ST STEVAL-IDB007V1M SPBTLE-1S Bedienungsanleitung

July 2017

DocID030868 Rev 1

1/55

www.st.com

UM2264

User manual

Getting started with the STEVAL-IDB007V1M SPBTLE-1S module

development kit

Introduction

The SPBTLE-1S module is a low power Bluetooth®smart system-on-chip, compliant with the Bluetooth®

v4.2 specification and supporting master, slave and simultaneous master-and-slave roles.

The available kit is the STEVAL-IDB007V1M development platform (order code: STEVAL-IDB007V1M).

The STEVAL-IDB007V1M provides a set of hardware resources for a wide range of application

scenarios: sensor data (accelerometer, pressure and temperature sensor), remote control (buttons and

LEDs) and debug message management through USB virtual COM. Three power options are available

(USB only, battery only and external power supply plus USB) for high application development and

testing flexibility.

Figure 1: STEVAL-IDB007V1M development platform

Contents

UM2264

2/55

DocID030868 Rev 1

Contents

1Getting started.................................................................................7

1.1 Kit contents .......................................................................................7

1.2 System requirements........................................................................7

1.3 BlueNRG-1 development kit setup....................................................7

2Hardware description......................................................................8

2.1 STEVAL-IDB007V1M1 board overview.............................................8

2.2 SPBTLE-1S module connections......................................................9

2.3 Power supply...................................................................................11

2.4 Jumpers ..........................................................................................11

2.5 Sensors...........................................................................................11

2.6 Extension connector........................................................................12

2.7 Push-buttons...................................................................................12

2.8 JTAG connector..............................................................................12

2.9 LEDs...............................................................................................12

2.10 STM32L151CBU6 microcontroller...................................................12

2.11 Current measurements ...................................................................12

2.12 Hardware setup...............................................................................13

3BlueNRG-1 Navigator....................................................................14

3.1 BlueNRG-1 Navigator ‘Demonstration Applications’ .......................14

3.1.1 BlueNRG-1 Navigator ‘Basic examples’........................................... 16

3.1.2 BlueNRG-1 Navigator ‘BLE demonstration and test applications’ ... 16

3.1.3 BlueNRG-1 Navigator ‘Peripherals driver examples’ ....................... 17

3.2 BlueNRG-1 Navigator ‘Development Kits’.......................................18

3.2.1 BlueNRG-1 Navigator ‘Release Notes’ and ‘License’ ...................... 18

4BlueNRG-1 Flasher utility .............................................................19

4.1 How to run.......................................................................................19

4.2 Main user interface window.............................................................20

4.2.1 Main menu items.............................................................................. 20

4.2.2 Image file selection........................................................................... 21

4.2.3 ‘Image File’ tab ................................................................................. 21

4.2.4 ‘Device Memory’ tab ......................................................................... 21

4.2.5 Using BlueNRG-1 Flasher utility with other boards.......................... 22

5Programming with BlueNRG-1 system-on-chip..........................24

UM2264

Contents

DocID030868 Rev 1

3/55

5.1 Software directory structure ............................................................24

6BlueNRG-1 Beacon demonstration application ..........................25

6.1 BLE Beacon application setup ........................................................25

6.1.1 Initialization....................................................................................... 25

6.1.2 Define advertising data..................................................................... 25

6.1.3 Entering non-connectable mode ...................................................... 25

7BlueNRG-1 chat demo application...............................................27

7.1 Peripheral and central device setup................................................27

7.1.1 Initialization....................................................................................... 27

7.1.2 Add service and characteristics........................................................ 28

7.1.3 Enter connectable mode................................................................... 28

7.1.4 Connection with central device......................................................... 28

8BLE chat master and slave demo application.............................30

8.1 BlueNRG-1 chat master and slave roles.........................................30

8.1.1 Initialization....................................................................................... 30

8.1.2 Add service and characteristics........................................................ 31

8.1.3 Start discovery procedure ................................................................ 31

8.1.4 Enter connectable mode................................................................... 31

8.1.5 Connection with chat master and slave client device....................... 31

9BlueNRG-1 remote control demo application..............................32

9.1 BLE remote control application setup..............................................32

9.1.1 Initialization....................................................................................... 32

9.1.2 Define advertising data..................................................................... 33

9.1.3 Add service and characteristics........................................................ 33

9.1.4 Connection with a BLE Central device............................................. 33

10 BlueNRG-1 sensor profile demo...................................................34

10.1 BlueNRG app for smartphones.......................................................35

10.2 BlueNRG-1 sensor profile demo: connection with a central device.35

10.2.1 Initialization....................................................................................... 35

10.2.2 Add service and characteristics........................................................ 36

10.2.3 Enter connectable mode................................................................... 36

10.2.4 Connection with central device......................................................... 36

11 BlueNRG-1 sensor profile central demo......................................37

12 BlueNRG-1 HID/HOGP demonstration application......................38

12.1 BLE HID/HOGP mouse demonstration application.........................38

Contents

UM2264

4/55

DocID030868 Rev 1

12.2 BLE HID/HOGP keyboard demonstration application.....................38

13 BlueNRG-1 throughput demonstration application ....................39

13.1 BLE unidirectional throughput scenario...........................................39

13.2 BLE bidirectional throughput scenario.............................................39

14 BLE notification consumer demonstration application..............41

15 BlueNRG-1 peripheral driver examples .......................................42

15.1 ADC examples................................................................................42

15.2 GPIO examples...............................................................................42

15.3 I²C examples...................................................................................43

15.4 Micro examples...............................................................................43

15.5 RTC examples ................................................................................44

15.6 SPI examples..................................................................................44

15.7 SysTick examples...........................................................................45

15.8 Timers examples.............................................................................45

15.9 UART examples..............................................................................47

15.10 WDG examples...............................................................................47

16 Schematic diagrams......................................................................48

17 Revision history ............................................................................54

UM2264

List of tables

DocID030868 Rev 1

5/55

List of tables

Table 1: STEVAL-IDB007V1M board component descriptions..................................................................9

Table 2: SPBTLE-1S module pin description with board functions............................................................9

Table 3: STEVAL-IDB007V1M kit platform power supply modes ............................................................11

Table 4: STEVAL-IDB007V1M kit platform jumpers.................................................................................11

Table 5: BlueNRG-1 Beacon advertising manufacturing data..................................................................25

Table 6: Serial port configuration..............................................................................................................27

Table 7: BLE remote advertising data ......................................................................................................32

Table 8: Document revision history ..........................................................................................................54

List of figures

UM2264

6/55

DocID030868 Rev 1

List of figures

Figure 1: STEVAL-IDB007V1M development platform ..............................................................................1

Figure 2: STEVAL-IDB007V1M board components ...................................................................................8

Figure 3: BlueNRG-1 Navigator................................................................................................................14

Figure 4: BLE Beacon application ............................................................................................................15

Figure 5: BLE Beacon Flash programming...............................................................................................15

Figure 6: BLE Beacon documentation......................................................................................................16

Figure 7: Basic examples .........................................................................................................................16

Figure 8: BLE demonstration and test applications..................................................................................17

Figure 9: Peripherals driver examples......................................................................................................17

Figure 10: STEVAL-IDB007V1M Kit components ....................................................................................18

Figure 11: BlueNRG-1 Flasher utility........................................................................................................19

Figure 12: BlueNRG-1 Flasher utility main window..................................................................................20

Figure 13: BlueNRG-1 Flasher utility file selection...................................................................................21

Figure 14: BlueNRG-1 Flasher utility image file viewer............................................................................21

Figure 15: BlueNRG-1 Flasher utility device memory viewer...................................................................22

Figure 16: BlueNRG-1 Flasher utility changing memory fields.................................................................22

Figure 17: BlueNRG-1 Flasher utility ‘Comport Setting’ popup ................................................................23

Figure 18: BLE chat client.........................................................................................................................29

Figure 19: BLE chat server.......................................................................................................................29

Figure 20: BLE sensor demo GATT database .........................................................................................34

Figure 21: BlueNRG sensor app...............................................................................................................35

Figure 22: STEVAL-IDB007V1M Arduino connectors..............................................................................48

Figure 23: STEVAL-IDB007V1M JTAG....................................................................................................48

Figure 24: STEVAL-IDB007V1M SPBTLE-1S module (BlueNRG-1).......................................................49

Figure 25: STEVAL-IDB007V1M power management and sensors ........................................................50

Figure 26: STEVAL-IDB007V1M buttons and LEDs ................................................................................51

Figure 27: STEVAL-IDB007V1M STM32 microprocessor........................................................................52

Figure 28: STEVAL-IDB007V1M USB, level translator, JTAG for micro..................................................53

Figure 29: STEVAL-IDB007V1M EEPROM/SWITCH..............................................................................53

UM2264

Getting started

DocID030868 Rev 1

7/55

1 Getting started

1.1 Kit contents

The STEVAL-IDB007V1M kit includes:

an SPBTLE-1S module development platform

a 2.45 GHz module integrated Bluetooth antenna

a USB cable

1.2 System requirements

The BlueNRG-1 Navigator and Flasher PC applications require:

PC with Intel®or AMD®processor running one of the following Microsoft®operating

systems:

Windows XP SP3

Windows Vista

Windows 7

At least 128 MB of RAM

USB ports

At least 40 MB of available hard disk space

Adobe Acrobat Reader 6.0 or later

1.3 BlueNRG-1 development kit setup

After downloading the BlueNRG-1 DK software package (STSW-BLUENRG1-DK) from

www.st.com, extract BlueNRG-1_DK-x.x.x-Setup.zip contents to a temporary directory,

launch BlueNRG-1-DK-x.x.x-Setup.exe and follow the on-screen instructions.

EWARM Compiler 7.70 or later is required for building the BlueNRG1_DK_x.x.x

demonstration applications.

Keil MDK-ARM and Atollic-True Studio toolchains are also supported.

Hardware description

UM2264

8/55

DocID030868 Rev 1

2 Hardware description

2.1 STEVAL-IDB007V1M1 board overview

The SPBTLE-1S module in the STEVAL-IDB007V1M development kit lets you experiment

with BlueNRG-1 system-on-chip functions. It features:

Bluetooth®SMART board based on the BlueNRG-1 Bluetooth low energy system-on-

chip

Associated BlueNRG-1 development kit software package including firmware and

documentation

Up to +5 dBm available output radiated power (by the module integrated antenna)

Excellent receiver sensitivity (-88 dBm)

Very low power consumption: 7.7 mA RX and 8.3 mA TX at -2 dBm

Bluetooth®low energy compliant, supports master, slave and simultaneous master-

and-slave roles

SMA connector for antenna or measuring equipment

3 user LEDs

2 user buttons

3D digital accelerometer and 3D digital gyroscope

MEMS pressure sensor with embedded temperature sensor

Battery holder

JTAG debug connector

USB to serial bridge for providing I/O channel with the BlueNRG-1 device

Jumper for measuring current for BlueNRG-1 only

RoHS compliant

The following figure and table describe physical sections of the board.

Figure 2: STEVAL-IDB007V1M board components

UM2264

Hardware description

DocID030868 Rev 1

9/55

Table 1: STEVAL-IDB007V1M board component descriptions

Region

Description

SPBTLE-1S module

Micro USB connector for power supply and I/O

JTAG connector

RESET button

two USER buttons

LPS25HB MEMS pressure sensor with embedded temperature

LSM6DS3 3D digital accelerometer and 3D digital gyroscope

PWR LED

three user LEDs

back of the

PCB

battery holder for two AAA batteries

J, L

Two rows of Arduino-compliant connectors

STM32L151CBU6 48-pin microcontroller (USB to serial bridge for I/O channel to PC

communication)(1)

ST2378E level translator to adapt voltage level between STM32 and SPBTLE-1S

Notes:

(1)STM32 is not intended to be programmed by users

2.2 SPBTLE-1S module connections

The SPBTLE-1S module, containing the very low power Bluetooth low energy (BLE) single-

mode system-on-chip (Figure 2: "STEVAL-IDB007V1M board components" –region A) has

160 KB, 256 KB of Flash, 24 KB of RAM, a 32-bit core ARM®Cortex®-M0 processor and

several peripherals (ADC, GPIOs, I²C, SPI, Timers, UART, WDG and RTC).

The microcontroller is connected to various components such as buttons, LEDs and

sensors. The following table describes the microcontroller pin functions.

Table 2: SPBTLE-1S module pin description with board functions

name

no.

Board function

LED

Micro

Button

Pressure

sensor

accelerometer

and

gyroscope

JTAG

Arduino connectors

CN1

CN2

CN3

CN4

DIO10

JTMS-

SWTDIO

DIO9

JTCK-

SWTCK

DIO8

TXD

(PA2)

pin 1

IO8

pin 2

Hardware description

UM2264

10/55

DocID030868 Rev 1

name

no.

Board function

LED

Micro

Button

Pressure

sensor

accelerometer

and

gyroscope

JTAG

Arduino connectors

CN1

CN2

CN3

CN4

DIO7

DL2

pin 2

IO9

pin 6

SCL

DIO6

DL1

pin 7

IO6

pin 5

SDA

DIO5

SDA

PUSH2

button

pin 9

SDA

DIO4

SCL

DIO3

SDO/SA0

pin 5

MIS

pin 6

IO5

DIO2

SDA

pin 4

MOS

pin 5

IO4

DIO1

JTAG-

TDO

pin 3

DIO0

SCL

JTAG-

TDI

pin 6

SCK

pin 4

IO3

ANATES

T0/

DIO14

DL3

pin 4

AD3

ANATES

ADC1

ADC2

VBAT

RESETN

RESET

pin 3

NRST

pin 8

IO7

DIO13

PUSH1

pin 3

AD2

DIO12

INT1

pin 1

AD0

DIO11

RXD

PA3

pin 1

pin 3

IO2

pin 2

AD1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ST Mikrocontroller Handbücher

ST STM32H7 3 Series Montage- und Bedienungsanleitung

ST 32F429IDISCOVERY Bedienungsanleitung

ST iNEMO STEVAL-MKI062V2 Series Bedienungsanleitung

ST EVLKST8500GH868 Bedienungsanleitung

ST STM32C0 Series Montage- und Bedienungsanleitung

ST STM32MP157C-DK2 Bedienungsanleitung

ST SPC56A Series Bedienungsanleitung

ST STM32F101 series Bedienungsanleitung

ST STM32L4 Series Bedienungsanleitung

ST STM32 Nucleo Bedienungsanleitung

ST STM32 Nucleo Montage- und Bedienungsanleitung

ST STM32F205 series Bedienungsanleitung

ST STM32F40 Series Bedienungsanleitung

ST SimpleMAC STM32W108 Series Bedienungsanleitung

ST STEVAL-MKSBOX1V1 Bedienungsanleitung

ST STM32F7308-DK Bedienungsanleitung

ST STM32 Nucleo Montage- und Bedienungsanleitung

ST STM32F31xx Bedienungsanleitung

ST L638E Series Benutzerhandbuch

ST Turbo uPSD DK3300-ELCD Bedienungsanleitung

ST STM32G4 Series Bedienungsanleitung

ST STM32F0 Series Betriebsanleitung

ST STM32F423 Series Bedienungsanleitung

ST STM8S Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung