ST L9678-S-EVB Bedienungsanleitung

Introduction

The L9678-S-EVB evaluation board is an evaluation board designed to provide to the user a platform for the evaluation of the

L9678P or L9678P-S devices. The board provides all the main input/output capabilities needed to properly drive all IC inputs

and outputs and to provide diagnostic functionalities.

Evaluation board for L9678 airbag and battery cut-off IC

UM3144

User manual

UM3144 - Rev 1 - March 2023

For further information contact your local STMicroelectronics sales office.

www.st.com

1Hardware description

The L9678-S-EVB evaluation board has been developed to evaluate the L9678P or L9678P-S devices and test all

their functionalities.

Its main features are:

• L9678P/L9678P-S placed into a socket allowing an easy change of the samples

• Possibility to solder L9678P/L9678P-S directly on the PCB

• Total accessibility to all pins through test points

• Presence of jumpers to fix the desired set up configuration

• Possibility to interface the board with SPC56P-Discovery board

Figure 1. L9678-S-EVB evaluation board

UM3144

Hardware description

UM3144 - Rev 1 page 2/12

2Board layout

Figure 2. Assembly Top

Figure 3. Assembly Bottom

UM3144

Board layout

UM3144 - Rev 1 page 3/12

3Jumpers and connectors description

On Table 1 the name of each jumper on the board is listed while their default setting (closed or open) is reported

in green; the name of the connectors and test points present on the board is also remarked.

Table 1. Jumpers and connectors description

# Name J = Jumper

C = Connector Function Closed Open

J1 PGND J Connection of PGND to GND Power ground connected to

common ground(1) -

J2 WDT J To disable the watchdog timer Watchdog disabled Watchdog enabled(1)

J3 J To set VCC to 5 V or to 3.3 V

1-2 closed: VCC connected to

VDD3V3

2-3 closed: VCC connected to

VDD5(1)

J4 VBAT C Battery voltage - -

J5 IGN J To wake-up the device Device waked-up(1) Device not waked-up

J6 J

Connection of L9678 RESET

pin to GPIO or RESET pin of

μC

1-2 closed: RESET_L96xx

connected to uC RESET pin

2-3 closed: RESET_L96xx

connected to μC GPIO0 pin

J7 SAFING INPUT J

Connection of safing FET

gate to VSF directly or

through MUN5332DW

1-2 closed: safing FET

enabled via uC

2-3 closed: safing FET always

enabled

Safing FET disabled

J8 J To discharge the ER capacitor ER capacitor shorted to

ground

ER capacitor

charged(1)

J9 J To connect the ER cap

negative to ground

Cap negative connected to

ground(1)

Cap negative not

connected to ground

J10 HEADER34X4 C To connect the L9678 demo

board to discovery board - -

J11 J To connect ISOK bus 2-3 closed: ISO bus

enabled(1) -

J12 J Not used for L9678 -

J13 BGND J Connection of BGND to GND Boost ground connected to

common ground(1) -

J15 J Reserve voltage diagnostic

(VRES)

VRES can be connected to

ERBOOST, VBAT or VSUP

Reserve voltage is

not diagnosed

J16 J Not used for L9678

J17 J Connection of VCC to

VCC_Micro

VCC connected to

VCC_Micro

VCC and VCC_Micro

disconnected(1)

J18 C SPI interface connector - -

J19 C SPI interface connector - -

J20 AGND J Connection of AGND to GND Analog ground connected to

common ground(1) -

J28 J RSU power supply

1-2 closed: RSU power

supply connected to VSUP(1)

2-3 closed: not used for

L9678

No RSU power

supply

UM3144

Jumpers and connectors description

UM3144 - Rev 1 page 4/12

# Name J = Jumper

C = Connector Function Closed Open

J29 J To connect the ER cap

positive to VER

Cap positive connected to

VER(1)

Cap positive not

connected to VER

J30 C Airbag standard connector - -

1. Default condition.

UM3144

Jumpers and connectors description

UM3144 - Rev 1 page 5/12

4Test point list

Designator Name Function

TP1 FENH FENH monitoring

TP2 FENL FENL monitoring

TP3 COVRACT COVRACT monitoring

TP4 ACL ACL monitoring

TP5 ARM1 ARM/ARM1 monitoring

TP6 WDT WDT monitoring

TP7 ERBOOST ERBOOST monitoring

TP8 uc_SAFING Monitoring of μC safing FET enable

TP9 VIN monitoring

TP10 VDD3P3 VDD3P3 monitoring

TP11 BVSUP BVSUP monitoring

TP12 SAFING OUTPUT SAFING OUTPUT monitoring

TP13 VSUP VSUP monitoring

TP14 SS01 SS01 monitoring

TP15 SS23 SS23 monitoring

TP16 SS45 SS45 monitoring

TP17 SS67 SS67 monitoring

TP18 SS89 SS89 monitoring

TP19 SSAB SSAB monitoring

TP20 CVDD monitoring

TP21 VBATMON monitoring

TP22 BVVD5 BVVD5

TP23 VDD5 VDD5 monitoring

TP24 SYNCBOOST monitoring (only L9679/80)

TP25 Monitoring of Q5 collector voltage

TP26 Monitoring of μC diagnostic enable

TP27 SATBCK monitoring

TP28 VCC monitoring

TP29 RSU4 monitoring

TP30 RSU3 monitoring

TP31 RSU1 monitoring

TP32 RSU0 monitoring

TP33 GND GND monitoring

TP34 CS_RS CS_RS monitoring (only L9680)

TP35 SPI_CS SPI CS monitoring (only L9679/80)

TP36 GND GND monitoring

TP37 GND GND monitoring

TP38 GND GND monitoring

UM3144

Test point list

UM3144 - Rev 1 page 6/12

Designator Name Function

TP39 GND GND monitoring

UM3144

Test point list

UM3144 - Rev 1 page 7/12

Revision history

Table 2. Document revision history

Date Version Changes

02-Mar-2023 1 Initial release.

UM3144

UM3144 - Rev 1 page 8/12

Contents

1Hardware description ..............................................................2

2Board layout.......................................................................3

3Jumpers and connectors description ..............................................4

4Test point list ......................................................................6

Revision history ........................................................................8

UM3144

Contents

UM3144 - Rev 1 page 9/12

List of tables

Table 1. Jumpers and connectors description ......................................................4

Table 2. Document revision history ..............................................................8

UM3144

List of tables

UM3144 - Rev 1 page 10/12

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST STM32L4R9I-EVAL Bedienungsanleitung

ST STM32100E-EVAL Bedienungsanleitung

ST STM3240G-EVAL Bedienungsanleitung

ST STEVAL-BLUEPLUG1 Bedienungsanleitung

ST STEVAL-WESU1 Bedienungsanleitung

ST STEVAL-PCC008V1 Bedienungsanleitung

ST STM32429I-EVAL Bedienungsanleitung

ST STM32L4R9I Bedienungsanleitung

ST STEVAL-ISB68RX Bedienungsanleitung

ST STM8L1526-EVAL Bedienungsanleitung

ST STEVAL-SPIN3202 Bedienungsanleitung

ST UM0920 Bedienungsanleitung

ST NUCLEO-H745ZI-Q Bedienungsanleitung

ST ST9 EPB Bedienungsanleitung

ST STM32429I-EVAL1 Bedienungsanleitung

ST STM32L152-EVAL Bedienungsanleitung

ST UM2163 Bedienungsanleitung

ST STEVAL-ISB044V1 Bedienungsanleitung

ST NUCLEO-G070RB Bedienungsanleitung

ST STLINK-V3SET Bedienungsanleitung

ST SPC58NG-DISP Bedienungsanleitung

ST SPC560P-DISP Bedienungsanleitung

ST EVALSP1340CPU Bedienungsanleitung

ST SPC564A-DISP Montage- und Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung