ST EVAL-TDA7803A Bedienungsanleitung

Introduction

This note provides preliminary information about how to operate the boards offered to evaluate two components in FW27

package: TDA7803A and TDA7808.

This document describes how to use the evaluation board in order to check devices performance; for any other information and

deeper details please refer to the TDA7803A and TDA7808 datasheet (see Appendix A).

Evaluation board for TDA7803A and TDA7808 power amplifiers

UM2376

User manual

UM2376 - Rev 2 - August 2020

For further information contact your local STMicroelectronics sales office.

www.st.com

1Hardware description

1.1 Board description

Figure 1. EVAL-TDA7803A board Top view

UM2376

Hardware description

UM2376 - Rev 2 page 2/14

1.2 Application circuit

The basic application diagram is shown in Figure 2. A key components description and a suggestion about how to

choose the right components, are respectively shown in Table 1.

Figure 2. EVAL-TDA7803A application circuit

S CK

OUT RF / OUT3

OUT R R / OUT4

OUT LF / OUT1

OUT LR / OUT2

22µF

4.7µF

TAB

Vpull-up

Vcc 1 Vcc 2

14 17 16 25

47KΩ

21 18

DGND

AGND

CD/DIAG

S D2_4

S D1_3

0.22µF

2200µF

TDA7803A

TDA7808

I2S INP UT

I2C BUS DATA

CLK

V ST-BY

Note: • C3 and C4 capacitors must be SMD ceramic types.

• GND separations unnecessary if a dedicated ground layer is available at PCBoard level.

Table 1. EVAL-TDA7803A components description

Component

name

Recomm.

value

Min/Max

value Purpose Lower than

recomm.

Higher than

recomm. Notes

C1 0.1 μF 0.1 μF/0.47

μF ± 20% Vbatt HF filter

Danger of high

frequency

instabilities

Lower HF

suppression

low-ESR type (e.g.

X7R). Placed very

close to the IC

C2 2200 μF 1000 μF min Vbatt LF filte Higher ripple

Audio

performance

improvment

Standard electrolytic/

25 V. Reasonably

close to the IC

C3 4.7 μF 2.2 μF/10 μF

± 20%

Supply filter of

the IC's digital

section

instability dysfunction low-ESR type (e.g.

X7R)

C4 22 μF 10 μF/47 μF

Supply filter of

the IC's analog

section

instability dysfunction low-ESR type (e.g.

X7R)

R2 47 KΩ 10 KΩ/75 KΩ CD/DIAG pull-up dysfunction dysfunction -

UM2376

Application circuit

UM2376 - Rev 2 page 3/14

2Board operation

Before any operation, please insert the power amplifier in the socket provided with the board.

A heat-sink (not provided) has to be used. Please refer to Section 3 Power dissipation/Heat-sink to choose the

right heat-sink.

A supply voltage (battery voltage or equivalent) on VS-GND connectors, between 6 V and 18 V, is needed to

operate the board.

Please refer to datasheet to understand load impedance compatibility of power amplifiers, then connect resistive

loads (or speakers) to OUT1, OUT2, OUT3, OUT4 connectors.

I2S format (SDA, CLK, WS lines) has to be used for input audio signals.

I2C bus format (SDA, CLK lines) is necessary for sending any operation instructions to the IC.

HW Mute and Standby should be disabled (both are active low).

The TDA7803A power amplifier can only operate with I2C bus active.

The IC can work in high efficiency mode too (please, refer to datasheet). This operating mode can be selected

through the I2C bus.

UM2376

Board operation

UM2376 - Rev 2 page 4/14

3Power dissipation/Heat-sink

The heat-sink size / characteristics largely depend on the operating conditions and consequently power

dissipation levels are implied. Dissipation can be higher if sine test tones are used instead of music or audio-

simulation signals (e.g. Pink Noise).

Considering the standard car-radio conditions (Vs = 14 V, RL = 4 Ω, 4-CH operation), the Pdiss levels implied are

as follows (STD mode / SB-I mode @ Tamb = 70 °C , Tj-max = 150 °C):

• SINE WAVE: Pdiss = 42 W / 38 Rth htsk = 1.9 °C/W / 2.1 °C/W

• PINK NOISE: Pdiss = 30 W / 18 Rth htsk = 12.7 °C/W / 4.4 °C/W

If sine-wave trials (especially with 4-CH operation / RL = 2 Ω) are to be run, then the heatsink

has to be replaced by a larger / lower-Rth one.

UM2376

Power dissipation/Heat-sink

UM2376 - Rev 2 page 5/14

4High frequency output waveforms

In SB-I mode the speaker signal (OUT-OUT) is the sum of the signals at OUT+ and OUT- pins, which are not

sinusoidal (in STD mode they are). Here below it is reported an oscilloscope snapshot, which shows the output

waveforms in SB-I mode (@ Po > 2.5 W / 4 Ω).

Figure 3. Output signals in high efficiency mode

UM2376

High frequency output waveforms

UM2376 - Rev 2 page 6/14

5Demo board schematic

Figure 4. EVAL-TDA7803A Demo board schematic

UM2376

Demo board schematic

UM2376 - Rev 2 page 7/14

6Information on board use

This evaluation board/kit is intended to be used for ENGINEERING DEVELOPMENT, DEMONSTRATION OR

EVALUATION PURPOSES ONLY and it is not considered by ST Microelectronics (ST) a finished end product fit

for general consumer use. People handling the product(s) must have electronics training and observe good

engineering practice standards. As such, the goods being provided are not intended to be complete in terms of

required design-, marketing- and/or manufacturing-related protective considerations, including product safety and

environmental measures typically found in end products that incorporate such semiconductor components or

circuit boards. This evaluation board/kit does not fall within the scope of the European Union directives regarding

electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore

they may not meet the technical requirements of these directives or other related directives.

UM2376

Information on board use

UM2376 - Rev 2 page 8/14

Appendix A Reference documents

Table 2. Reference documents

Doc Name ID Title

DS12195 030745 High efficiency digital input automotive quad power amplifier with built-in diagnostics features, 'start stop'

compatible

DS12230 030826 High efficiency digital input automotive quad power amplifier, 'start stop' compatible

UM2376

Reference documents

UM2376 - Rev 2 page 9/14

Revision history

Table 3. Document revision history

Date Version Changes

05-Apr-2018 1 Initial release.

05-Aug-2020 2 Removed PSO package.

UM2376

UM2376 - Rev 2 page 10/14

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST eMotion STEVAL-MKI109V1 Bedienungsanleitung

ST STM3210C-EVAL Bedienungsanleitung

ST EVAL-L99H02QF Bedienungsanleitung

ST NUCLEO-8S207K8 Bedienungsanleitung

ST UM0527 Bedienungsanleitung

ST SPC563M64CAL144 Bedienungsanleitung

ST STM3210B-EVAL Bedienungsanleitung

ST SPC58NHADPT176S Bedienungsanleitung

ST STEVAL-LLL014V1 Bedienungsanleitung

ST STM32CubeH7 Bedienungsanleitung

ST STEVAL-BLUEMIC-1 Bedienungsanleitung

ST STEVAL-L99615C Bedienungsanleitung

ST STEVAL-IHM020V1 Bedienungsanleitung

ST P-NUCLEO-IOD01A1 Bedienungsanleitung

ST M24SR-DISCOVERY Bedienungsanleitung

ST STEVAL-IPP003V1 Kurzanleitung

ST STEVAL-ILL059V1 Bedienungsanleitung

ST SPC58XXMB Bedienungsanleitung

ST STUSB02E Bedienungsanleitung

ST STEVAL-ILH007V1 Bedienungsanleitung

ST AN3959 Montage- und Bedienungsanleitung

ST STM32429I-EVAL1 Bedienungsanleitung

ST STEVAL-AETKT2V1 Bedienungsanleitung

ST EnFilm EFL1K0AF39 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung