SPL Transient Designer 4Mk2 Bedienungsanleitung

Manual

Further information: spl.audio

Transient Designer 4 Mk2

Level-independent dynamics processing

Transient Designer 4 Mk2

动态包络处理器（最新一代）

使用说明书

更多信息 : spl.audio

动态齿音消除器

Transient Designer 4 Mk2

Getting started

Read the security advises starting on page 7.

Make sure that the mains voltage of the Transient Designer 4 Mk2 mentioned in the

specifications (page 6) corresponds to the voltage of your region.

The power switch on the back of the Transient Designer 4 Mk2 must be in the off position.

(Off = O / On = I).

Connect the supplied power cord to the power connector of the Transient Designer 4 Mk2

and to a power outlet.

If the suppliedpower cord does not match your mainssocket outlet, please contact your dealer.

Thedevices thatareto be connected to the Transient Designer 4 Mk2 must be be switched

off.

Connect your devices to the inputs and outputs of the Transient Designer 4 Mk2 using

appropriateaudio cables (XLR).

Audio cables not included in the scope of delivery.

Power on

Switchonthe power switch on the rear panel of the Transient Designer 4 Mk2 (On = I).

The Power LED and all activated switches light up.

Power off

Switch off the power switch on the rear panel of the Transient Designer 4 Mk2 (Off = O).

The Power LED and all activated switches will no longer light up.

启动

请阅读第7页安全说明。

确保在规格中 (第06页)提到的 Transient Designer 4 Mk2 电源电压的选择与您所在地区

的电源电压一致。

Transient Designer 4 Mk2前面板上的电源开关必须处于关闭状态。 (关=O / 开=I )。

将提供的电源线连接到 Transient Designer 4 Mk2 的电源连接器和电源插座上。

如果提供的电源线与您的电源插座不匹配，请联系您的经销商。

连接到 Transient Designer 4 Mk2 的设备，必须是关闭的。

使用适当的音频电缆（XLR），将设备连接到 Transient Designer 4 Mk2 的输入和输出。

交付范围中不包括音频电缆。

开机

打开 Transient Designer 4 Mk2 后面板上的电源开关（开 = I）。

PWR LED 指示灯和所有激活的开关都会亮起。

关机

关闭 Transient Designer 4 Mk2 后面板上的电源开关(关= O).

PWR LED 指示灯和所有激活的开关将不会再亮起

Mains input

Power switch

Voltage selector

Fuse

PWR LED

Transient Designer 4 Mk2

Output

Input

Mains Input 主输入 Power switch 电源开关 Input 输入 Output 输出

Fuse 保险 Voltage selector 电压选择 PWR LED 电源指示灯

Transient Designer 4 Mk2

Attack

Attackcan be used to increase or attenuate the transient phase of a

signal by up to 15 dB. A positive attack value increases the amplitude of

the transient response.negative attack values lead to an attenuation.

Sustain

Sustain can be used to increase or attenuate the sustain phase of a

signal by up to 24 dB. Positive sustain values extend the sustain.

Negative Sustain values shorten the sustain.

Channels 1 & 2 as well as 3 & 4 can be linked for processing stereo signals.

Therespective left channel becomes the master.

Link

Attack（音量上升时间）

Attack 可以用来增加或减弱信号的瞬时相位，最高可达15dB。

正的Attack值会增加瞬态响应的振幅。负的Attack值会降低。

Sustain （延持）

Sustain延持可以用来增加或减弱信号的延音过程，

最高可达24dB。Sustain正值可以延长Sustain，

负值会缩短Sustain。

Link

立体声处理信号连接通道1和2以及3和4。各自的左通道成为

主通道。

TheOnswitchactivates the respective Transient Designer channel. This

allows you to quickly switch between processed and unprocessed signal.

To minimize switching noises,switching is performed directly after the

balanced inputs and outputs. This relay hard bypass circuitry also provides

immediate redirection of inputs to outputs in the event of a power fault on

the primary or secondary side of the power supply, or if the device is powered

off.

LED

The Sig LED (Sig) indicates whether an audio signal is

present at the input which has a level higher

than -20 dB.

Transient Designer 4 Mk2

开启 On 开关，激活相应的 Transient Designer 通道。可以在处理过和

未经处理的信号之间快速切换。

为了尽量减少切换时的噪音，在平衡输入和输出之后可进行直接切换。

在主电源发生故障时，或在设备断电的情况下，这种继电器环绕声电

路还能立即将输入转为输出。

LED

Sig LED (Sig) 指示是否有音频信号出现在输入端，且电平

高于-20dB。

Inhaltsverzeichnis

Sprachen:

Andere SPL Aufnahmegeräte Handbücher

SPL

SPL De-Esser 500 Series Bedienungsanleitung

SPL

SPL 2380 Bedienungsanleitung

SPL

SPL DeEsser Mk2 Bedienungsanleitung

SPL

SPL Vitalizer stereo MK2-T Bedienungsanleitung

SPL

SPL Kultube 2049 Bedienungsanleitung

SPL

SPL Madison 1260 Bedienungsanleitung

SPL

SPL 2Control 2860 Bedienungsanleitung

SPL

SPL 1211 Bedienungsanleitung

SPL

SPL Crimson 3 Bedienungsanleitung

SPL

SPL TwinTube 2920 Bedienungsanleitung

SPL

SPL Attacker2980 Bedienungsanleitung

SPL

SPL Atmos Bedienungsanleitung

SPL

SPL Vitalizer stereo MK2-T Bedienungsanleitung

SPL

SPL MMC1 Bedienungsanleitung

SPL

SPL Phonitor 2730 Bedienungsanleitung

SPL

SPL Frontliner 2800 Bedienungsanleitung

SPL

SPL Madicon Bedienungsanleitung

SPL

SPL Phonitor 2 1530 Bedienungsanleitung

SPL

SPL Crossover Bedienungsanleitung

SPL

SPL MasterBay Series Bedienungsanleitung

SPL

SPL Marc One Bedienungsanleitung

SPL

SPL Transient Designer 2715 Bedienungsanleitung

SPL

SPL Transient Designer 2880 Bedienungsanleitung

SPL

SPL Stereo Vitalizer Jack 9530 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch