ST STDES-65ACFADP Technisches Datenblatt
Introduction
This document reports the functional, thermal, EMI, and efficiency measurements results for the STDES-65ACFADP 65 W
active clamp flyback adaptor reference design for USB Type-C™ PD source applications. This reference design meets CoC Tier
2 and DoE Level 6 efficiency requirements with a peak efficiency of 93.7% at full load.
The STDES-65ACFADP adopts the planar transformer technology, with an integrated GaN-based solution and digital control.
The reference design main devices are:
•ST-ONE: a programmable digital controller for the active clamp flyback primary high-low side GaN HEMT control plus a
secondary synchronous rectifier MOSFET control and USB-PD control;
•MASTERGAN2: a high-voltage enhancement mode GaN with a half-bridge configuration and integrated gate driver.
The STDES-65ACFADP is a fully assembled reference design developed for performance evaluation only, not available for sale.
STDES-65ACFADP test report
TN1402
Technical note
TN1402 - Rev 2 - November 2022
For further information contact your local STMicroelectronics sales office.
www.st.com
1Overview
The STDES-65ACFADP main features are:
• Universal input mains range: 90 Vac to 264 Vac - frequency 47 Hz to 63 Hz
• Output voltage range: 5 VDC - 20 VDC
• PD output:
– Five fixed PDOs: 5 V@3 A, 9 V@3 A, 12 V@3 A, 15 V@3 A, 20 [email protected] A
• Output power: 20 V - 3.25 A, 65 W max.
• Form factor: 54 mm (L)*31 mm (W)*25 mm (H)
• Efficiency: meets CoC Tier 2 and DoE Level 6 efficiency requirements, with a peak efficiency of 93.7% at
230 Vac 65 W
• Digital control for ACF primary and secondary sides
• Integrated GaN IC MASTERGAN2
• Compact, simplified PCB layout, and bill of material reduction
• EMC compliant: CISPR32B/EN55032B
• Planar transformer technology to achieve high-power density
Figure 1. STDES-65ACFADP architecture block diagram
Figure 2. STDES-65ACFADP reference design - top side
TN1402
Overview
TN1402 - Rev 2 page 2/35
Figure 3. STDES-65ACFADP reference design - bottom side
Fully assembled board developed for
performance evaluation only,
not available for sale
TN1402
Overview
TN1402 - Rev 2 page 3/35
2Specifications
Table 1. STDES-65ACFADP electrical specifications
Symbol Parameter Test conditions Minimum Nominal Maximum Unit
Input parameters
VIN Input line voltage 90 115/230 264 Vrms
fLINE Input line frequency 47 50/60 63 Hz
PSTBY No load input power (5 VOUT)
VIN = 115 VRMS, IOUT = 0 A
VIN = 230 VRMS, IOUT = 0 A
50
80 mW
PSTBY No load input power (9 VOUT)
VIN = 115 VRMS, IOUT = 0 A
VIN = 230 VRMS, IOUT = 0 A
170
180 mW
PSTBY
No load input power (12
VOUT)
VIN = 115 VRMS, IOUT = 0 A
VIN = 230 VRMS, IOUT = 0 A
220
260 mW
PSTBY
No load input power (15
VOUT)
VIN = 115 VRMS, IOUT = 0 A
VIN = 230 VRMS, IOUT = 0 A
280
290 mW
PSTBY
No load input power (20
VOUT)
VIN = 115 VRMS, IOUT = 0 A
VIN = 230 VRMS, IOUT = 0 A
180
220 mW
Output parameters - 5 V setting
VOUT Output voltage
VIN = 90 VRMS~264 VRMS
IOUT = 0 A~3 A 5 V
Vripple Output voltage ripple Peak-to-peak value with 20 MHz
bandwidth 180 250 mV
IOUT Output current 0 3 A
POUT Continuous output power 0 15 W
ηave
Four-point average efficiency
25%, 50%, 75%, and 100%
load
At 115 VAC and measured at the on-board
USB Type-C™ receptacle 90.2 %
ηave
Four-point average efficiency
25%, 50%, 75%, and 100%
load
At 230 VAC and measured at the on-board
USB Type-C™ receptacle 88.4 %
Output parameters - 9 V setting
VOUT Output voltage
VIN = 90 VRMS~264 VRMS
IOUT = 0 A~3 A 9 V
Vripple Output voltage ripple Peak-to-peak value with 20 MHz
bandwidth 152 250 mV
IOUT Output current 0 3 A
POUT Continuous output power 0 27 W
ηave
Four-point average efficiency
25%, 50%, 75%, and 100%
load
At 115 VAC and measured at the on-board
USB Type-C™ receptacle 91.2 %
ηave
Four-point average efficiency
25%, 50%, 75%, and 100%
load
At 230 VAC and measured at the on-board
USB Type-C™ receptacle 90.3 %
Output parameters - 12 V setting
VOUT Output voltage VIN = 90 VRMS~264 VRMS 12 V
TN1402
Specifications
TN1402 - Rev 2 page 4/35
Symbol Parameter Test conditions Minimum Nominal Maximum Unit
IOUT = 0 A~3 A
Vripple Output voltage ripple Peak-to-peak value with 20 MHz
bandwidth 180 250 mV
IOUT Output current 0 3 A
POUT Continuous output power 0 36 W
ηave
Four-point average efficiency
25%, 50%, 75%, and 100%
load
At 115 VAC and measured at the on-board
USB Type-C™ receptacle 91.7 %
ηave
Four-point average efficiency
25%, 50%, 75%, and 100%
load
At 230 VAC and measured at the on-board
USB Type-C™ receptacle 91.5 %
Output parameters - 15 V setting
VOUT Output voltage
VIN = 90 VRMS~264 VRMS
IOUT = 0 A~3 A 15 V
Vripple Output voltage ripple Peak-to-peak value with 20 MHz
bandwidth 164 250 mV
IOUT Output current 0 3 A
POUT Continuous output power 0 45 W
ηave
Four-point average efficiency
25%, 50%, 75%, and 100%
load
At 115 VAC and measured at the on-board
USB Type-C™ receptacle 91.7 %
ηave
Four-point average efficiency
25%, 50%, 75%, and 100%
load
At 230 VAC and measured at the on-board
USB Type-C™ receptacle 91.8 %
Output parameters - 20 V setting
VOUT Output voltage
VIN = 90 VRMS~264 VRMS
IOUT = 0 A~3.25 A 20 V
Vripple Output voltage ripple Peak-to-peak value with 20 MHz
bandwidth 268 300 mV
IOUT Output current 0 3.25 A
POUT Continuous output power 0 65 W
ηave
Four-point average efficiency
25%, 50%, 75%, and 100%
load
At 115 VAC and measured at the on-board
USB Type-C™ receptacle 91.7 %
ηave
Four-point average efficiency
25%, 50%, 75%, and 100%
load
At 230 VAC and measured at the on-board
USB Type-C™ receptacle 92.1 %
Ambient and EMI parameters
TAMB Ambient temperature Free convection sea level 0 25 40 °C
EMI Conducted EMI Meets CISPR32B /EN55032
TN1402
Specifications
TN1402 - Rev 2 page 5/35
3Test setup
3.1 Test conditions and equipment
• 1 x STDES-65ACFADP reference design
• 1 x 61604A programmable AC source by Chroma
• 1 x 63600-5 DC E-load by Chroma
• 1 x WT500 power analyzer by YOKOGAWA
• 1 x MSO44 mixed signal oscilloscope by Tektronix
• 1 x 8845A 6-1/2 digit precision multimeter by FLUKE
• 1 x P-NUCLEO-USB002 kit (sink emulator) to connect to the USB Type-C™ output to adjust the output
voltage
• Ambient temperature = 25°C
Figure 4. STDES-65ACFADP test setup
1
4
6
7
3
2
5
TN1402
Test setup
TN1402 - Rev 2 page 6/35
3.2 Procedure
Follow the steps below to test the reference design.
Step 1. Connect the STDES-65ACFADP USB Type-C™ output to the P-NUCLEO-USB002 kit via a USB
Type-C™ cable.
Step 2. Connect the P-NUCLEO-USB002 to a PC computer via a USB Type-A cable.
Step 3. Connect the AC source to the STDES-65ACFADP AC input L/N cables.
Step 4. Power up the STDES-65ACFADP with a 110 VAC or 230 VAC input to start the test.
Step 5. Adjust the output voltage through the P-NUCLEO-USB002.
Step 6. Adjust the output current through the E-load.
TN1402
Procedure
TN1402 - Rev 2 page 7/35
4Measurements/waveforms/test data
4.1 Efficiency test results
We tested the STDES-65ACFADP efficiency at 115 VAC and 230 VAC with different output voltages (5, 9, 12, 15,
and 20 V).
The obtained results show that our reference design meets the EU CoC Rev.05 Tier 2 and DoE Level 6
requirements with an adequate margin.
4.1.1 Efficiency at 115 VAC input
Figure 5. STDES-65ACFADP efficiency at 115 VAC input
Table 2. STDES-65ACFADP efficiency at 115 VAC input with different input voltages
Condition Percentage of full loading 5 V 9 V 12 V 15 V 20 V
EU CoC Rev.05-Tier2 limit for 10% loading - 72.48% 77.30% 78.30% 78.85% 78.85%
115 VAC 60 Hz input
10% 83.33% 84.92% 86.56% 86.45% 85.64%
25% 88.70% 89.83% 90.73% 90.73% 90.45%
50% 90.18% 91.32% 91.91% 91.89% 91.86%
75% 91.05% 91.39% 92.25% 92.21% 91.90%
100% 90.58% 91.90% 91.88% 91.95% 92.40%
Four-point average 90.13% 91.11% 91.69% 91.70% 91.65%
EU CoC Rev.05-Tier2 limit - 81.84% 87.30% 88.30% 88.85% 88.85%
TN1402
Measurements/waveforms/test data
TN1402 - Rev 2 page 8/35
4.1.2 Efficiency at 230 VAC input
Figure 6. STDES-65ACFADP efficiency at 230 VAC input
Table 3. STDES-65ACFADP efficiency at 230 VAC input with different input voltages
Condition Percentage of full loading 5 V 9 V 12 V 15 V 20 V
EU CoC Rev.05-Tier2 limit for 10% loading - 72.48% 77.30% 78.30% 78.85% 78.85%
230 VAC 50 Hz input
10% 83.87% 84.14% 84.80% 84.07% 84.58%
25% 85.46% 87.90% 89.68% 90.00% 89.91%
50% 86.99% 89.74% 91.12% 91.43% 91.95%
75% 90.29% 91.20% 92.19% 92.42% 92.83%
100% 90.65% 92.11% 92.76% 93.01% 93.70%
Four-point average 88.35% 90.24% 91.44% 91.72% 92.10%
EU CoC Rev.05-Tier2 limit - 81.84% 87.30% 88.30% 88.85% 88.85%
4.2 Load and line regulation test results
Table 4. Load and line regulation at 5 VOUT
Loading (%) 115 VAC (V) 230 VAC (V) SPEC limit (V)
0 5.10 5.11
4.85 5.15
10 4.88 4.89
20 4.87 4.88
33 4.93 4.91
50 5.02 5.01
75 5.02 5.02
83 5.02 5.03
100 5.02 5.03
TN1402
Load and line regulation test results
TN1402 - Rev 2 page 9/35
Table 5. Load and line regulation at 9 VOUT
Loading (%) 115 VAC (V) 230 VAC (V) SPEC limit (V)
0 9.08 9.09
8.73 9.27
10 9.07 9.08
25 9.06 9.09
50 9.07 9.07
75 9.06 9.05
100 9.02 9.02
Table 6. Load and line regulation at 12 VOUT
Loading (%) 115 VAC (V) 230 VAC (V) SPEC limit (V)
0 12.05 12.08
11.64 12.36
10 11.85 11.86
20 11.87 11.87
50 11.88 11.89
75 11.87 11.90
100 11.85 11.88
Table 7. Load and line regulation at 15 VOUT
Loading (%) 115 VAC (V) 230 VAC (V) SPEC limit (V)
0 15.08 15.08
14.55 15.45
10 15.06 15.09
25 15.05 15.04
50 15.06 15.06
75 15.05 15.06
100 15.02 15.00
Table 8. Load and line regulation at 20 VOUT
Loading (%) 115 VAC (V) 230 VAC (V) SPEC limit (V)
0 20.05 20.06
19.4 20.6
10 20.03 20.03
25 20.02 20.03
50 20.01 20.02
75 20.01 20.01
100 20.00 20.00
4.3 Ripple and noise
4.3.1 Test setup of the VOUT ripple and noise
To test the VOUT ripple and noise, we added a 10 µF electrolytic capacitor and a 100 nF ceramic capacitor at the
end of the USB Type-C™ cable, as shown below.
TN1402
Ripple and noise
TN1402 - Rev 2 page 10/35
Inhaltsverzeichnis
Andere ST Computerhardware Handbücher
ST
ST X-NUCLEO-IDB05A2 Bedienungsanleitung
ST
ST MotionTL Bedienungsanleitung
ST
ST EVLKST8500GH-2 Bedienungsanleitung
ST
ST EVSPIN948 Bedienungsanleitung
ST
ST STM32F101 series Bedienungsanleitung
ST
ST STEVAL-IFP045V1 Bedienungsanleitung
ST
ST X-NUCLEO-OUT11A1 Bedienungsanleitung
ST
ST STEVAL-SCR002V1 Bedienungsanleitung
ST
ST UM2727 Bedienungsanleitung
ST
ST UPSD3212A Bedienungsanleitung
ST
ST UM3019 Bedienungsanleitung
ST
ST STEVAL-IFP047V1 Bedienungsanleitung
ST
ST STEVAL-USBI2CFT Bedienungsanleitung
ST
ST ST7LITEUS2 Bedienungsanleitung
ST
ST UM2033 Bedienungsanleitung
ST
ST FP-SNS-FLIGHT1 Bedienungsanleitung
ST
ST X-NUCLEO-OUT10A1 Bedienungsanleitung
ST
ST STM32 Nucleo Bedienungsanleitung
ST
ST X-NUCLEO-IHM04A1 Bedienungsanleitung
ST
ST X-NUCLEO-USBPDM1 Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
