SpectraLink NetLink 8020 Bedienungsanleitung

FIELD VERIFIED

Avaya Wireless AP-3, AP-4 Access Points

This document details the specifications for configuring the Avaya Wireless AP-3, AP-4

series access points (APs) with NetLink Wireless Telephones.

Product Summary

Manufacturer: Avaya

Approved product(s): Avaya Wireless AP-3, AP-4

RF technology: Direct-sequence spread spectrum (DS), 2.4 GHz

AP software version: Firmware version 2.5.5/3.1.0 †

NetLink handset models: e340/h340/i640 8000 Series

NetLink radio mode: 802.11b 802.11b

Maximum telephone calls per AP: 12 *

AP configuration parameters: See

Access Point Configuration

below

Indoor range (typical): See vendor specifications for AP

Required network topology: Switched Ethernet

Network constraints: Dedicated segment for wireless, single subnet

WEP capability: Yes *

ESSID auto-learn function: Yes *

† Earlier and later software versions have not been tested for the NetLink SVP Server compliance, except

as noted. Refer to

NetLink Wireless Telephone WLAN Compatibility List

for field-verified AP software

versions.

* Telephone calls per AP must be configured in the system per documentation provided by SpectraLink.

WEP and Automatic Learn are programmed into each handset in addition to being configured in the AP.

NetLink Wireless Telephones

NetLink Wireless Telephones use voice over IP technology on IEEE 802.11b-

compatible wireless local area networks (WLANs). Access points utilize radio

frequencies to transmit signals to and from the NetLink Wireless Telephones.

Access Point Capacity and Positioning

Each site is unique in its AP requirements. Please take the following points into account

when determining how many APs are needed and where they should be placed in the

facility.

Handset range

There must be wireless LAN coverage wherever NetLink Wireless Telephones will be

used. The typical range for a NetLink Wireless Telephone is comparable to that of a

laptop computer utilizing a wireless LAN PC card. However, NetLink Wireless

Telephones are likely to be used in areas where data devices are not typically used, such

PN: 72-9977-00-E.doc Page 1

FIELD VERIFIED

as stairwells and outdoor areas. NetLink Wireless Telephones have a Site Survey mode

that displays dBm levels to determine adequate WLAN coverage. Refer to the

NetLink

Wireless Telephone Configuration and Administration

document for details about this

feature.

Number of handsets per access point

Estimate the number of NetLink Wireless Telephones and their anticipated call volume

per AP area to ensure that the maximum number of calls per AP will not be exceeded. In

this estimate, consider the data rates at which the handsets will operate. Higher data rates

can only be sustained while well within the range of the AP. If the NetLink Wireless

Telephones will be operating near the limits of the RF coverage from the AP, they will

automatically drop to 1 Mb/s operation. NetLink Wireless Telephones require

approximately 15% of the available bandwidth per call for 1 Mb/s operation,

approximately 10% of the available bandwidth per call for 2 Mb/s operation,

approximately 7% of the available bandwidth per call for 5.5 Mb/s operation, and

approximately 5% of the available bandwidth per call for 11Mb/s operation.

Note: the maximum number of telephone calls per AP quoted in the summary table

above is based on 11 Mb/s operation, and will be reduced if some or all NetLink

Wireless Telephones are operating at 1, 2, or 5.5 Mb/s.

LAN bandwidth

Estimate anticipated peak call volume to ensure that the LAN has enough bandwidth

available to handle the network traffic generated by all of the wireless devices. Network

traffic can be monitored/analyzed using a network sniffer or a simple network

management protocol (SNMP) workstation.

Number of other wireless devices per AP

The NetLink Wireless Telephones share bandwidth with other wireless devices. To

ensure adequate RF bandwidth availability, consider the number of wireless data devices

in use per AP.

Notes on Configuration

The AP must support SpectraLink Voice Priority (SVP). Contact your AP

vendor if you need to upgrade the AP software.

If you encounter difficulties or have questions regarding the configuration process,

please contact the Customer Support Hotline at (800) 775-5330. The hotline is open

Monday through Friday, 6 a.m. to 6 p.m. Mountain time.

PN: 72-9977-00-E.doc Page 2

FIELD VERIFIED

Access Point Configuration

1. Connect to the AP via Netscape or Internet Explorer by navigating to the URL

http://<IP_Addr> (where <IP_Addr> is the IP address of the AP). Note: these

configuration steps can also be accomplished using the SNMP-based

Avaya/Orinoco ScanTool program.

2. From the main page, click the Configure link.

3. To configure WEP settings, obtain the key values from the local network

administrator and use the

Avaya AP-3, AP-4 User Guide

for guidance in

programming the encryption settings. The WEP configuration screen is reached

from the main menu by clicking Configure, followed by Security, followed by

Encryption.

Note that the NetLink Wireless Telephones must each be configured manually with

the identical WEP settings.

4. Click Configure, then click the Interfaces tab and choose the appropriate radio (Slot

Aor Slot B) to configure.

5. From the Interfaces tab confirm that the RTS/CTS Medium Reservation Threshold

is greater than 600 or disabled.

6. Set the Multicast Transmit Rate to 11Mb/s.

7. Next go to the Bridge tab, select SpectraLink VoIP to ensure that SpectraLink Voice

Priority (SVP) is enabled.

Conditional: If the AP’s software version is 2.5.xx or later, SVP must be activated

using the Avaya command line interface (CLI).

Connect to the access point via serial interface or Telnet.

8. To check to see if SVP is enabled:

Type show spectralink, then press Enter; it will display enabled or disabled.

To enable SVP:

Type set speclinkstatus enable, then press Enter.

Conditional: If you are not using a NetLink SVP Server and intend to use 802.11b/g

mode, you must also enter the command:

Type set speclinklegacysupport,then press Enter.

9. From the Bridge tab, select Advanced Filtering. Enable the Proxy ARP function and

disable IP/ARP Filtering.

10. From the Commands tab, restart the AP.

The AP is now ready for use with NetLink Wireless Telephones.

PN: 72-9977-00-E.doc Page 3

Andere Handbücher für NetLink 8020

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SpectraLink Schnurloses Telefon Handbücher

SpectraLink

SpectraLink 8400 Series Montageanleitung

SpectraLink

SpectraLink NetLink Wireless Telephones Best Practices White Paper Wireless... Kurzanleitung

SpectraLink

SpectraLink 8002 Kurzanleitung

SpectraLink

SpectraLink 84 Series Kurzanleitung

SpectraLink

SpectraLink K007 Bedienungsanleitung

SpectraLink

SpectraLink SpectraLink 1725-36122-001 Bedienungsanleitung

SpectraLink

SpectraLink NetLink 8020 Kurzanleitung

SpectraLink

SpectraLink NetLink i640 Bedienungsanleitung

SpectraLink

SpectraLink NetLink e340 Bedienungsanleitung

SpectraLink

SpectraLink 8400 Series Bedienungsanleitung

SpectraLink

SpectraLink NetLink 8000 Bedienungsanleitung

SpectraLink

SpectraLink Spectralink 7710 Bedienungsanleitung

SpectraLink

SpectraLink 7520 Bedienungsanleitung

SpectraLink

SpectraLink SpectraLink 1725-36097-001 Betriebsanleitung

SpectraLink

SpectraLink PIVOT 87-series Bedienungsanleitung

SpectraLink

SpectraLink Spectralink 7710 Bedienungsanleitung

SpectraLink

SpectraLink 8400 Series Montageanleitung

SpectraLink

SpectraLink 75-Series Bedienungsanleitung

SpectraLink

SpectraLink NetLink e340 Bedienungsanleitung

SpectraLink

SpectraLink NetLink e340 Service-Handbuch

SpectraLink

SpectraLink NetLink e340 Bedienungsanleitung

SpectraLink

SpectraLink NetLink 8000 Series Bedienungsanleitung

SpectraLink

SpectraLink Link Wireless Bedienungsanleitung

SpectraLink

SpectraLink JPI300 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung