Spartan 1065 Bedienungsanleitung

SPSP

SPARTART

ARTART

ARTANAN

ANAN

Spartan Tool L.L.C.

800.435.3866

www.spartantool.com

Record the Serial Number of your

Model 1065

and give the number to the factory when

ordering parts.

Serial

Number_________________________

MODEL 1065

Owner’s Manual

44292000 (Rev. E) 4/03/13

Page 2

Warning

SPARTAN TOOL L.L.C.

1506 W. Division Street

Mendota, IL 61342

800 435 3866 Fax 888 876 2371

www.spartantool.com

— Read the safety and operating instructions before using any Spartan Tool products. Drain and

sewer cleaning can be dangerous if proper procedures are not followed and appropriate safety

gear is not utilized.

— Before starting unit, be sure to wear personal protective equipment such as safety goggles or

face shield and protective clothing such as gloves, coveralls or raincoat, rubber boots with metatarsal

guards, and hearing protection.

— Drains and sewer can carry bacteria and other infectious micro-organisms or materials which

can cause death or severe illness. Avoid exposing eyes, nose, mouth, ears, hands and cuts and

abrasions to waste water or other potentially infectious materials during drain and sewer cleaning

operations. To further help protect against exposure to infectious materials, wash hands, arms and

other areas of the body, as needed, with hot, soapy water and, if necessary, flush mucous membranes

with water. Also, disinfect potentially contaminated equipment by washing such surfaces with a hot

soapy wash using a strong detergent.

— For any questions contact the company at the address shown below.

“California Prop. 65: This product may contain an extremely small amount of lead in the coating.

Lead is a material known to the State of California to cause cancer or reproductive toxicity.”

Page 3

Table of Contents

OPERATING SECTION

Introduction ---------------------------------------- 4

Service Information ------------------------------ 4

Specifications and Features ------------------- 5

Safety Instructions ----------------------------- 6-9

Machine Features ------------------------------- 10

Assembly Instructions --------------------- 10-13

Operating ------------------------------------ 14-16

Operating the Power Cable Feed ----------- 16

Special Applications Procedure ------------- 17

Maintenance Instructions ----------------- 18-21

PARTS SECTION

Final Assembly------------------------------ 22-24

Drum Assembly ---------------------------------- 25

PM Motor Cover Assembly-------------------- 26

Frame Assembly --------------------------- 27-29

Distributor Arm Assembly --------------------- 30

Cable Guide Assembly ------------------------ 31

1065 PM Motor Assy --------------------------- 32

Motor Support Assy ------------------------ 33-34

Forward Reverse Switch ---------------------- 35

E-Z Lift Dolly -------------------------------------- 35

3/4” Cable----------------------------------------- 36

.66 Universal Anchor Assy. -------------------- 37

Air Foot Switch ---------------------------------- 37

.66 Magnum Cable ----------------------------- 38

Cable Safety Guide----------------------------61-62

Introduction --------------------------------------- 44

Attaching the Cable Safety Guide ----------- 45

Setting Your Cable Size ----------------------- 46

04221000 Universal Power Feed ---------- 47

04217500 Power Feed Assembly ----------- 48

04224000 Bearing Block Assy (Long) ----- 49

44219900 Bearing Block Assy (Short) ----- 50

44119600 Wheel Carrier Body (Long) ----- 51

44119700 Wheel Carrier Body (Short) ----- 51

Model 1065 & 2001 Installation ------------- 52

Model 200 and 300 Installation ------------- 53

Model 100 Installation ------------------------- 54

Operating Instructions ------------------------- 55

Cleaning Operation ----------------------------- 56

Disassemble & Reassemble Power Feed 56

Disassembly of Short Bearing Blocks ------ 57

Disassembly of Long Bearing Blocks ------ 58

Cleaning & Lubricating Instructions --------- 59

Re-Assembly of Short Bearing Blocks ----- 59

Re-Assembly of Long Bearing Blocks ------ 60

GENERAL INFORMATION SECTION

Warranty Information ---------------------------- 63

POWER CABLE FEED SECTION

Tool Box and Accessory Kit -------------- 38-39

Pneumatic Tire Upgrade Kit ------------------ 40

Hoist Bracket Upgrade Kit -------------------- 40

Spartan Accessory Blades -------------------- 41

Page 4

Introduction

The Spartan Model 1065 Electric Drain/Sewer Cleaning Machine has been designed and

manufactured with high quality materials and care in workmanship. The instructions in this manual

have been prepared to ensure that, when followed, the Spartan Model 1065 will provide long and

efficient service.

WARNING: It is the responsibility of the operator to read and understand the

Operator’s Manual and other information provided and use the correct

operating procedure. Machines should be operated only by qualified

operators. Failure to do so can result in personal injury, death or machine

damage.

Read the entire manual before the initial start-up of the machine. It is important to know the correct

operating procedures of the machine and all safety precautions to prevent the possibility of

property damage and/or personal injury.

NOTE: Information in this manual is current at the time of printing. Spartan Tool reserves the right

to make changes and improvements to its products at any time without notice or obligation.

Service Information

All requests for information, service or parts should include machine serial number. Additional

copies of this Owner’s Manual can be downloaded free of charge from the Spartan Tool website,

www.spartantool.com.

For more information contact: Customer Service, Spartan Tool L.L.C.

1506 W. Division Street

Mendota, IL 61342-2234

Phone (800) 435-3866

Fax (888) 876-2371

Record below and retain product model and serial number.

Model Number:____________________

Serial Number: ____________________

Page 5

Specifications and Features

IMPORTANT

For your own safety

Before assembling and operating this unit, read this operator’s manual carefully and

completely. Learn the operation, applications and potential hazards peculiar to this unit.

Drum Capacity: 110’ of 3/4” innercore of sewer cable, or 160’ of .66 Magnum cable.

Cleaning Up to 250’ (recommended line size: 3” - 10” diameter)

Capacity:

Motor: Permanent magnet; 120 volt AC (rectified); 0.65 amps (DC) @ 3050 rpm (no load);

4.2 amps (DC) 200 oz-in torque @ 1800 rpm.

Weight: 147 lbs. for a 1065 Power Feed machine w/10’ anchor cable.

Height: 40” to top of handle.

Width: 24”

Length: 33” with Dial-A-Cable Power Feed.

Drum Speed: 220 RPM with no load.

Cable Feed: Spartan Dial-A-Cable Power Cable Feed.

Frame: Extra strength aluminum magnesium alloy.

• Heavy duty permanent magnet motor with reverse capability.

• Inner drum rotates independently of outer drum, virtually eliminates cable kinking, buckling

and controls torque buildup.

• Outer drum keeps dirt inside, off operator and work area.

• Air foot switch with cord assembly keeps both hands free for safe, easy operation.

• Compact, portable design.

• Extra-strength aluminum magnesium alloy construction.

• Integral continuous belt stair skids.

• Retractable “Sure-Grip” handle.

• Permanently attached power cord connection to assure electrical safety at the machine.

Page 6

Safety Instructions

Figure 1

Use of any electrical equipment in a wet or damp environment can cause fatal shock if not properly

guarded against by the operator.

1. Know Your Drain Cleaning Machine. Read this Operator’s Manual carefully. Learn the operation,

applications and limitations of this machine.

2. Grounding Instructions. Before using your Spartan equipment, make sure that a properly grounded,

(three hole) electrical outlet is available. If not, as in older homes, use a three-prong adapter and

connect the green pigtail or grounding lug to a known ground, such as a (metallic) cold water

pipe.

This tool should be grounded while in use to protect the operator from electric shock. The tool is

equipped with a three-conductor cored and proper grounding type receptacle. The green (or

green and yellow) conductor in the cord is the grounding wire. Never connect this wire to a live

terminal. Units designed for use on less than 150 volts, have a plug that looks like that shown in

Fig. 1A. An adapter, (Fig. 1B and 1C), is available for connecting three-prong plugs to two-prong

receptacles, (except in Canada). If such an adapter is used, the green colored rigid ear, lug, or

the like, extending from the adapter must be connected to a permanent ground such as a properly

grounded outlet box.

This machine is equipped with a Ground Fault Circuit Interrupter (GFCI), which should always be

plugged directly into an inspected, grounded receptacle. Plug the three-pronged plug on the

machine power cored with GFCI directly into an inspected grounded outlet and then test and

reset the GFCI.

Never cut off the grounding prong on the power cord for use in a two-hole outlet. Doing so cuts off

your protection from shock. Replace or repair all damaged power cords and components.

Page 7

Safety Instructions (cont.)

3. Extension Cords. DANGER- Improper use of an extension cord will cause death or severe injury.

The GFCI on the machine’s power cord does not protect the operator from electrical shock along

the extension cord.

If an extension cord must be used, it must be of an approved, three-wire construction, equipped

with a three-pronged plug, and in good condition. Replace or repair damaged cords.

Do not use an undersized extension cord. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. Use the following minimum gages depending upon

the length of the extension cord:

-16 Ga. –for cords of less than 100 feet in length

-14 Ga. –for cords of 100 feet to 150 feet in length.

If in doubt, use the next heavier gage. (The smaller the gage number, the heavier the cord.) When

the machine is used outdoors, use only extension cords intended for use outdoors and so marked.

Do not allow an extension cord to be exposed to water.

Don’t assume that all three hole outlets are properly installed. Check the outlet and also the adapter,

if used, with an outlet testing device which quickly indicates if a ground is connected. Correct a faulty

test indication before proceeding.

4. Don’t Abuse Cord. Never move or lift tool by cord or yank it to disconnect from receptacle. Keep

cord from heat, oil and sharp edges.

5. Disconnect Power Cord. When not in use, before servicing, and when changing accessories,

such as blades and cutters.

6. Guard Against Electric Shock. Prevent body contact with grounded surfaces such as pipes,

radiators, ranges, refrigerator enclosures.

7. Avoid Accidental Starting. Don’t move plugged-in tools. Make sure switch is in OFF position

before plugging in power cord.

8. Stay Alert. Watch what you are doing. Use common sense. Do not operate tool when you are

tired.

9. Keep Work Area Clean. Cluttered areas invite injuries.

10. Consider Work Area Environment. Don’t expose power tools to rain. Keep work area well lit.

Do not use tool in presence of flammable liquids or gases.

Avoid operating the machine in areas of standing water.

Page 8

Safety Instructions (cont.)

11. Dress properly. Do not wear loose clothing or jewelry. They can be caught in moving parts.

Wear protective hair covering to contain long hair.

Wear standard equipment. (Spartan riveted gloves). Never grasp a rotating cable with a cloth or

loose fitting glove which would get wrapped around cable. Replace gloves if rivets or staples

start to pull out.

Wear rubber boots and wear rubber gloves inside your Spartan cable handling gloves to further

insulate yourself.

12. Use Safety Glasses. Guard against foreign material that might fly off cable.

13. Don’t Overreach. Keep proper footing and balance at all times.

14. Keep Children Away. Do not let visitors contact tool or extension cord.

All visitors should be kept away from work area.

15. Use Recommended Equipment and Accessories.

Use of improper equipment may be hazardous.

Don’t force small cable with attachment to do the job of heavy-duty cable.

16. Don’t Force Tool.

It will do the job better and safer at the rate for which it was intended.

17. Remove Punches and Wrenches. Form a habit of checking to see that punches and adjusting

wrenches are removed from tool before turning it on.

18. Keep Guards in Place. Never operate machine with guard removed.

19. Avoid Operating Machine in Reverse. Operating machine in reverse can result in cable damage

and is used only to back tool away from an obstruction.

Warning! Continued drum rotation in reverse position will cause cable to “jump” out of drum. Possible

operator injury could result.

20. Do Not Over Torque Cables. Excessive and/or continued rotation of the drum once an obstruction

has been encountered will over torque the cable. Kinking or breakage of cable may result. A

worn cable can be identified as being very limber, kinked or as having flattened coils on the

outside of cable. Worn cable should be replaced as soon as possible.

Page 9

Safety Instructions (cont.)

21. Maintain Tools with Care. Keep tools sharp and clean for better and safer performance.

Follow instructions for lubricating and changing accessories.

Never use damaged power cords.

Inspect tool cords periodically and if damaged, repair with proper Spartan replacement parts.

Inspect extension cords periodically and replace if damaged.

Keep handles dry, clean, and free from oil and grease.

22. Check Damaged Parts. Before further use of the tool, a guard or other part that is damaged

should be carefully checked to determine that it will operate properly and perform its intended

function. Check for alignment of moving parts, binding of moving parts, breakage of parts,

mounting and any other conditions that may affect its operation. A guard or other part that is

damaged should be properly repaired or replaced.

Replace defective switches with proper Spartan replacement parts.

Do not use tool if switch does not turn on and off.

23. Store Idle Tools. When not in use, tools should be stored in a dry and locked up place, away from

children.

24. Handling Cables. Be very careful when cleaning drains exposed to cleaning compounds. Wear

protective gloves when handling cable, and avoid direct contact of skin and especially the eyes

and facial areas as serious burns can result from some drain cleaning compounds.

Page 10

Machine Features

1065 With Dial-A-Cable

Power Cable Feed

Figure 2

STUDY THESE INSTRUCTIONS CAREFULLY BEFORE YOU OPERATE YOUR EQUIPMENT

JOINING CABLES

All cables and leaders are coupled together by male and female couplings, and held securely by

means of expansion pins as illustrated.

The cable and coupling stand is furnished with the optional tool box to provide a support on which to

rest your cable when assembling or disassembling the couplings.

Assembly:

Place coupling in groove on top of stand with portion of expansion pin in upright position. Using

hammer, drive expansion pin down flush with coupling. Assembly is complete, cable and machine

are ready for use.

Assembly Instructions

Andere Handbücher für 1065

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Spartan Pfeifenreiniger Handbücher

Spartan

Spartan 81 Bedienungsanleitung

Beliebte Pfeifenreiniger Handbücher anderer Marken

Virax

Virax VAL 80 Bedienungsanleitung

Ribimex

Ribimex Ribitech PRFDP Betriebsanleitung

PICOTE

PICOTE MINI SMART HEAT MILLER Gebrauchs- und Pflegehandbuch

General Pipe Cleaners

General Pipe Cleaners Speedrooter 92 S92-450 Bedienungsanleitung

Parkside

Parkside 270382 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners JM-1450 Bedienungsanleitung

PICOTE

PICOTE Smart Spider DN150/6" Bedienungsanleitung

Dali

Dali GQ-75 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Gen-Eye SD Bedienungsanleitung

Kompernass

Kompernass 64586 Bedienungsanleitung

Inder

Inder Power P-30 Bedienerhandbuch

Gap Power

Gap Power Speedrooter 92R Bedienungsanleitung

Parkside

Parkside 102800 Betriebsanleitung

General Pipe Cleaners

General Pipe Cleaners Speedrooter XL Bedienungsanleitung

Wöhler

Wöhler DH 420 Bedienungsanleitung

Elliott

Elliott Roto-Jet II Series Handbuch

General Pipe Cleaners

General Pipe Cleaners JM-3055 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners JM-2900 Bedienungsanleitung