ST STDES-PFCBIDIR Bedienungsanleitung
Introduction
The STDES-PFCBIDIR reference design represents a complete solution for high-power, three-phase active front end (AFE)
rectifier applications based on the three-level T-Type topology.
This reference design topology is mostly used for DC fast charging applications related to industrial and electric vehicles.
It features full-digital control. The embedded STM32G474RET3 mixed-signal high-performance microcontroller provides the full
control of the power factor (PF), the DC voltage, and the auxiliary task to manage the grid connection and the soft startup
procedure.
The high-bandwidth continuous conduction mode (CCM) current regulation allows the maximum power quality in terms of total
harmonic distortion (THD) and power factor (PF).
Figure 1. DC charging station
How to use the STDES-PFCBIDIR reference design
UM2979
User manual
UM2979 - Rev 1 - February 2022
For further information contact your local STMicroelectronics sales office.
www.st.com
Figure 2. STDES-PFCBIDIR reference design - power board
Fully assembled board developed for
performance evaluation only,
not available for sale
Figure 3. STDES-PFCBIDIR reference design - control board
Fully assembled board developed for
performance evaluation only,
not available for sale
The high switching frequency of the SiC MOSFETs (70 kHz) and the multilevel structure allow an efficiency of almost 99% as
well as the optimization of passive power components in terms of size and cost.
The high efficiency bidirectional rectifier is designed for several end applications such as electric vehicle (EV), industrial battery
chargers, and industrial equipment, which requires a very high PF and low THD.
The STDES-PFCBIDIR is a fully assembled kit developed for performance evaluation only, not available for sale.
UM2979
UM2979 - Rev 1 page 2/70
1Getting started
1.1 Safety information
Caution: This reference design is intended for demonstration purposes only and is not for domestic or industrial
installations.
Danger: The high-voltage levels used to operate the reference design can cause serious injury,
electrical shock, and even death.
This reference design is intended for use by experienced power electronics professionals
who understand the necessary precautions against potential dangers and risks while
operating this board, even when it is not powered. The qualified personnel must be familiar
with the installation, use, and maintenance of power electrical systems. During operation, do
not touch the board as some of its components could reach a very high temperature.
1.2 Block diagram
Figure 4. STDES-PFCBIDIR block diagram
1.3 Features
• 3-phase, 3-level bidirectional AC-DC power converter:
–Rated nominal DC voltage: 800 VDC
– Rated nominal AC voltage: 400 VAC at 50 Hz
– Nominal power: 15 kW
• AC to DC rectifier mode:
– Power factor: PF >0.99
– Inrush current control and soft startup
• DC to AC inverter mode:
– Active and reactive power control
– Integrated grid connection solution
UM2979
Getting started
UM2979 - Rev 1 page 3/70
• Power section based on SiC MOSFETs:
–High frequency operation (100 kHz)
– High efficiency: >98%
– Passive element weight and size reduction
• Control section based on STM32G474RET3 microcontroller:
– P2P compatible with other STDES 3-phase power converters
– Four integrated high-performance op-amps
– Control and monitoring interfaces: SWD, UART, I²C, DACs
– 64-pin digital power connector
– Overcurrent and overvoltage protection
1.4 Main characteristics
Table 1. Main characteristics
Description Symbol Min. Typ. Max. Unit Comments
Three-phase input voltage VAC 208 400 VACLL
AC line frequency Hz 47 63 Hz
Maximum output power POUTmax
15
7kW
VAC = 230 VRMS IAC = 21 VRMS
VAC = 110 VRMS IAC = 21 VRMS
Output voltage VDC 800 V
Power factor PF >0.99 - From 20% of load
Total harmonic distortion THDi <5 % From 20% of load
Switching frequency fsw 70 kHz
Table 2. Protection characteristics
Description Symbol Min. Typ. Max. Unit
HVDC overvoltage protection VDCovp 900 V
HVCAP overvoltage protection VCAPovp 500 V
AC overcurrent protection IACovp 30 A
1.5 Reference design description
1.5.1 Power board
The figure below shows the power board of the STDES-PFCBIDIR reference design.
UM2979
Main characteristics
UM2979 - Rev 1 page 4/70
Figure 5. STDES-PFCBIDIR reference design - power board
The following figure shows the main sections of the power board.
Figure 6. STDES-PFCBIDIR power board sections
UM2979
Reference design description
UM2979 - Rev 1 page 5/70
1.5.2 Power stage
1.5.2.1 Boost inductor
Boost inductors are part of the LCL-R AC side filter. They allow obtaining the converter PFC operation by
controlling the inductor current using a proper conduction pattern in the power device section.
Continuous conduction mode (CCM) performs the PFC operation of this reference design. The inductance value
is related to several parameters: the current ripple, the available converter voltage levels, the switching frequency,
and the rated DC-AC operation voltages.
Table 3. Boost inductor parameters
Parameter Symbol Value
DC voltage (V) V0800
Switching frequency (kHz) fsw 70
Rated AC voltage (VRMS) VAC 230
Max. ripple current (%) ΔiLppmax 10
Boost inductance (H) L 470e-6
1.5.2.2 Inrush current limiter
Figure 7. Three and four-wire connections
Figure 8. Passive NTC
UM2979
Reference design description
UM2979 - Rev 1 page 6/70
Figure 9. STDES-PFCBIDIR NTC specifications
Figure 10. Active relays
1.5.2.3 Sensing
1.5.2.3.1 AC current
An isolated sensor measures the AC input current. It represents the boost inductor current to be controlled for the
proper operation of the PFC behavior of the power converter.
The output voltage of the Hall effect transducer is not in scale and contains a DC component of 2.5 V with respect
to the ADCs.
A conditioning circuit allows obtaining the correct value for the ADCs. The circuit shown below is replicated for
each phase.
UM2979
Reference design description
UM2979 - Rev 1 page 7/70
Figure 11. AC current sensing block diagram
1.5.2.3.2 AC voltage
The three-phase AC voltages are obtained using a two-stage sensor circuit. The first part represents an isolated
op-amp that allows measuring the HV through a voltage divider with an isolation barrier.
Isol-Op-AMP output is limited in volts and is scaled with a second stage of op-amps with a proper gain and bias.
This circuit allows measuring an AC voltage referenced by a virtual or grid neutral point. The circuit is replicated
for each phase.
Figure 12. AC voltage sensing block diagram
UM2979
Reference design description
UM2979 - Rev 1 page 8/70
1.5.2.3.3 DC current
An isolated sensor measures the DC output current. Hall sensors are taken into consideration. A conditioning
circuit allows obtaining the correct value for the ADCs.
Figure 13. DC current sensing block diagram
1.5.2.3.4 DC voltage
The DC voltages are obtained using two-stage sensing. The total DC bus voltage is split exploiting two voltage
dividers. Both voltages are needed to obtain the monitoring of each capacitor to avoid overvoltage, offering
independent DC voltages for the control.
UM2979
Reference design description
UM2979 - Rev 1 page 9/70
Figure 14. DC voltage sensing block diagram
1.5.3 Control board
The figure below shows the control board of the STDES-PFCBIDIR reference design.
Figure 15. STDES-PFCBIDIR reference design - control board
The following figure shows the main sections of the control board.
UM2979
Reference design description
UM2979 - Rev 1 page 10/70
Inhaltsverzeichnis
Andere ST Computerhardware Handbücher
ST
ST STR9 Bedienungsanleitung
ST
ST X-NUCLEO-STMODA1 Bedienungsanleitung
ST
ST X-NUCLEO-DRP1M1 Bedienungsanleitung
ST
ST STM32Cube Bedienungsanleitung
ST
ST STM32F4 Series Betriebsanleitung
ST
ST STEVAL-ISQ008V1 Bedienungsanleitung
ST
ST X-NUCLEO-IHM02A1 Bedienungsanleitung
ST
ST X-NUCLEO-GFX02Z1 Bedienungsanleitung
ST
ST X-NUCLEO-EEPRMA2 Bedienungsanleitung
ST
ST STEVAL-IDB013V1 Administratorhandbuch
ST
ST STSW-L9961BMS Bedienungsanleitung
ST
ST EVAL6470H-DISC Bedienungsanleitung
ST
ST AN1235 Montage- und Bedienungsanleitung
ST
ST STM32G0 Bedienungsanleitung
ST
ST STM8SVLDISCOVERY Montage- und Bedienungsanleitung
ST
ST ST25DV-DISCOVERY Bedienungsanleitung
ST
ST STEVAL-CCH002V1 Bedienungsanleitung
ST
ST STEVAL-ISF001V1 Bedienungsanleitung
ST
ST X-NUCLEO-LED12A1 Bedienungsanleitung
ST
ST EVSPIN948 Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
