ST SPC564A-DISP Montage- und Bedienungsanleitung

August 2017 DocID025693 Rev 2 1/7

AN4424

Application note

Getting started with SPC564A-DISP discovery board

Introduction

The SPC564A-DISP is an evaluation tool supporting STMicroelectronics SPC56 M Line

microcontrollers.

The discovery board SPC564A-DISP is based on SPC564A70L7 32-bit 150 MHz e200z4

Power Architecture®core, 2Mbyte on-chip in an LQFP176 package.The numerous

interfaces including CAN/SCI/K-LINE/DSPI/GPIO make the SPC56M-DISP an excellent

starter kit for customer quick evaluation and project development.

Figure 1. SPC564A-DISP Discovery Plus board with SPC564A70L7

The SPC56 M family is designed to address cost sensitive powertrain and transmission

applications.

The SPC56 M line key functionality is Time processing units (eTPU) a coprocessor to create

events in sync with internal or external signals without flooding the CPU with interrupt to

serve.

SPC5Studio is available for download www.st.com/spc5studio.

SPC5Studio comes with HighTec GNU "C" compiler free fully featured 30-day trial version.

An E2E Community is available on ST WEB:

https://my.st.com/public/STe2ecommunities/mcu.

The PCB, all components and all HW parts meet requirements of the applicable RoHS

directives.

www.st.com

Contents AN4424

2/7 DocID025693 Rev 2

Contents

1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Delivery Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.2 Setting up Hardware and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 How to connect SPC564A-DISP to a programmer/debugger . . . . . . . . 4

2.1 How to connect an adapter to the JTAG connector . . . . . . . . . . . . . . . . . . 4

Appendix A General handling precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

DocID025693 Rev 2 3/7

AN4424 Getting started

1 Getting started

1.1 Delivery Checklist

The SPC56A-Discovery kit contains the following items:

#1 SPC564A-DISP evaluation board.

1 Power supply (Output 5VDC, the center pin is positive).

The jumpers allow configuring the board to enable features and different flash modalities.

1.2 Setting up Hardware and Connections

To set up the hardware follow this procedure:

1. Remove the board and the PSU from the protective plastic envelopes.

2. Check the SPC563M-DISP board; the jumpers are already configured. Set the main

switch (S4) OFF position

3. Connect the PSU to the mains. Note: a mains plug adapter(a) can be used to connect

the PSU mains Europlug to your local mains socket.

4. Plug the PSU cable in the X4 connector (+5VDC input).

5. Set switch S4(ON)

6. The board is now supplied and ready to be used and programmed.

7. The LED LE3 (red) confirms +5V supply is present

8. The demonstration code starts(b); the user LEDs LE1 and LE2 are blinking and they are

showing the microcontroller is working properly.

The jumper configuration can be modified to configure the peripherals or to enable

functions. Before modifying the HW or any jumper, it is mandatory to switch off the board.

The configuration will be valid after the board is switched on.

a. The mains adapter is not included in the kit.

b. The demo software has been loaded during the test board procedure

How to connect SPC564A-DISP to a programmer/debugger AN4424

4/7 DocID025693 Rev 2

2 How to connect SPC564A-DISP to a

programmer/debugger

The following procedure describes how to connect and flash the microcontroller to a

programmer/debugger.

2.1 How to connect an adapter to the JTAG connector

The following procedure describes how to connect to, flash and debug the microcontroller

using the JTAG. The procedure describes how to connect the PLS USB-JTAG adapter.

1. Turn off the board (Switch S4=”OFF”)

2. Connect the USB cable to the adapter.

3. Plug the USB cable to the PC (port USB 2.0 or higher).

4. Plug the adapter 14pins female connector (2x7pin) in JP22 connector.

5. Turn on the board (Switch S4=”ON”).

6. The board is ready to be programmed with the user software.

DocID025693 Rev 2 5/7

AN4424 General handling precautions

Appendix A General handling precautions

The following precautions are recommended when using the SPC564A-DISP board:

Do not modify or manipulate the board when the DC supply is connected to the board.

Any equipment or tool used for any manipulation of the semiconductor devices or

board modification should be shielded and connected to ground.

The connectors and cables should be plugged and removed when the board is off.

Do not supply the board with a DC source higher than 5V or with reverse polarity.

It is recommended to use antistatic tools.

Revision history AN4424

6/7 DocID025693 Rev 2

Revision history

Table 1. Revision history

Date Revision Changes

12-Dec-2013 1 Initial release.

08-Aug-2017 2 Delete section 2.2 How to develop, program and

compile a project using SPC5studio and Appendix B

Reference document.

DocID025693 Rev 2 7/7

AN4424

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and

improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on

ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order

acknowledgement.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or

the design of Purchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST SPC58NHADPT386S Bedienungsanleitung

ST SPC5-UDESTK Bedienungsanleitung

ST STEVAL-BLUEPLUG1 Bedienungsanleitung

ST STEVAL-MKI019V1 Bedienungsanleitung

ST STEVAL-OET001V1 Bedienungsanleitung

ST AEK-MOT-TK200G1 Bedienungsanleitung

ST L5965 Bedienungsanleitung

ST UM1789 Bedienungsanleitung

ST STM32G0C1E-EV Bedienungsanleitung

ST EVALST-3PHISOSD Bedienungsanleitung

ST STEVAL-ISB68WA Bedienungsanleitung

ST EVAL-L99DZ200 Bedienungsanleitung

ST STM32F3DISCOVERY Bedienungsanleitung

ST VM6101 Bedienungsanleitung

ST EVAL-RHRPMPOL01 Bedienungsanleitung

ST STM32L4R9I-EVAL Bedienungsanleitung

ST SPC58XXADPT144S REV.B Bedienungsanleitung

ST STM32F334 Bedienungsanleitung

ST STM32U5 Bedienungsanleitung

ST STM32L152RCT6 Discovery kit Bedienungsanleitung

ST X-NUCLEO-CCA02M1 Bedienungsanleitung

ST STEVAL-ILL009V1 Montage- und Bedienungsanleitung

ST User Manual Bedienungsanleitung

ST STEVAL-BLUEMIC-1 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung