Speco O8VD3M Bedienungsanleitung
Quick Start Guide
O8VD3M
Welcome
Thank you for purchasing this network camera!
This owner's manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, contact Speco Technologies Tech Support at
1-800-645-5516
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply or adequate PoE switch.
Please note: The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
Do not expose the unit to heavy stress, violent vibration or long-term exposure to water
and humidity during transportation, storage, and/or installation.
Do not install near sources of heat.
Only install the product in environments inside the specification operating temperature
and humidity range.
Do not install the camera near power lines, radar equipment or other electromagnetic
radiation.
Do not block any ventilation openings if any.
Use all the weatherproofing hardware requirement to minimize weather intrusion.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on
the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth
Important Safeguards and Warning
Warning
Statement
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
.
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco
Technologies reserves the right to modify these without notice and without incurring
any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is
broken or missing in the package.
dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean
the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure
cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.
Dome cover is an optical device, please don't touch or wipe cover surface directly during
installation and use, please refer to the following methods if dirt is found:
Stained with dirt: Use oil-free soft brush or hair dryer to remove it gently.
Stained with grease or fingerprint: Use oil-free cotton cloth or paper soaked with alcohol
or detergent to wipe from the lens center outward. Change the cloth and wipe several
times if it is not clean enough.
Package
1
Overview
3 Overview
2
Camera Quick start guide CD
Drill template
Screwdriver
Junction box
CVBS&DC
IN cables
Rubber plug
1 Ethernet Connector
2 Audio Input (MIC)
3 Audio Output (HP)
4 CVBS Video Output
5 Alarm Input/Output
6 Power Connector
7 Zoom-
8 Zoom+
9 Micro SD Card Slot
10 Reset
11 DC IN & CVBS Interface
12 Microphone
1
3
4
5
6
2
ALARM
4321
12
10
7
8
9
11
4 Screws
(6.5×38mm)
4 screws
8 Plastic screw
anchors
4 Screws 4 Rubber o-rings
for screws
(PM 4×16mm)
(PA 4×25mm)
* It is recommended to install the water-proof connector for outdoor installations.
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through both
elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the water-proof connector. Then tighten the
nut and the main cover.
2
13
Water-proof connector
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
12VDC
ALARM
4 3 2 1
External microphone
Connecting Network Cable
Gap
Installation
3
* Before you start, please make sure that the wall or ceiling is strong enough
to withstand three times the weight of the camera.
① Attach the drill template of the junction box to the place where you
want to install the junction box and then rill the screw hole and calbe
hole on the wall according to the drill template.
② Install junction box onto the wall by using the screws provided.
Trim Ring
Lower Dome
12mm
6.5×38mm
4×
Rubber o-ring
③ Align the gap of the trim ring with the microphone by turning the
trim ring with fingers. Then remove the trim ring from the gap of the
camera.
Microphone
④ Connect the cables, mount the rubber plug to the gap of the
mounting base and install the camera onto the junction box.
Turn
Rubber Plug
⑤ Three-axis adjustment. Before adjustment, preview the image of the
camera on a monitor and then adjust the camera according to the figure below
to get an optimum angle.
Rotation 0°~345°
Tilt 0°~77°
Pan 0°~345°
PM 4×16mm
6mm
4×
Web Operation and Login
4
● Operation
IP Scanner can search for the device on the local network.
① Make sure that the camera and the PC are connected to the same
local network. The camera is set to DHCP by default.
② Install IP Scanner from the CD and run it after installation.
Or download from https://www.specotech.com/ip-scanner/
Install the lower dome back to the camera and fasten it with screws.
Put the trim ring onto the lower dome. Finally, remove the protection
film softly.
③ In the device list, you can view the IP address, model number, and
MAC address of each device. Select the applicable device and double
click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser.
The login interface is shown above. Default user name is admin and
password is 1234. After logging in, follow directions to install
applicable plugins if prompted.
O8VD3M
5C:F 2:07:24:68:9A
Inhaltsverzeichnis
Andere Speco Sicherheitskamera Handbücher
Speco
Speco CVC5100BPVF Bedienungsanleitung
Speco
Speco O8VT3M Bedienungsanleitung
Speco
Speco CVC-510C Bedienungsanleitung
Speco
Speco CVC-5815DNV Bedienungsanleitung
Speco
Speco CVC-607CMTP Bedienungsanleitung
Speco
Speco HT-INTD8 Bedienungsanleitung
Speco
Speco HTD8SCS Series Bedienungsanleitung
Speco
Speco HT-7815DNV Bedienungsanleitung
Speco
Speco CVC627MT Bedienungsanleitung
Speco
Speco LEDome Bedienungsanleitung
Speco
Speco O4FB1M Bedienungsanleitung
Speco
Speco O4VD2 Bedienungsanleitung
Speco
Speco CVCM6DC Bedienungsanleitung
Speco
Speco O2iD9 Bedienungsanleitung
Speco
Speco O4P4X Bedienungsanleitung
Speco
Speco VL-611C Bedienungsanleitung
Speco
Speco VLEDT2HG Bedienungsanleitung
Speco
Speco ProVideo CVC-724EXTP-2C Bedienungsanleitung
Speco
Speco O2D7M Bedienungsanleitung
Speco
Speco HT7040H Bedienungsanleitung
