SSV Works US-CMP65 Bedienungsanleitung
US-CMP65
Universal Cage Mount
6.5” Speaker Enclosures
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in
material or workmanship. All SSV Works Electronics are covered by a limited 1 year
warranty against defects in material or workmanship. Labor for replacement of defective
components is not covered. All SSV Works Speakers are covered by a limited 1 year
warranty against defects in material or workmanship. Contact SSV Works for further
warranty information.
1. US-CMP65 Enclosures (1 pair)
2. M6 x 1.0 Screws x 4
3. M6 Washers x 4
4. Mounting Disc x 2
5. 1/2” Allen Screw x 4
TOOLS NEEDED FOR INSTALLATION PARTS LIST
PARTS LIST IMAGES
6. Clamp Base x2
7. Mounting Clamp x 2
8. 1 - 3/4” Allen Socket
Head x 2
9. 5/16” Nut x 2
2. M6 x 1.0 Screws x 4
1. US-CMP65 Enclosures
(1 pair)
6. Clamp Base x2 7. Mounting Clamp x 2 8. 1 - 3/4” Allen Socket
Head and Washer x 2
6. 5/16” Nut x 2
5. 1/2” Allen Screw x 43. M6 Washers x 4 4. Mounting Disc x 2
- Wire Crimpers
- Wire Strippers
- 4mm and 5mm Allen
Wrench
- Drill with 1/4” Drill bit
- #3 Phillips Screwdriver
- Scribe or Marker
INSTALLATION NOTES
The use of a thread locker is recommended on all screws to prevent loosening due to vibration. It is recommended to wrap the bag that the clamps
come in around the cage before you slide the clamp onto the cage, this will prevent scratching.
C. At the top of the cage pod, behind the clamp base drill a ¼”
hole in the enclosure for your speaker wire to run out of, seal
this hole with silicone sealer
D. Place the speaker into the enclosure and mark the 4 mounting
holes with a scribe or marker, Pre-drill the marked mounting
locations using a 1/8” drill bit
B. Loosely install the clamp base to the cage mount pod with the M6 screws using
the #3 screwdriver, place the cage mount pod in the desired mounting location on
the vehicle, once the clamp base is in the desired position, tighten the 2 screws
US-CMP65
CD
B B
A. Attach the clamp base to the round mounting disc with the ½”
Allen screws
A
D. Connect and install the speaker into the enclosure (be sure to connect the “+”
speaker wire to the “+” terminal on the speaker and the “-“ speaker wire to the “-“
terminal on the speaker) using the #2 Phillips screwdriver
E E
G. Route the speaker wire away from any moving parts and any
sharp metal, then connect to the amplier
F. Place the mounting clamp on the cage using the plastic bag to prevent scratching, place the cage mount pod in its nal
mounting location and secure to the clamp with the Allen bolt and Nut
US-CMP65
G
WIRING INSTRUCTIONS
For proper sound, ensure the speaker polarity is correct connect the “+” to the “+” and the “-“to the “-“from the speaker wire to the amplier. If using with
an SSV Works complete system refer to the amplier wiring instructions for more detailed wiring information.
“+” “+”
“
-
”“
-
”
Amplier
© 2017 SSV Works, Oxnard, CA 93030 US-CMP65 Rev. B 4-11-17
F F F
Inhaltsverzeichnis
Andere SSV Works Rack & Stand Handbücher
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
