contains parts that cannot be repaired by the user. Do not disassemble or
try to repair it as this will void all warranties. Please contact the manufacturer if you
experience any problems with your unit.
WATER/HUMIDITY
• Do not keep the unit in a humid place or near water.
• Do not plug/unplug the unit with wet hands.
FIRE
• Never place a candle or another source of re on the unit as it may fall and start a re.
• If the mains cord or the power connector is damaged or destroyed, or if there is a
sudden loss of picture during operation, or if you notice a strange smell or there is
smoke, immediately switch the unit o, disconnect the mains cord and contact the
manufacturer’s technical support department.
HELPLINE 0861 40 41 42 • www.spacetv.co.za
MOD-HDMI-Q : Operation Manual 1v0
INSTALLATION / STORAGE
• This unit contains high precision pieces of electronics. To ensure optimal
performance and avoid damage, do not store it in any location where it may collect
dirt, duct, lint, etc. Do not expose it to extreme heat or cold (e.g. in direct sunlight,
near a heater or in the car during the day). Place the unit in a secure place to avoid
falls.
• Before moving the unit, always unplug all cords rst.
• When installing the unit, make sure that an outlet is within easy reach. In case of
malfunction, switch the unit o and unplug the power cord. When the unit is not in
use for a long period of time, make sure that the mains cord is disconnected.
CONNECTIVITY
• Before connecting the unit to other electronic devices, always switch o and unplug
all devices.
MAINTENANCE
• Do not spill liquids on the unit. Do not use any diluents or volatile liquid to clean
the unit. Instead, use a soft slightly damp cloth and allow the unit to dry completely
before using again.
HANDLING
• Do not poke your nger into the openings on your unit.
• Never put paper, metal parts or other objects into the openings of your unit. If you
suspect that there are foreign parts in your unit, switch it o and unplug the mains
cord. Contact the manufacturer’s technical support department.
• Do not step on or place heavy objects on top of the unit. To avoid hardware damage,
handle all buttons, connectors and switches gently.
HELPLINE 0861 40 41 42 • www.spacetv.co.za
MOD-HDMI-Q : Operation Manual 1v0
2. INTRO
Congratulations on purchasing the MOD-HDMI-Q. You now own a high quality, “Home”
DVB-T HD modulator. To get the most out of your purchase, please take the time to
carefully read through this manual.
3. INSTRUCTIONS
3.1 DESCRIPTION
The MOD-HDMI-Q is a high quality quad DVB-T “Home” modulator which accepts
four HDMI inputs and converts them into four RF DVB-T channels on its output.
The excellent picture (Full HD 1920*1080-30p) and modulation quality (MER~35dB)
renders the MOD-HDMI-Q the ideal solution for distributing SD/HD digital signals
coming from e.g. a DVD player, STB or camera in a CATV network using the DVB-T
technology.
The user has the ability to control the device by either using the onboard SSD (Seven
Segment Display) interface and keypad for quick installation or by using the USB
interface with the appropriate for advance programming.
Finally, the MOD-HDMI-Q’s metal case provides excellent electromagnetic shielding
as well as great temperature dissipation and rigidness.
3.2 FEATURES
• 4 x DVB-T RF out
• High quality and performance
• Very clean RF spectrum
• MER value ~ 35dB
• RF output frequencies 174...862MHz
• H.264 HD encoder bitrate 1-19Mbps
• HDCP support
• User friendly interface for quick installation
• USB interface for advanced programming
• External power supply
3.2.1 AUTORESET FUNCTIONS AND WATCHDOG
During the normal operation of the MOD-HDMI-Q, the main CPU monitors all
the internal parts in order to ensure that the device works normally. In case of an
internal error or module failure, the MOD-HDMI-Q immediately initiates the recovery
procedure by resetting the appropriate module or the device. Finally, watchdog
timers ensure that the device will be reset in case of CPU failure.
HELPLINE 0861 40 41 42 • www.spacetv.co.za
MOD-HDMI-Q : Operation Manual 1v0
3.2.2 BUTTONS LOCKMECHANISM
The MOD-HDMI-Q will lock the functionality of its buttons after 5 min idle time to
avoid of being pushed accidentally. Two red dots on the SSD notify the user that
the button interface is locked. To unlock it, the user must press simultaneously the
UP + DOWN buttons for 5sec approximately
3.2.3 DIGITAL ATTENUATOR
The MOD-HDMI-Q has an embedded digital attenuator. The user is able to select
between three dierent attenuation steps as follows:
1. 0 dB attenuation (Output level: 90dbμV) SSD will display: “00”
2. 10 dB attenuation (Output level: 80dbμV) SSD will display: “10”
3. 25 dB attenuation (Output level: 65dbμV) SSD will display: “25”
3.2.4 HDCP ON/OFF FUNCTION
By pressing the “Channel / Prole” button for more than 5sec the user enables the
HDCP ON/OFF function. The SSD will display this status as follows:
1. H1 : Indicating that the HDCP is ON
2. H0 : Indicating that the HDCP is OFF
Using the Up/Down buttons the user is able to select one of the above status to
enable/disable the HDCP function. The MOD-HDMI-Q will exit from the current
functionality after being idle for more than 2-3sec.
3.2.5 USB INTERFACE FOR ADVANCE PROGRAMMING
The MOD-HDMI-Q provides a USB interface with the appropriate software for
advanced programming. For more information please read Appendix A.
3.3 BLOCK DIAGRAM
4 x H.264
encoders
(Up to 1080-30p) 4 x RF DVB-T out
Mux + 4 x
DVB-T
Modulators
HDMI in
1 32 4
HELPLINE 0861 40 41 42 • www.spacetv.co.za
MOD-HDMI-Q : Operation Manual 1v0
1. Channel or Prole selection
button
2. Seven Segment Display
3. UP / DOWN buttons
4. LED indicators
a. Lock:
ON when HDMI
communication has been
established
b. Channel:
ON when “Channel” mode is
selected
c. Attenuation:
ON when “Attenuator” mode
is selected
d. Channel:
ON when “Prole” mode is
selected
5. Modulator selection button
6. HDMI input for modulator Νο 1
7. HDMI input for modulator Νο 2
8. USB port for advanced
programming
9. HDMI input for modulator Νο 3
10. HDMI input for modulator Νο 4
11. +12VDC / 2A PSU input
12. Choice indication LED for
modulator Νο 3
13. Choice indication LED for
modulator Νο 4
14. Choice indication LED for
modulator Νο 1
15. Choice indication LED for
modulator Νο 2
3.4 FRONT PANEL
Figure No 1
HELPLINE 0861 40 41 42 • www.spacetv.co.za
MOD-HDMI-Q : Operation Manual 1v0
3.5 INSTALLATION
The MOD-HDMI-Q can be programmed with one of the following ways:
• Fromthefrontpaneldisplay
• FromtheUSBinterface
3.3.1 Installation using the Front panel display:
The user is able to install very quick and easy multiple MOD-HDMI-Qs using the SSD
+ Button interface of the front panel of the device, following the steps below:
STEP 1:
Power up the MOD-HDMI-Q by adding the external power supply. The MOD-HDMI-Q
will need 40-50secs to initialize itself. The SSD (Seven Segment Display – No 2 / Figure
No1 ) depicts the initialization status.
STEP 2:
Choose a modulator by pressing the MOD Select button (No 5 / Figure No.1). The LED
display will turn on depending on the modulator that is selected.
Step 3:
Choose “Channel mode” by pressing the Channel/Prole button (No 1 / Figure No.1 )
The “Channel LED” will lit indicating that “Channel” selection mode is selected.
Step 4:
Choose “Attenuation mode” by pressing the Channel/Prole button (No 1 / Figure
No.1 ) The “Attenuation LED” will lit indicating that “Attenuation” selection mode is
selected.
Step 5:
Choose “Prole mode” by pressing the Channel/Prole button (No 1 / Figure No.1 )
The “Prole LED” will lit indicating that “Prole” selection mode is selected.
Step 6:
Repeat the procedure from step Νο 2 up to step Νο 5 for the rest of the modulators
of the MOD-HDMI-Q.
HOW PROFILES WORKS
In an installation all the modulators (or Mux in general) need to have dierent values of
the following elds to avoid conicts in the automated scan of the TV sets:
Program Name Service ID TS ID
For that reason, the user must always selects a dierent Prole number in every modulator
starting from Number #1.
HELPLINE 0861 40 41 42 • www.spacetv.co.za
MOD-HDMI-Q : Operation Manual 1v0
Eg. Let’s say we want to install three modulators in a CATV network. In step No 4 we will
choose:
• Prole No 1 for the 1st modulator
o meaning: Program Name = DTV 1
o meaning: Service ID = 1
o meaning: TS ID = 2240
• Prole No 2 for the 2nd modulator
o meaning: Program Name = DTV 2
o meaning: Service ID = 2
o meaning: TS ID = 2241
• Prole No 3 for the 3rd modulator
o meaning: Program Name = DTV 3
o meaning: Service ID = 3
o meaning: TS ID = 2242
As a result, all the above modulators have dierent values in the above elds.
Caution!!!
• Every time we choose a dierent Prole number, the MOD-HDMI-Q will apply a full
reset to itself that will last for 40-50 seconds.
• Using the USB interface, we have the ability to add custom values to the above elds.
3.3.2 Installation using the USB interface:
The MOD-HDMI-Q provides a USB interface with the appropriate software for advanced
programming.
System requirements
• Windows XP (SP1 or higher)
• Windows Vista
• Windows 7 (32 & 64bit)
• Windows 8 (32 & 64bit)
• Windows 10 (32 & 64bit)
Device connection via software
1. Download the appropriate software from www.spacetv.co.za and run it.
2. Connect the MOD-HDMI-Q via the USB cable (A-male to B-male type) and wait
until the drivers are installed.
3. In case Windows cannot install the USB drivers automatically, when prompt,
insert the correct path of the folder named “USB drivers”, which contains the
MOD-HDMI-Q USB drivers.
4. Once Windows have successfully installed the USB drivers of the MOD-HDMI-Q, a
pop-up message appears to verify this process.
5. Run the Lemco GUI xxx.exe le and the main screen will appear (Figure No 2):
HELPLINE 0861 40 41 42 • www.spacetv.co.za
MOD-HDMI-Q : Operation Manual 1v0
Software guidelines
1. From the “ComPort” combo box choose the correct USB port that connects the
MOD-HDMI-Q and press “Connect”.
2. Once the software has successfully connected with the device, it will
automatically download all the settings of the MOD-HDMI-Q.
3. The Lemco GUI xxx.exe consists of ve sub-categories as described below:
• DVB-T Settings – Parameters regarding the modulator part
• Encoder Settings – Parameters regarding the H.264 encoder
• Multiplexer Settings – Parameters regarding the multiplex part
• System Settings – Parameters regarding system information
• Selected input – Modulator selection (Νο1, Νο2, Νο3, Νο4)
1. DVB-T Settings
In this category the user is able to adjust several parameters of the modulator RF
output part, as described below:
1.1 Channel - Output channel selection (VHF:5-12 & UHF:21-69)
1.2 Bandwidth - Bandwidth selection
1.3 Constellation - Constellation selection
1.4 Modulation - Modulation selection
1.5 Guard Interval - Guard Interval selection
1.6 Code rate - Code rate selection
Figure No 2
HELPLINE 0861 40 41 42 • www.spacetv.co.za
MOD-HDMI-Q : Operation Manual 1v0
2. Encoder Settings
In this category the user is able to adjust parameters of the H.264 encoder, as
described below:
2.1 Input source – Select the primary input source
2.2 Video BR (Mpbs) – Set the video bitrate
2.3 Audio BR (Kbps) – Set the audio bitrate
2.4 Audio Encoding – Select the audio encoding
2.5 HDCP ON/OFF – Enables/disables HDCP
2.6 Output Video Res – Select ouput video resolution
3. Multiplexer Settings
In this category the user is able to adjust parameters of the MOD-HDMI-Q
multiplexer, as described below:
3.1 Network Name + ID – Enter the Network name + ID*
3.2 Program Name + ID – Enter the Program name + ID
3.3 Provider Name - Enter the Provider name
3.4 Original Net ID - Set the Net ID (0-65535)*
3.5 TS ID - Set the Transport Stream ID (0-65535)*
3.6 PMT PID – Set the PID value
3.7 Video PID – Set the Video PID value
3.8 Audio PID – Set the Audio PID value
3.9 LCN No – Set the LCN No (1-999) (must be enabled rst)
3.10 LCN Provider - Set the LCN provider
* TS ID must always be dierent between DVB-T modulators in the same network.
Caution!!!
• Modulation settings must be applied with care and in order to have adequate
output bitrate. The output bitrate (which can be calculated from the tables in
Appendix B) must be equal or greater than the total sum of the bitrate of the
encoders.
Example: Assuming we select the following modulation settings:
Modulation: 8K
Constellation: 16-QAM
Code Rate: 5/6
Guard Interval: 1/32
Bandwidth: 8MHz
• We have an output bitrate of 20.107 Mbps according to Appendix B.
• This means that encoder’s bitrate must be adjusted in such a way that the
total bitrate of the encoder does not exceed the 20.107MBps limit, otherwise
artifacts may occur.
• For example, one valid selection in case of four encoders would be to set each
encoder bitrate to 5Mbps since: 4 x 5Μbps = 20Mbps < 20.107MBps
Inhaltsverzeichnis
