Splendide AWD 129 Einrichtungshandbuch

Pages:

1 - 18

The information included in this Splendide RepairManual may change without notice. Please see our web site

www.splendide.com/service/docs.html for updates, corrections or additions.

PRODUCT: WASHER / WASHER-DRYER COMBO

MODEL: AW 120 / AW 122 / AW 125

AWD 120 / AWD 121 / AWD 129

6SOHQGLGH¥

5&$)/*$"-&%6$"5*0/

(306113&4&/54

53"*/*/((6*%&

REPAIR MANUAL

Page: i

This Repair Manual is intended for persons having electrical and mechanical training and a level of knowledge

of these subjects generally considered acceptable in the Appliance Service Industry. Splendide cannot be

responsible, nor assumes any liability for injury or damages of any kind arising from the use or misuse of

the information contained in this Repair Manual.

If you have any questions regarding the proper diagnosis, repair or operation of any Splendide Appliance, please

contact Splendide Division Westland Sales at 1-800-356-0766.

SERVICING SAFEGAURDS:

To avoid personal injury and/or property damage, it is important that safe servicing practices be observed at all times. Examples of

safe service practices are listed below but are not limited to the following:

1) Never attempt a product repair if you have any doubts as to your ability to complete the repair in a safe and

satisfactory manner.

2) Before servicing or removing an appliance:

- Disconnect power to the appliance.

- Turn off the gas / LP supply.

- Turn off the water supply.

3) Never interfere with the proper operation of any safety device.

4) Use only genuine factory replacement parts as substitutions may interfere with compliances to home safety codes or standards.

5) It is extremely important that all safety ground connections be reestablished prior to the completion of the service call. Failure to

do so will result in a hazardous condition being created.

6) Prior to returning the appliance back into active service, ensure the following:

- All electrical connections are correct and secure.

- Electrical leads are properly dressed and secured away from sharp edges, high temperature components and moving parts.

- All non-insulated electrical terminals, connectors, heaters, etc. are adequately spaced away from metal parts or panels.

- All safety grounds (both internal and external) are correctly and securely connected.

- All access panels are properly and securely reassembled.

SAFE SERVICE PRACTICES

AW 120 / AW 122 / AW 125

AWD 120 / AWD 121 / AWD 129

REPAIR MANUAL

Page: ii

Page

1. Model & Serial Number Locations.................................................................................................. 1

2. Top Panel....................................................................................................................................... 2

3. Control Panel..................................................................................................................................3

4. Control Panel Components............................................................................................................. 4

5. Toe Kick & Drain Motor .................................................................................................................. 6

6. Drum Boot...................................................................................................................................... 7

7. Door Switch.................................................................................................................................... 8

8. Water Valves..................................................................................................................................8

9. Heater Assembly (AWD 120 Only).......................................................................................................... 9

10. Pressure Switch............................................................................................................................ 10

11. Rear Access Panel....................................................................................................................... 10

12. Control Board............................................................................................................................... 11

13. Main Motor.................................................................................................................................... 12

14. Fault Codes.................................................................................................................................. 13

15. Schematics................................................................................................................................... 14

TABLE OF CONTENTS

AW 120 / AW 122 / AW 125

AWD 120 / AWD 121 / AWD 129

REPAIR MANUAL

Page: 1

1. MODEL & SERIAL NUMBER LOCATION

Fig. 1-3

• Model and Serial Number Tag located on the rear of the Appliance (Fig. 1-3).

• The Model and Serial Number Tag is located on the front of the Appliance behind the door (Fig. 1-1). The Model shown is an

AWD120 with a Serial Number of 403043152 (Fig. 1-2).

Note: Numbers located to the right of the nine (9) digit Serial Number are not required on the Warranty Claim Form.

Fig. 1-1 Fig. 1-2

AW 120 / AW 122 / AW 125

AWD 120 / AWD 121 / AWD 129

REPAIR MANUAL

Page: 2

2. TOP PANEL

Fig. 2-4

• To remove the Top Panel, first remove the two (2) Phillips screws located at the rear corners of the panel (Fig. 2-1). With the two

screws removed lift the rear of the panel up approximately three (3) inches and then slide the panel back, moving it away from the

Control Panel (Fig. 2-2)

Fig. 2-2

Fig. 2-1

Fig. 2-3

• With the Top Panel removed you can see the four (4) alignment slots on top of the Control Panel (Fig. 2-3) that correspond to the

four (4) alignment tabs on the bottom of the Top Panel (Fig. 2-4). When re-installing the panel make sure to align the tabs and

slots and then slide the panel back into place.

AW 120 / AW 122 / AW 125

AWD 120 / AWD 121 / AWD 129

REPAIR MANUAL

Page: 3

3. CONTROL PANEL

• To remove the Control Panel, first remove the two Phillips screws located on the top corners of the Control Panel (Fig 3-1).

Fig. 3-1

• Next, remove the wiring from each Switch and the Program Selector. To remove the Switch wiring simply press the Locking Tab

forward and slide the Wiring Connector up and out (Fig. 3-5). Now release the two (2) remaining Control Panel Locking Tabs

located on the bottom rear of the Control Panel (Fig. 3-6) and the complete Control Panel Assembly can be removed.

Fig. 3-5 Fig. 3-6

Fig. 3-2 Fig. 3-4

Fig. 3-3

• Next, remove the Soap Dispenser by grasping it firmly and sliding it out from its housing (Fig. 3-2). Now, remove the Dispenser

Door and Program Guide by lifting out the Hinge Pin (Fig. 3-3) the pin will easily slide up and out. With the Soap Dispenser and

Door completely removed you can remove the two (2) remaining Phillips Screws.

TECH NOTE: When re-installing the Control Panel make sure the bottom edge of the Soap Dispenser Housing rests on top of the

Control Panel opening as shown in the box of Fig. 3-4.

AW 120 / AW 122 / AW 125

AWD 120 / AWD 121 / AWD 129

• The Control Panel has three main controls; Push Buttons (A), Knobs (B) and the Program Dial (C).

− To remove a Push Button (A), first mask the area to protect against damaging the Control Panel, then carefully insert a small

screwdriver between the bottom of the Button and the Control Panel (Fig. 4-2), now pry the Button out and off.

− To remove the Knobs (B) or the Program Dial (C), grasp the firmly and pull straight out toward you.

Fig. 4-2

REPAIR MANUAL

Page: 4

4. CONTROL PANEL COMPONENTS - Switches and Potentiometers

Fig. 4-1

B C

• To remove either the Switches (A) or the Potentiometers

(B), first remove the Button and/or Knob. The Switch and

Potentiometers are held in place by four (4) positioning tabs

(Fig. 4-3). Using a small screwdriver press the tabs inward

then slide the Switch or Potentiometer out from the rear of

the Control Panel.

• On both Fig. 4-4 Switch and Fig. 4-5 Potentiometer you can

see the positioning tabs.

TECH NOTE: The tabs on the Switches and Potentiometers

are very delicate and can easily snap off.

Use care when removing or replacing.

Fig. 4-3

Fig. 4-4 Fig. 4-5

AW 120 / AW 122 / AW 125

AWD 120 / AWD 121 / AWD 129

REPAIR MANUAL

Page: 5

4. CONTROL PANEL COMPONENTS - Program Selector

• To remove the Program Selector, first remove the Program Selector Knob by grasping it firmly and pulling it toward you (Fig. 4-6).

With the Knob removed loosen the Phillips Screw and remove the Program Knob Bezel (Fig. 4-7). Now rotate the Program Dial

until the half moon cut out lines up with the Program Selector Locking Tab (Fig 4-8).

Fig. 4-6 Fig. 4-7 Fig. 4-8

• Using a small screwdriver push in on the Locking Tab (Fig. 4-9), while holding the Locking Tab in use your other hand to bring the

bottom of the Program Selector slightly away from the Mounting Plate, and then remove by sliding it up and off (Fig 4-10). In Fig.

4-11 you can see the four (4) alignment tabs that hold the Program Selector to the Program Selector Mounting Plate.

TECH NOTE: The Program Selector Mounting Plate does not have to be removed in order to remove the Program Selector.

TECH TIP: The Program Knob Bezel, Program Dial and Program Knob are all keyed to make re-installation easier.

Fig. 4-9 Fig. 4-10 Fig. 4-11

AW 120 / AW 122 / AW 125

AWD 120 / AWD 121 / AWD 129

REPAIR MANUAL

Page: 6

5. TOE KICK & DRAIN MOTOR

• To remove the Toe Kick, carefully insert a small screwdriver into each of the three (3) retention clips pushing each clip down and

then moving to the next clip (Fig. 5-1). With the retention clips released the Toe Kick will unsnap from the base (Fig. 5-2).

Fig. 5-1 Fig. 5-2

• The Drain Motor is held in place with two (2) Phillips screws and a twist lock

fitting (Fig. 5-3). Remove the two (2) Phillips screws, but leave the drain motor

in place until you remove the Bottom Pan in Fig. 5-5.

• With the Toe Kick removed you also have

access to the Drain Clean-out (Fig. 5-4).

Fig. 5-3 Fig. 5-4

• With the two Drain Motor screws removed, carefully lay the Washer on its back and remove the four (4) Phillips screws that hold

the Bottom Pan to the frame. With the Bottom Pan removed twist the Drain Motor Clockwise to release it from its mounting. To

remove the Drain Motor remove the three (3) hose connections and wiring.

TECH TIP: The Drain Hose can be replaced through the Rear Access Panel without removing the Drain Motor, see Section 11.

Fig. 5-5 Fig. 5-6

AW 120 / AW 122 / AW 125

AWD 120 / AWD 121 / AWD 129

REPAIR MANUAL

Page: 7

6. DRUM BOOT

Fig. 5-5

• To remove the Drum Boot (Fig. 6-1) start by removing the Door Boot Spring (Fig. 6-2). The Door Boot Spring is located just under

the front lip of the Drum Boot. Using a small screwdriver, slide the screwdriver under the spring and carefully remove it from around

the seal. With the Door Boot Spring removed, unseat the Door Boot from the washer door opening (Fig. 6-3). As you remove the

Door Boot from the door opening note how the seal will be reseated on the door opening when replaced.

TECH NOTE: When reinstalling the Door Boot make sure that the Boot Tab is located at the11:00 O'clock position (Fig. 6-1).

Fig. 6-1 Fig. 6-2 Fig. 6-3

Fig. 6-5Fig. 6-4 Fig. 6-6

• With the Door Boot unseated from the door opening remove the Top Panel as described in Section 2. For easier access to the

Door Boot Clamp Bolt (Fig. 6-5) remove the Soap Dispenser Housing (Fig. 6-4) as described in Sections 3 and 8. Loosen the Door

Boot Clamp Bolt using an 8mm Nut Driver (Fig. 6-6), but do not loosen completely. With the Door Boot Clamp loose you can now

remove the Door Boot.

TECH TIP: When installing the new Door Boot leave the Boot Clamp loosely fit until you seat the Boot to the Outer Drum, then

tighten the Boot Clamp Bolt. Also make sure to water test the unit before replacing the Top Panel to ensure maximum

visibility for possible leaks.

AW 120 / AW 122 / AW 125

AWD 120 / AWD 121 / AWD 129

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Splendide Waschmaschine Trockner Handbücher

Splendide

Splendide WD2100XC Bedienungsanleitung

Splendide

Splendide WDC7100XCP Bedienungsanleitung

Splendide

Splendide WD2100XCP Bedienungsanleitung

Splendide

Splendide WDV2200XCD Bedienungsanleitung

Splendide

Splendide Comb-o-matic 5200 Bedienungsanleitung

Splendide

Splendide 2000S Bedienungsanleitung

Splendide

Splendide WD2000S Bedienungsanleitung

Splendide

Splendide WDC1024M Bedienungsanleitung

Splendide

Splendide WD2000S Bedienungsanleitung

Splendide

Splendide WDC5200 Bedienungsanleitung

Splendide

Splendide WDC7100XC Benutzerhandbuch

Splendide

Splendide WD2100 Bedienungsanleitung

Splendide

Splendide WDC7100XC Benutzerhandbuch

Splendide

Splendide WDC1025MCEE Bedienungsanleitung

Splendide

Splendide WDC7200XCD Bedienungsanleitung

Splendide

Splendide WDC1024M Bedienungsanleitung

Splendide

Splendide WD2000S Einrichtungshandbuch

Splendide

Splendide WD802M Bedienungsanleitung

Splendide

Splendide WD802M Einrichtungshandbuch

Splendide

Splendide WDC1025MCEE Bedienungsanleitung

Splendide

Splendide Comb-o-matic 6200 Bedienungsanleitung

Splendide

Splendide WD2000S Bedienungsanleitung

Splendide

Splendide 7100XC Bedienungsanleitung

Splendide

Splendide Ariston AS66VX Bedienungsanleitung

Beliebte Waschmaschine Trockner Handbücher anderer Marken

Whirlpool

Whirlpool WFC8090GX Bedienungsanleitung

Whirlpool

Whirlpool LTE5243DQ6 Bedienungsanleitung

Bosch

Bosch XQG100-WDU285H00W Bedienungsanleitung

montpellier

montpellier MWD7512S Bedienungsanleitung

LG FHD0905 T Series Bedienungsanleitung

Midea

Midea MF200D85B Bedienungsanleitung

Maytag

Maytag MGT3800XW Bedienungsanleitung

Siemens

Siemens WD15G440TR Technisches Datenblatt

Equator

Equator Clothes Processor EZ1500 Bedienungsanleitung

John Lewis

John Lewis JLWD 1408 Bedienungsanleitung

Ariston

Ariston A1200WD Bedienungsanleitung

Whirlpool

Whirlpool YLTE5243DQ5 Bedienungsanleitung

Whirlpool

Whirlpool WFCR 75230 Installationsanleitung

ATT

ATT Hammer Jet v1 Bedienungsanleitung

AEG

AEG LAVAMAT 63742 VI Bedienungsanleitung

Electrolux

Electrolux EWW8024P5WB Bedienungsanleitung

GE GTD42EASJWH Bedienungsanleitung

LG F2721HVRB Bedienungsanleitung