Spraying Systems AutoJet 1000+ Bedienungsanleitung

Scan the QR code, or visit spray.com/autojetspraycontrol, to access

manuals, videos and additional resources on the AutoJet®1000+ control panel.

AUTOJET®1000+ SPRAY CONTROL PANEL

QUICK START GUIDE

POSITION AND MOUNT

THE PANEL

Find a suitable location to mount the spray control panel.

The system should be located within a reasonable distance

to an easily accessible and properly grounded power outlet

(power cord length is approximately 6 ft.). The panel should

be as close to the nozzles as possible.

Use good mounting practices. It should be mounted using

suitable hardware (5/16 in. or 8mm screws) in a place where

the enclosure will not be subjected to direct spray or mist

from the nozzles. It should be mounted horizontally with the

door always closed.

5.75"

(146.05 mm)

Ø.32"

(Ø8.13 mm)

4-places

9.25"

(234.95 mm)

.00"

(254 mm)

FLOAT 1

FLOAT 2

TRIG 1

INPUT

100-240V

50/60Hz 3A

OUT 1

TRIG 2

OUT 2

1000+

SPRAY CONTROL PANEL

CONNECT ELECTRICAL

SPRAY NOZZLE CABLES

Connect the electrical spray nozzles to out 1 (channel 1) or

out 2 (channel 2) connections on the control panel.

If you have a junction block in your order then wire the

nozzles to that first then the cable from the junction block

goes to the out 1 or 2 connection.

Junction Block

FLOAT 1

FLOAT 2

TRIG 1

INPUT

100-240V

50/60Hz 3A

OUT 1

TRIG 2

OUT 2

1000+

SPRAY CONTROL PANEL

3. CONNECT TRIGGER

OR SENSOR CABLES

Connect your trigger or sensor devices to the TRIG 1

and TRIG 2 connections. Available trigger devices are:

• Trigger cable (for use with customer supplied trig-

ger like a relay or PLC output)

• Electronic sensor (type is based on what was

selected for customer’s order)

- Standard photo eye sensor

- Proximity sensor

- Laser sensor, close or far distance

- Thru-beam sensor

• Handheld trigger

• Foot switch

FLOAT 1

FLOAT 2

TRIG 1

INPUT

100-240V

50/60Hz 3A

OUT 1

TRIG 2

OUT 2

1000+

SPRAY CONTROL PANEL

CONNECT FLOAT SWITCH

INPUT CABLES

The 1000+ has a digital input for a float switch, one per

channel (2 total). Cables go to the Float 1 and/or Float 2

connections on the control panel. When tank goes low,

there is a message shown on HMI and green system

status LED will flash.

FLOAT 1

FLOAT 2

TRIG 1

INPUT

100-240V

50/60Hz 3A

OUT 1

TRIG 2

OUT 2

1000+

SPRAY CONTROL PANEL

North Avenue and Schmale Road, P.O. Box 7900, Wheaton, IL 60187-7901 USA

spray.com | 1.800.95.SPRAY | Intl. Tel: 1.630.665.5000 ©Spraying Systems Co. 2021

1000+

SPRAY CONTROL PANEL

Recipe #

Recipe name

Start delay (s)

Stop delay (s)

RECIPE CONFIGURATION

Timing Mode:

Screen Capture to .jpg

CORN

0.20

0.25

Variable Spray

FLOAT 1

FLOAT 2

TRIG 1

INPUT

100-240V

50/60Hz 3A

OUT 1

TRIG 2

OUT 2

1000+

SPRAY CONTROL PANEL

POWER UP

THE PANEL

Plug panel into a fused (15A) grounded electrical socket

and turn on by depressing the power switch. The HMI will

illuminate, and the system is ready to operate.

SET RECIPE

CONFIGURATION

Set recipes and timing modes for each channel

and you are ready to spray. For more information on

Recipes and Timing Modes see Owner’s Manual.

Andere Handbücher für AutoJet 1000+

Andere Spraying Systems Bedienfeld Handbücher

Spraying Systems

Spraying Systems AutoJet 2850+ Bedienungsanleitung

Spraying Systems

Spraying Systems AUTOJET 1750+ Bedienungsanleitung

Spraying Systems

Spraying Systems AutoJet 1000+ Bedienungsanleitung

Spraying Systems

Spraying Systems AutoJet 2150+ Bedienungsanleitung

Spraying Systems

Spraying Systems AutoJet 1000+ Bedienungsanleitung

Spraying Systems

Spraying Systems AUTOJET 1750+ Bedienungsanleitung

Spraying Systems

Spraying Systems AutoJet 1750+ Bedienungsanleitung

Spraying Systems

Spraying Systems AutoJet 1000+ Bedienungsanleitung

Spraying Systems

Spraying Systems AUTOJET 1550+ Bedienungsanleitung

Spraying Systems

Spraying Systems AutoJet 2150+ Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten

Truma

Truma CP plus Bedienungsanleitung