Spectra Logic AIT-4 Handbuch
1
Spectra 20K and 64K Library AIT-4 Drive Upgrade
SPRT-1061-A-092004
The Sony AIT-4 drives double the Spectra 20K and 64K library capacity and transfer rate.
Review this document for information about AIT-4 and about upgrading your library to
take advantage of AIT-4 drive technology.
•Preparation, below
•Updating Firmware on page 2
•Replacing Drives on page 4
•Completing the Drive Upgrade Process on page 6
•Sony AIT Drive Specifications on page 6
Preparation
1. Identify the drives to be upgraded in your Spectra 20K/64K library.
2. Make sure you have an AIT-4 drive for every drive you are replacing, and a
library firmware upgrade diskette.
3. If you are going to return the drives to Spectra Logic (for example, for trade-ins
or pre-purchase), make sure to reserve the drive packaging for later use.
4. Download from the Sony Web site and install on the library’s host system a
driver for the host’s operating system.
5. Make sure all backup procedures are halted, and that you have fifteen minutes
available per drive to be upgraded, so that you can configure, install, and test.
Spectra 20K/64K Library AIT-4 Drive Upgrade
2
Updating Firmware
If you do not have firmware diskettes, access the library upgrade remotely from the
Spectra Logic site, as outlined in the library user guide or www.SpectraLogic.com.
1. Insert Disk 1 in the LCM disk drive (Figure 1).
2. Reset the LCM by cycling the power or pressing the reset button on back of
LCM.
3. Follow on-screen directions, inserting disks one at a time until operation is
complete.
4. Remove all disks and reset the LCM. The operating system and Library
Controller will now be upgraded.
5. The Library Controller alerts the user Configuration of QIP (X) Bus (X) Does
Not Match Front Panel for each logical library. Select OK. This message does
not appear after all QIPs have been upgraded.
6. Once you have the firmware files added to the local directory, go to Updating
Firmware Using the LC, next.
Figure 1 Insert Disk 1 in the LCM disk drive.
LCM Disk
Drive
Spectra 20K/64K Library AIT-4 Drive Upgrade
3
Updating Firmware Using the LC
1. On the Library Controller, select Toolbars, then select Maintenance. The
Maintenance toolbar displays.
2. Select Update F/W. The Firmware Update screen displays (Figure 1).
3. In File Locations, select Local Directory -> Select Location, then select the
most recent firmware package.
4. Select Update Firmware. The library firmware update process begins. A window
displays a message, asking you to wait.
Caution: Do not interrupt the library while firmware is downloading. The
firmware download takes less than 10 minutes.
Figure 1 Firmware Update screen.
Spectra 20K/64K Library AIT-4 Drive Upgrade
4
Replacing Drives
Moving Original Drives Off-line
1. On the Library Controller, select Toolbars -> General. The General toolbar
displays.
2. Select Drive Config. The Drive Configuration screen appears Figure 2.
3. Select the drive you want to replace, the select Replace. A dialog box series
displays, first asking whether it is Okay to Replace Drive? then “Are you sure
you want to open the door?
4. Select Okay for each. This powers down the drive and disengages the solenoid
latches on the front door. A dialog box displays the message Open Door and
Replace Drive. Close and Latch Door. Tap Okay when complete.
Note: Do not select OK until you have completed the procedure.
Figure 2 The Drive Configuration Screen.
Spectra 20K/64K Library AIT-4 Drive Upgrade
5
Removing Original Drives
1. Use the library door key to open the library door.
2. Pull the old drive out of the drive slot (Figure 3).
3. Slide the new drive firmly into the same slot while pressing it to the right against
the library wall. A red LED on the drive lights up.
4. Close the library door.
5. Secure the lock with the key.
6. Return to the Library Controller, then select OK. The library processes this
change, and may require a few minutes to complete. When the drive has been
configured, another statement displays: The library geometry has changed-
Reloading geometry, your drive information may be invalid. Tap OK.
7. Select OK.
8. Review the Drive Configuration screen. If the drive displays as offline, select
Config, then select OK. The drive now displays as online.
The library automatically configures the new drive with the old drive’s
configuration settings.
9. Repeat this procedure for every drive to be upgraded.
Figure 3 Pull the old drive out of the drive slot.
Spectra 20K/64K Library AIT-4 Drive Upgrade
6
Returning Old Drives
To return old drives to Spectra Logic (for example, if you are trading in the drives, or if
you pre-purchased the new drives), use the AIT-4 drive packaging and return the drives
to Spectra Logic (North America) or contact Support for assistance in determining how
to return the drives.
Completing the Drive Upgrade Process
1. Test your drives. For example, back up a set of data that includes one executable
program; restore the data to a temporary directory; then read the restored data
and run a restored program. Refer to your backup software documentation for a
more specific procedure. After you have performed a drive test successfully,
continue.
2. Restart backup processes
Sony AIT Drive and Media Specifications
Sony AIT Drive Specifications
The following table summarizes the specifications for Sony AIT media.
Tape Type Length Capacity a
a. All specifications subject to change without notice.
AIT-1 (SDX-25C) 170 meters 25 GB native (65 GB with ALDC)
AIT-1-XL (SDX-35C) 230 meters 35 GB native (91 GB with ALDC)
AIT-2 (SDX2-36C) 170 meters 36 GB native (94 GB with ALDC)
AIT-2 (SDX2-50C) 230 meters 50 GB native (130 GB with ALDC)
AIT-3 230 meters 100 GB native (260 GB with ALDC)
AIT-4 230 meters 200 GB native (520 GB with ALDC)
Spectra 20K/64K Library AIT-4 Drive Upgrade
7
Sony AIT Tape Drive Specifications
The following table summarizes the specifications for Sony AIT drives.
LED Information
The following table summarizes the information carried by the drive’s LEDs:
Parameter AIT-1 AIT-2 AIT-3 AIT-4
Ambient operating temperaturea
a. This applies to the drives; the limits for the library are given in the library user guide.
+41°F to +104°F (+5°C to +40°C)
Storage temperature -40°F to +158°F (-40°C to +70°C)
Operating humidity 20% to 80% non-condensing
MTBF 200,000 hours @
100% duty cycle
300,000 hours @
100% duty cycle
400,000 hours @
100% duty cycle
400,000 hours @
100% duty cycle
Average file access time < 55 seconds < 27 seconds < 27 seconds < 52 seconds
Uncorrectable error rate Less than 1 x 10-17 bits
Sustained transfer rateb, c
b. This is a per-drive value. Total sustained transfer rate for the library depends on the number of drives installed in the library.
c. The sustained transfer rate can increase by an average of 2.6 times with compression, dependent on the type of data.
3 MB/sec native 6 MB/sec native 12 MB/sec native 24 MB/sec native
Burst transfer rate
(synchronous maximum) d
d. The actual burst transfer rate is limited by the performance of the SCSI HBA, the controller, and the buffer control hardware.
40 MB/sec 40 MB/sec 160 MB/sec 160 MB/sec
Type of Blink
LED Type
Tape Motion Cleaning Request Replace Tape
Offa
a. Off: no color in the LED
No Tape Cleaning is not necessary No media error occurred
Onb
b. On: Blue and not blinking
Tape Loaded Cleaning request Media error occurred
Slow Flashc
c. Slow flash: flashes blue for 3-1/2 seconds and off for 1/2 second
Tape access in progress (read/
write)
Cleaning is not completed N/A
Fast Flashd
d. Fast flash: flashes blue for 1/4 second and off for 1/4 second
Tape access in progress (other) N/A N/A
All Flashe
e. All LEDs flashing: all flash blue for 1/4 second and off for 1 second
Hardware error occurred
Spectra 20K/64K Library AIT-4 Drive Upgrade
8
Andere Handbücher für AIT-4
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Spectra Logic Lagerung Handbücher
Spectra Logic
Spectra Logic Spectra 64K Bedienungsanleitung
Spectra Logic
Spectra Logic T-Series Spectra T120 Betriebsanleitung
Spectra Logic
Spectra Logic Spectra 12000 Bedienungsanleitung
Spectra Logic
Spectra Logic Spectra nTier500 Bedienungsanleitung
Spectra Logic
Spectra Logic AIT-3 Bedienungsanleitung
Spectra Logic
Spectra Logic Spectra 2k Merkblatt
Spectra Logic
Spectra Logic 2007 Bedienungsanleitung
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Spectra Logic
Spectra Logic T-Series Spectra T200 Bedienungsanleitung
Spectra Logic
Spectra Logic DAStape 100 Bedienungsanleitung
Spectra Logic
Spectra Logic Spectra T950V Bedienungsanleitung
Spectra Logic
Spectra Logic Spectra 10K Bedienungsanleitung
Spectra Logic
Spectra Logic Spectra 10000 Handbuch
Spectra Logic
Spectra Logic Spectra 12000 Bedienungsanleitung
Spectra Logic
Spectra Logic 10K Library Betriebsanleitung
Spectra Logic
Spectra Logic T-Series Spectra T50e Stücklistenhandbuch
Spectra Logic
Spectra Logic Spectra 12K Handbuch
Spectra Logic
Spectra Logic T-Series Spectra T200 Handbuch
Spectra Logic
Spectra Logic Spectra 64K Handbuch
Spectra Logic
Spectra Logic AIT-3 Handbuch
Beliebte Lagerung Handbücher anderer Marken
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung
Dell
Dell PowerVault MD3600f Series Bedienungsanleitung