SPACEMAKER EL64 Bedienungsanleitung
ASSEMBLY INSTRUCTIONS FOR
MODELS
EL64, EL65, EL66, EL67, EL69
EG64H-A, EG65H-A, EG66H-A, EG67H-A, EG69H-A
HE64, HE65, HE66, HE67, HE69 AL01
15-5710507 English/French 05/07
EASY TO INSTALL
Manufactured by Spacemaker Limited
CAUTION: Some parts have sharp edges. Care must be taken when handling
the various pieces to avoid a mishap. For safety sake, please read the safety
information provided in this manual before beginning construction. Wear
gloves when handling metal parts.
100%CANADIAN
2
AH02
CONTENTS
•Pre-construction instructions • Anchoring the frame
•Assembling the building • Parts List and order information
PROCEED WITH CONFIDENCE
It might look complicated when you first unpack your building…but it really isn’t. Simply follow the
illustrated instructions and your building will go up quickly and accurately.
ASSEMBLY INSTRUCTIONS
•Before beginning construction...check local building codes regarding footings, location
and other requirements. Study and understand the owner's manual.
•You will need assistance…you’ll find that another person will speed the job and make
assembly easier.
•Selecting your site…choose an area that’s firm and level yet allows drainage away from
site.
WARNING! … DO NOT ERECT YOUR BUILDING IN AREAS THAT ARE SUBJECTED TO
HIGH WINDS, OR ERECT ON A WINDY DAY. ANY BUILDING LEFT PARTIALLY CON-
STRUCTED MAY BE SERIOUSLY DAMAGED IF LEFT IN THIS STATE.
•Sort and separate all parts and hardware…checking with the Parts List on Page 4 and
the illustrations on Page 5…be sure you have all parts and know where they belong in the
building. Each part has been numbered or illustrated, the quantity required and its part
number noted.
Foundation Preparation
• Hammer and Nails
• Spade or Shovel
• Hand Saw / Power Saw
• Lumber and/or Concrete
Optional Time-Savers
• Wrench / Nut Driver
• Electric / Cordless Drill
• Square
• String (for squaring frame)
Required
• Utility Knife / Scissors
• Pliers
• Carpenter's Level
• Tape Measure
Required
• Eye Goggles
• No. 2 Phillips Screwdriver
(with Hardened Magnetic Tip)
• Work Gloves
• Step Ladders
BUILDING CARE
•Carefree maintenance – Your building has been designed to give you years of carefree
service. All parts have been precision engineered for a perfect fit. It is manufactured from
heavily galvanized steel with exterior parts pre-enameled on both sides at the steel mill.
•IMPORTANT – This building is designed to withstand normal wind loads when
installed according to instructions. Manufacturer cannot be held responsible for
any consequences due to buildings that are not installed per instructions or for
damage due to weather conditions or acts of God.
•Follow step-by-step instructions carefully…complete
each step before going onto the next one.
•Retain this manual after assembly is completed…it
contains a complete parts list.
L03
IMPORTANT
PERSONAL SAFETY DURING BUILDINGS CONSTRUCTION
Some of the building components may contain sharp edges prior to assembly. Wear protective
work gloves while handling these components. Wear eye protection when using any form of power
tool. Do not use household voltage power tools in a wet or damp environment. Household voltage
power tools must be monitored and controlled by a Ground Fault Interrupter or more commonly
called a G.F.I. Do not use any part of the building's frame as a means of personal support while
attaching components during assembly.
PREPARATION OF BUILDING SITE
This building must be constructed on a SOLID
BASE FOUNDATION. We recommend a
poured concrete pad or large size concrete
patio stone squares for a suitable floor and
base. Which ever you select…make sure your
foundation area is firm and level and will allow
drainage away from the site. Make your solid
base foundation at least 4” (100mm) larger than
your building. The manufacturer is not re-
sponsible for the choice and the construc-
tion of the foundation.
NOTE: For a concrete pad base, prepare a
level bed for a firm footing layer of crushed
stone. The concrete pad should then be poured
to a thickness of 4” (100mm) to 5” (125mm).
When completed, allow to dry thoroughly for at
least 48 hours.
YOUR BUILDING MUST BE
ANCHORED
Your building must be firmly anchored to your concrete
pad or large concrete patio stone squares…to help
protect against damage in high winds.
FURTHER ANCHORING INSTRUCTIONS
FOLLOW AFTER ALL WALL AND ROOF
PANELS HAVE BEEN INSTALLED.
MODEL "A" "A" "B" "B"
CM INCH CM INCH
6x4 172.7 68 114.9 45 1/4
6x5 172.7 68 146.1 57 1/2
6x6 172.7 68 177.2 69 3/4
6x7 172.7 68 208.3 82
6x9 172.7 68 270.5 106 1/2
3
OUTSIDE MEASUREMENTS OF BUILDING AT BASE
“B” + 100mm (4")
MINIMUM
“A” + 100mm (4")
MINIMUM
DOORWAY
Part Part Quantity
Number Description 6x4 6x5 6x6 6x7 6x9
64H Rear Base Rail 2 2 2 2 2
53H Side Base Rail - 2 - - 4
63H Side Base Rail - - 2 - -
73H Side Base Rail 2 - - 4 -
62H Front Base Rail 2 2 2 2 2
610H Entry Ramp 1 1 1 1 1
* Corner Panel 2 2 2 2 2
* Half Corner Panel (Front Only) 2 2 2 2 2
640H Rear Top Rail 2 2 2 2 2
527M Side Top Rail - 2 - - 4
627M Side Top Rail - - 2 - -
727M Side Top Rail 2 - - 4 -
66H Door Track 2 2 2 2 2
635H Door Fascia 1 1 1 1 1
69G DoorJamb 2 2 2 2 2
628H Front Midwall Brace 2 2 2 2 2
* Wall Panel 3 5 5 7 9
* Half Wall Panel 2 - 2 - -
640H Rear Midwall Brace 2 2 2 2 2
527M Side Midwall Brace - 2 - - 4
627M Side Midwall Brace - - 2 - -
727M Side Midwall Brace 2 - - 4 -
* Left Gable 2 2 2 2 2
* Right Gable 2 2 2 2 2
516L Main Ridge Beam - 2 - - -
616L Main Ridge Beam - - 2 - -
H716H Main Ridge Beam 2 - - 4 -
H516H Main Ridge Beam - - - - 4
618H Left Roof End Panel 2 2 2 2 2
644H Right Roof End Panel 2 2 2 2 2
* Roof Panel 2 4 4 6 8
* Half Roof Panel 2 - 2 - -
420H RidgeCover 1 - - - -
520H RidgeCover - 1 - - 1
620H RidgeCover - - 1 - -
720H RidgeCover - - - 2 -
920H RidgeCover - - - - 1
541H Roof Edge Trim - 2 - - 4
641H Roof Edge Trim - - 2 - -
741H Roof Edge Trim 2 - - 4 -
* Door Panel 2 2 2 2 2
DISO3 DoorStrengthener 4 4 4 4 4
623 Horizontal Door Brace 2 2 2 2 2
632 Top & Bottom Door Brace 4 4 4 4 4
* Weatherseal Tape 1 1 1 1 1
49H Ridge Cover End Cap 2 2 2 2 2
* DoorHandle 2 2 2 2 2
* Plastic Washer Tree 2 2 2 2 2
Owner'sManual 1 1 1 1 1
Hardware Kit Contains
(Bolts, Nuts and Screws)
* Roof Corner Cap 4 4 4 4 4
* Door Spacer (2 sets of 2) 4 4 4 4 4
A67 Door Glide 4 4 4 4 4
AL04
4
* Indicates that part number is NOT stamped in the part see illustrations.
Painted parts may contain a prefix that designates color / material.
Parts List
IMPORTANT...When ordering parts please provide number stamped on the surface of galvalized parts. In the case of wall
and roof panels please provide the model number of the building, color and size of panels.
To order parts please use order form on the last page.
Parts Not Identified with Part Number
L05
5
CORNER PANEL HALF CORNER PANEL WALL PANEL HALF WALL PANEL
LEFT GABLE RIGHT GABLE
ROOF PANEL HALF ROOF PANEL
ROOF CORNER
CAP
DOOR PANEL
WEATHERSEAL TAPE DOOR HANDLE PLASTIC WASHER TREE
ITEMS in the HARDWARE BAG
DOOR SPACER DOOR GLIDE
A67
SIDE AND REAR BASE RAILS
Assemble lengths of side base rails (2 pcs.)
together with a lap joint. Align large holes.
Repeat for other side.
NOTE - for product sizes 6x4, 6x5 and 6x6
these parts are in one full length piece.
Repeat above procedure to assemble lengths
of rear base rails No. 64H (2 pcs.).
STEP
11
11
1
6
L06
INSIDE
USE SELF TAPPING SCREWS..10mm (3/8") LONG
See Pages 4 and 5 for profile,
correct part number and quantity
required for your building.
OUTSIDE SIDE BASE RAIL
LARGE
6mm (1/4") HOLES
SIDE BASE RAIL
USE 10mm (3/8") LONG BOLTS AND NUTS
VIEWED FROM
INSIDE BUILDING
INSIDE
OUTSIDE
ENTRY RAMP
No. 610H
FRONT BASE RAIL
No. 62H
FRONT BASE RAIL
No. 62H
VIEWED FROM
INSIDE BUILDING
WIDE FLANGE ON OUTSIDE
FRONT BASE RAILS AND ENTRY RAMP
Space out lengths of front base rails No. 62H (2 pcs.) and
fasten entry ramp No. 610H between lengths.
STEP
22
22
2
1.
2.
1.
BASE FRAME ASSEMBLY
Assemble all 4 base rails into a base frame in proper position
on your foundation. Use 10mm (3/8") self tapping screws on
front and on back corners.
Check base frame for squareness by measuring diagonal
corners. Your measurements should be equal. See "A"
STEP
33
33
3
7
E07
BACK CORNER
REAR BASE RAIL
DOORWAY
SOLID
FOUNDATION
"A"
FRONT CORNER
FRONT BASE RAIL AND
ENTRY RAMP
SIDE BASE RAIL
DOORWAY
* AFTER ASSEMBLY CHECK BASE DIMENSIONS (SEE PAGE 3) TO VERIFY CORRECT POSITION OF RAILS.
USE SELF TAPPING SCREWS...10mm (3/8") LONG
* AFTER ASSEMBLY CHECK BASE DIMENSIONS (SEE PAGE 3) TO VERIFY CORRECT POSITION OF RAILS.
WARNING!
DO NOT ERECT ON A WINDY DAY. THE LARGE WALL
ANDROOFPANELSPROVIDEALARGESURFACEAND
THE WIND COULD EASILY CARRY THEM AWAY. ANY
BUILDING LEFT PARTLY CONSTRUCTED MAY BE SE-
RIOUSLY DAMAGED IF LEFT IN THIS STATE.
1.
2.
STEP
44
44
4
8
L08
SIDE AND REAR TOP RAILS
Assemble lengths of side top rails (2 pcs.) together with a lap joint...see
"A". Fasten to top of corner panels. Repeat for other side. NOTE - for
sizes 6x4, 6x5 and 6x6 these parts are in one full length piece.
Repeat above procedure to assemble and fasten lengths of rear top rail
No. 640H (2 pcs.)...See "B".
STEP
55
55
5
USE SELF TAPPING SCREWS
...10mm (3/8") LONG
CORNER PANELS
Position rear corner panels and fasten to rear
and side base rails...with narrow flange of
panel along the side of the building.
Position front half corner panels and fasten to
front and side base rails...with narrow flange
of panel along the side of building.
See Pages 4 and 5 for profile,
correct part number and quantity
required for your building.
DOORWAY
REAR
SIDE
SIDE TOP RAIL
REAR TOP RAIL
No. 640H
SIDE
"A"
REAR "B"
USE 10mm (3/8") LONG
BOLTS AND NUTS
1.
2.
1.
2.
STEP
66
66
6
9
L09
DOOR TRACK INSTALLATION
Install 4 door glides No. A67 into door track. See "A"
Fasten door track to the front corner panels with screws.
IMPORTANT: PLACE EDGE OF DOOR TRACK WITH
THE MOST HOLES FACING THE OUTSIDE.
STEP
77
77
7
USE SELF TAPPING SCREWS...10mm (3/8") LONG
SPLICED ASSEMBLY OF DOOR
TRACK AND DOOR FASCIA
Assemble lengths of door track No. 66H
(2 pcs.) together with door fascia No. 635H. See Pages 4 and 5 for profile,
correct part number and quantity
required for your building.
FRONT
SIDE
Door Track
"A"
DOOR GLIDE
No. A67
DOOR FASCIA No. 635H
MOST HOLES ON THIS SIDE
MOST HOLES ON THIS SIDE DOOR TRACK
No. 66H
VIEWED FROM INSIDE
DOORWAY
SLIDE DOOR GLIDES
INTO DOOR TRACK
INSIDE
OUTSIDE
USE SELF TAPPING SCREWS...10mm (3/8") LONG
1.
2.
1.
STEP
88
88
8
10
AL10
DOOR JAMBS AND FRONT MIDWALL BRACE
Remove corner panel screws as necessary and install door jambs No. 69G on
each side of entry ramp...sliding door jamb under the half corner panel and
under door fascia. Fasten at base rail --- then fasten through the door fascia and
door jamb into the side of door track. Replace half corner panel screws.
Fasten door jamb to half corner panels at midwall height with 10mm (3/8") bolts
andnuts.
Install front midwall brace No.628H on each side of doorway.
Use short bolts 6mm (1/4").
DOOR TRACK
USE SELF TAPPING SCREWS...10mm (3/8") LONG
DOOR FASCIA
DOOR JAMB
No. 69G
DOOR FASCIA
DOORWAY FRONT MIDWALL BRACE
No. 628H
USE SHORT 6mm (1/4") BOLTS AND NUTS
DOOR JAMB
No. 69G
1.
2.
3.
Dieses Handbuch passt für folgende Modelle
14
Inhaltsverzeichnis
Andere SPACEMAKER Außenlagerung Handbücher
SPACEMAKER
SPACEMAKER RGB1010ONEU Gebrauchs- und Pflegehandbuch
SPACEMAKER
SPACEMAKER 90174CL Series Gebrauchsanweisung
SPACEMAKER
SPACEMAKER PS63EU Gebrauchsanweisung
SPACEMAKER
SPACEMAKER PS53 Gebrauchsanweisung
SPACEMAKER
SPACEMAKER RPT84ONEU Gebrauchs- und Pflegehandbuch
SPACEMAKER
SPACEMAKER Versa-shed VRS53AN01 Bedienungsanleitung
SPACEMAKER
SPACEMAKER PS63 Gebrauchsanweisung
SPACEMAKER
SPACEMAKER RGB1012ONEU Gebrauchs- und Pflegehandbuch
SPACEMAKER
SPACEMAKER PS63 Gebrauchsanweisung
SPACEMAKER
SPACEMAKER RGB108ONEU Gebrauchs- und Pflegehandbuch
SPACEMAKER
SPACEMAKER RGB88ONEU Gebrauchs- und Pflegehandbuch
SPACEMAKER
SPACEMAKER VERSA-SHED EVRS63 Gebrauchsanweisung
SPACEMAKER
SPACEMAKER PS43EU Series Gebrauchsanweisung
SPACEMAKER
SPACEMAKER SBS64EU Bedienungsanleitung
SPACEMAKER
SPACEMAKER VERSA-SHED EVRS53 Series Gebrauchsanweisung
SPACEMAKER
SPACEMAKER RGB86ONEU Gebrauchs- und Pflegehandbuch
Beliebte Außenlagerung Handbücher anderer Marken
Lifetime
Lifetime 6418 Bedienungsanleitung
rollaway container
rollaway container ARPCA24 Bedienungsanleitung
Duratuf
Duratuf Havelock Bedienungsanleitung
X-METAL
X-METAL 4065 Bedienungsanleitung
Outdoor Life Products
Outdoor Life Products FP2030 F Bedienungsanleitung
Royalcraft
Royalcraft Faro 295L Storage Box Bedienungsanleitung
