ST STEVAL-ISB68WTX Bedienungsanleitung

Introduction

The STEVAL-ISB68WTX evaluation board based on STWLC68JRF designed for wireless power transmitter application.

STWLC68JRF can deliver up to 2.5 W power to a Qi complaint wireless receiver.

Fully integrated STWLC68JRF require few external components for board design and can work with 5-20 V input power supply.

With External USB-to-I2C bridge, the user can monitor and control the STWLC68JRF chip with the STSW-ISB68PRO Graphical

User Interface (GUI).

The STEVAL-ISB68WTX includes several safety mechanisms providing over-temperature, over-current and over-voltage

protection as well as Foreign Object Detection (FOD).

Figure 1. STEVAL-ISB68WTX

Getting started with STEVAL-ISB68WTX for 2.5W TX application

UM2901

User manual

UM2901 - Rev 1 - July 2021

For further information contact your local STMicroelectronics sales office.

www.st.com

1Board Overview

The STEVAL-ISB68WTX evaluation board default configuration is optimized for performance.

The board features:

•STWLC68JRFwireless power transmitter chip with up to 2.5 W output power capability

• Low power applications with 5 V input voltage (supplied externally or USB adapter)

• Very few external components, optimized BOM and PCB space

• On chip high efficiency full bridge inverter

• Embedded ARM Cortex™-M0+ Processor

• Wide input operating range 5 V to 20 V

• 8-channels, 10-bit A/D Converter

• On-chip thermal management and protections (over-voltage, over-current, over-temperature)

• Foreign Object Detection (FOD) supported

• 400 kHz I2C interface for communication with host system (optional)

•External USB-to-I2C converter for interfacing to STWLC68JRF chip

• On-chip thermal management and protections (over-voltage, over-current, over-temperature)

• Foreign Object Detection (FOD) supported

• 400 kHz I2C interface for communication with host system (optional)

• External USB-to-I2C converter for interfacing to STWLC68JRF chip

• Complete kit (board with embedded receiving coil, Graphical User Interface control software)

• Chip-Scale Package (CSP), ROHS Complaint

UM2901

Board Overview

UM2901 - Rev 1 page 2/18

2Board configuration

The configuration settings of the STWLC68JRF chip are retrieved from the OTP memory at power-up, but they

can be temporary changed via GUI once the ISB68WTX is powered and the modified values are kept until a reset

of chip occurs.

The default STWLC68JRF settings are the following:

• The coil and resonant capacitors are designed for delivering 2.5 W using 5 V supply

• The output load to be adjusted gradually in steps of 10 mA to avoid high load transient

• The output current limit is set to 2 A

• The inverter maximum operating frequency set to 205 kHz, minimum operating frequency set to 110 kHz

• The duty cycle range minimum 20%, maximum 50%

• The ping frequency is set to 150Khz, ping interval set to 2seconds

• External TX device monitor feature is enabled

• TX Ping is disabled when external TX is detected

• TX Control Error Packet (CEP) time out set to 800msecs

• Frequency HOP frequency used in case of ASK modulation failure is set to 2900 Hz

• Control Error Packet time out max count set to 6

• Following interrupts are enabled by default

– Over Temperature Protection Interrupt (OTP)

– Over Current Protection Interrupt (OCP)

– End of Power Transfer Packet Interrupt (EPT)

– EXT TX device detect interrupt

• Switch to Qi TX Mode is disabled, need to enable it for starting TX mode

• Enable Tx ping can be used to start the ping (default it is enabled) disable TX ping

• Disable TX ping can be used to stop the Ping (power transfer will be terminated)

• Enable FOD detection (default it is disabled)

• Following Default Protection Threshold settings used

• Over Temperature Protection at 90 °C

• The default setting for the over-temperature protection consists in disabling the TX inverter output in case

one of the temperature sensors detects more than 90 °C

• Over Current Protection (OCP) at 2 A resulting in Tx Inverter output disconnection

• Over Voltage Protection (OVP) at 10 V resulting in Tx inverter output disconnection

2.1 Board configuration and test points

The STEVAL-ISB68WTX has several connectors and test points to ease access to key signals.

UM2901

Board configuration

UM2901 - Rev 1 page 3/18

Figure 2. Description of test points

Figure 3. STEVAL-ISB68WTX layout

2.2 Connection to USB I2C converter board

Connect external USB converter board to P3 connector, please ensure right connections for GND, SDA, SCL

pins , as shown in below picture.

UM2901

Connection to USB I2C converter board

UM2901 - Rev 1 page 4/18

Figure 4. STEVAL-ISB68WTX and USB-I2C converter

2.3 USB to I2C converter board

The USB to I2C bridging dongle is the tool that allows interfacing the receiver to the Graphical User Interface

running on a PC.

Three LEDs monitor the operation of the bridge:

D1 (green) indicates I2C bus activity.

D2 (red) indicates correct initialization of the U1 chip

D3 (yellow) is a power-on indicator.

When the dongle is plugged into the USB port, both D2 and D3 should be on.

Figure 5. USB-to-I2C converter

UM2901

USB to I2C converter board

UM2901 - Rev 1 page 5/18

2.4 Board power supply

The power to the board can be supplied using 5V/2A USB adapter, connected through J1 (microUSB receptacle)

or using external 5V power source.

Ensure a stable supply using high quality cables with minimal DC resistance for best overall efficiency.

2.5 Board configuration

The configuration settings of the STWLC68JRF chip are retrieved from the OTP memory at power-up, but they

can be temporary changed via GUI once the ISB68WTX is powered and the modified values are kept until a reset

of chip occurs.

The default STWLC68JRF settings are the following:

• The coil and resonant capacitors are designed for delivering 2.5 W using 5 V supply

• The output load to be adjusted gradually in steps of 10 mA to avoid high load transient

• The output current limit is set to 2 A

• The inverter maximum operating frequency set to 205 kHz, minimum operating frequency set to 110 kHz

• The duty cycle range minimum 20%, maximum 50%

• The ping frequency is set to 150Khz, ping interval set to 2seconds

• External TX device monitor feature is enabled

• TX Ping is disabled when external TX is detected

• TX Control Error Packet (CEP) time out set to 800msecs

• Frequency HOP frequency used in case of ASK modulation failure is set to 2900 Hz

• Control Error Packet time out max count set to 6

• Following interrupts are enabled by default

– Over Temperature Protection Interrupt (OTP)

– Over Current Protection Interrupt (OCP)

– End of Power Transfer Packet Interrupt (EPT)

– EXT TX device detect interrupt

• Switch to Qi TX Mode is disabled, need to enable it for starting TX mode

• Enable Tx ping can be used to start the ping (default it is enabled) disable TX ping

• Disable TX ping can be used to stop the Ping (power transfer will be terminated)

• Enable FOD detection (default it is disabled)

• Following Default Protection Threshold settings used

• Over Temperature Protection at 90 °C

• The default setting for the over-temperature protection consists in disabling the TX inverter output in case

one of the temperature sensors detects more than 90 °C

• Over Current Protection (OCP) at 2 A resulting in Tx Inverter output disconnection

• Over Voltage Protection (OVP) at 10 V resulting in Tx inverter output disconnection

UM2901

Board power supply

UM2901 - Rev 1 page 6/18

3Functional description

WPC Wireless charging system is shown in the below diagram.

The TX is responsible for controlling the transmitting coil and generating the correct amount

of power requested by the RX.

The RX continuously provides the transmitter with the correct power level requested, by modulating the

transmitter carrier through the controlled resistive or capacitive load. Generating the correct amount of power

ensures the highest level of end to-end efficiency due to reduced energy losses. It also helps maintaining a lower

operational temperature.

The TX can adapt to the amount of energy transferred by the coil by modulating the frequency, duty cycle or

amplitude of the PWM voltage on the transmitting coil.

Figure 6. Functional description

3.1 Power conversion

The power transmitter design uses a full bridge inverter to drive the primary coil and series capacitance. The

power transmitted to the coil is regulated by varying the switching frequency of bridge, higher the operating

frequency (example 200 kHz) for lower power transmission , lower operating frequency (example 110 kHz) for

Higher power transfer.

The coil used in the current design has self-inductance of 6.8 uH, the value of series capacitor 347 nF. The input

voltage to the Full bridge inverter is 5 V.

The LC resonant circuit optimization to be done based on power transfer requirements.

UM2901

Functional description

UM2901 - Rev 1 page 7/18

Figure 7. Power conversation

3.2 Communication and control

The 32-bit core MCU is the supervisor of the whole device and manages all the functional blocks to establish and

maintain communication with the receiver.

Ensure adherence to Qi standard specifications (wherever required), optimize the efficiency by properly adjusting

the operating point and guarantee reliability by monitoring and protecting the device.

3.3 ASK demodulation

Using ASK modulation, the receiver sent Control Error Packets (CEP) to tune operating point for matching load

requirements, the transmitter coil signals are filtered using demodulation filter circuit as shown below and feed in

to VS pin of STWLC68JRF.

UM2901

Communication and control

UM2901 - Rev 1 page 8/18

Figure 8. ASK demodulation circuit

3.4 FOD

STWLC68JRF has FOD detection feature. Any excess power loss in wireless power transfer can be monitored

and the device can stop power transfer.

The FOD detection is enabled by setting TX_FOD_EN bit to 1 in register 0x0021h.

The AUTO FOD detection threshold can be set in AUTO_FOD_THR register 0x00EBh.

FOD is detected when abs(PTX-PRX) > TX_AUTO_FOD_THR * 20mW (20mW unit).

PTX is TX power transferred to RX : Monitor register 0x0070h (2bytes)

PRX is TX Power received by RX : Monitor register 0x0072h (2bytes).

UM2901

FOD

UM2901 - Rev 1 page 9/18

4Component Layout

Figure 9. Component layout

UM2901

Component Layout

UM2901 - Rev 1 page 10/18

Inhaltsverzeichnis

Andere ST Mikrocontroller Handbücher

ST ST7LITE1 B Series Bedienungsanleitung

ST STEVAL-IPC004V1 Bedienungsanleitung

ST STM32F0DISCOVERY Bedienungsanleitung

ST STM32 Nucleo-64-P Series Bedienungsanleitung

ST STM32L4 5 Series Bedienungsanleitung

ST STM32H7 3 Series Montage- und Bedienungsanleitung

ST STM8S Bedienungsanleitung

ST STM32F103ZE Bedienungsanleitung

ST STM8A-DISCOVERY Bedienungsanleitung

ST BlueNRG Bedienungsanleitung

ST STEVAL-IDB007V1M SPBTLE-1S Bedienungsanleitung

ST STM32CubeL5 Bedienungsanleitung

ST STM32WL5 Series Bedienungsanleitung

ST STM32F101 series Bedienungsanleitung

ST STM32F4DISCOVERY Bedienungsanleitung

ST UM2135 Bedienungsanleitung

ST STM32L4x6 Bedienungsanleitung

ST UM2708 Bedienungsanleitung

ST STR9 Bedienungsanleitung

ST VD6283 Bedienungsanleitung

ST STEVAL-BFA001V1B Bedienungsanleitung

ST STM32F0DISCOVERY Bedienungsanleitung

ST STM8S Montage- und Bedienungsanleitung

ST L638E Series Benutzerhandbuch

Beliebte Mikrocontroller Handbücher anderer Marken

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F800 Bedienungsanleitung

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Bedienungsanleitung