ST STEVAL-ISB042V1 Bedienungsanleitung

Introduction

The STEVAL-ISB042V1 is a 15-watt Qi and 5-watt Airfuel inductive (former PMA) wireless power receiver evaluation board

based on the STWLC33 wireless power receiver solution for the WPC/Airfuel mobile device with dual mode coil.

The board lets you evaluate the STWLC33 capabilities as a Qi/Airfuel inductive receiver as well as its ability to power another Qi

receiver.

The solution is certified in accordance with the extended power profile Qi v1.2 and Airfuel SR1 standard.

The STWLC33 IC is powered by a dual mode Rx coil attached to a 1.5 mm thick plastic fixture.

The STWLC firmware offers users the flexibility to modify parameters and settings to ensure proper integration of the STWLC33

device with the final application.

The layout is based on a cost-effective 4-layer PCB.

Figure 1. STEVAL-ISB042V1 evaluation board

Getting started with the dual mode wireless power evaluation board for Qi and Air-

fuel inductive receiver and Qi-based transmitter with STWLC33

UM2289

User manual

UM2289 - Rev 2 - December 2017

For further information contact your local STMicroelectronics sales office.

www.st.com/

1 Getting started

1.1 Board configuration and test points

• P3 solder bridge:

– open = I²C bus and INT pin pull-up voltage provided externally via J5 header

– shorted = I²C bus and INT pin pull-up voltage provided by STWLC33 (do not connect any load/source

to J5 header)

• P9 solder bridge:

– open = USB port acts as unknown (D+/D- floating)

– shorted = USB port acts as a dedicated charging port (shorted D+/D-)

• J3 testpoint header:

– VRECT rectified voltage

• J4 testpoint header:

– selectable user functions (GPIO0, GPIO1, GPIO2, GPIO4)

– GPIO3 – do not connect any load during startup

– INT – open drain interrupt output (active low)

– EN – enable input (active low), pull on-board R4 down

1.2 Receiver mode

The easiest way to test the STEVAL-ISB042V1 evaluation board in receiver mode is to connect the load to J2

header or, optionally, to J1 USB connector and place it on the transmitter surface.

J1 and J2 connectors are essentially different connectors for the same output node.

UM2289

Getting started

UM2289 - Rev 2 page 2/26

Figure 2. STEVAL-ISB042V1 evaluation board: receiver mode

D6 indication LED lights up when the receiver enters the Power Transfer phase.

1.3 Transmitter mode

To test the board in Tx mode, you must provide a 5 V power supply to the J2 header (ensure STWLC33 is not

operating in Rx mode power transfer) and switch STWLC33 to Tx mode over I²C interface (J8 header).

Procedure Step 1. Connect the bundled USB to the I²C bridge.

UM2289

Transmitter mode

UM2289 - Rev 2 page 3/26

Figure 3. STEVAL-ISB042V1 evaluation board: transmitter mode

Step 2. Use the PC GUI application.

Step 3. Connect the I²C bridge.

Step 4. Switch to TX mode tab.

Step 5. Click Load binary image button.

Step 6. Select the GUI STWLC33_TxMode_RAM_binary.bin file.

Figure 4. STEVAL-ISB042V1 GUI Tx mode tab

Step 7. Verify the result by checking the operation mode.

If the label indicates Transmitter mode, the kit is ready and a receiver can be placed on the coil sur-

face.

Note: The coil used in the kit is a Qi/PMA receiver coil. Using this coil for transmitter mode leads to many compromis-

es and not all Qi certified receivers will work with this kit. For the Tx mode evaluation we recommend to use the

STEVAL-ISB043V1 wearable receiver kit as a receiver.

UM2289

Transmitter mode

UM2289 - Rev 2 page 4/26

Figure 5. STEVAL-ISB042V1 GUI operation mode

1.4 STWLC33 NVM configuration

The STWLC33 NVM configuration is the same default configuration as in STWLC33 samples (see STWLC33 da-

tasheet).

1.4.1 Board overview

The STEVAL-ISB042V1 evaluation board default configuration has good performance.

The board features:

• STWLC33 evaluation board with Würth Elektronik dual mode coil (760308102207)

• Qi 1.2 compliant, supporting extended power profile: up to 15 W/10 V maximum output power

• Backward compatible with Qi baseline power profile: up to 5 W/5 V maximum output power

• PMA-SR1 (AirFuel inductive) compliant: 5 W/5.6 V maximum output power

• Transmitter function based on Qi protocol to charge wearable devices using the same Rx coil (up to 3 W

power)

• Total system efficiency up to 80%

• Configurable GPIOs for status indication

• I²C interface for communication with the host system

• Foreign object detection (FOD)

• Complete kit (IC, firmware)

• RoHS compliant

1.5 GUI: I²C register access

Most fields in the GUI application correspond to a single I²C register.(For further details, see STWLC33 datasheet

on www.st.com.)

Many registers are accessible in receiver or transmitter mode only.

Before accessing the registers, you must check the actual operation mode in the Sys_Op_Mode register.

1.5.1 Rx mode registers

The Registers tab contains three sub-tabs related to Rx mode I²C register controls.

Through the Interrupt registers sub-tab, you can monitor the following registers:

• Status_Rx

• INT_Rx

• INT_Enable_Rx

• INT_Clear_Rx

The GUI directly reads or writes the target register.

The Interrupt clear button first writes the INT_Clear_Rx register and then writes 1 in the Clr_Int bit in Com

UM2289

STWLC33 NVM configuration

UM2289 - Rev 2 page 5/26

Figure 6. GUI Rx mode: Interrupt registers sub-tab

The Setup and measurement registers sub-tab controls registers and measurement values.

VOUT_set or ILIM_set modifications are immediate.

The default values are loaded automatically from NVM after wireless operating standard detection.

Important: Refer to 2 Configuration guidelines before changing the values.

The Power transfer termination consists of two steps:

• writing the EPT register;

• writing 1 in the S_EPT bit in Com register.

AD conversion results provide immediate VRECT and VOUT voltages as well as die temperature and output cur-

rent during power transfer.

RXID and PRMC_ID registers become active after wireless standard detection and provide an easy-to-read self-

ID (either Qi ID or PMA ID).

If the STWLC33 receiver is placed on a PMA pad that supports advertising, the advertising ID is captured and can

be read through PMA ADV registers.

UM2289

GUI: I²C register access

UM2289 - Rev 2 page 6/26

Figure 7. GUI Rx mode: Setup and measurement registers sub-tab

The Qi – Proprietary packets sub-tab allows sending any Qi packet and (in Qi 1.2 only) receive the response

from the transmitter (both pattern type or data type responses are supported).

Figure 8. GUI Rx mode: Qi – Proprietary packets sub-tab

1.5.2 Tx mode registers

After entering the mode as described in 1.3 Transmitter mode, the TX mode tab lets you monitor the following

registers:

• Status_Tx

• INT_Tx

• INT_Enable_Tx

• INT_Clear_Tx

The GUI directly reads or writes the target register.

UM2289

GUI: I²C register access

UM2289 - Rev 2 page 7/26

The Interrupt clear button first writes the INT_Clear_Tx register and then writes 1 in the Clr_Int bit in Com reg-

ister.

Tx frequency setup allows modifying the regulation control algorithm minimum and maximum frequency and the

starting ping frequency.

Note: The optimal ping frequency for the STEVAL-ISB042V1 evaluation board is approximately 130 kHz.

ASK demodulation thresholds parameter defines the ASK receiver sensitivity.

Figure 9. GUI Rx mode: TX mode tab

1.6 GUI: NVM configuration access

1.6.1 Qi NVM configuration

The Qi configuration tab contains manufacturer and device identifiers sent over the Qi protocol.

The tab contains also default values for the VOUT voltage, Input current limit and Interrupt enable registers

which can be configured separately for baseline power profile (BPP) operation and for extended power profile

(EPP). BPP values are loaded in the registers and subsequently updated if EPP is negotiated.

STWLC33 automatically terminates the power transfer if the load is below a certain threshold for a certain period

of time. By default, this feature is eliminated by setting the lowest possible current and the longest possible time.

Note: Qi specification does not require this feature.

To maintain the Qi foreign object detection feature accurate, you must provide the correct values representing the

coil parameters and the mechanical setup.

The evaluation kit contains components with the correct values to be used.

But, if, for example, the coil is replaced by another type of coil, you must update the following parameters:

•FOD_A

•FOD_B (different values for BPP and EPP)

•FOD_C (same value for BPP and EPP)

•Reference quality factor (for EPP only)

UM2289

GUI: NVM configuration access

UM2289 - Rev 2 page 8/26

Figure 10. GUI: Qi configuration tab

1.6.2 PMA NVM configuration

The PMA configuration tab contains the RXID identifier sent over the PMA protocol.

The tab contains also default values for the VOUT voltage, Input current limit and Interrupt enable registers.

The PMA specification requires that the receiver automatically terminates the power transfer if the load is below a

certain threshold for a certain period of time.

If the power transfer termination is controlled by the host system, the STWLC33 feature can be eliminated (by

setting zero current and maximum possible time).

Figure 11. GUI: PMA configuration tab

1.6.3 Platform NVM configuration

This tab allows assigning GPIO functions related to Rx mode only.

UM2289

GUI: NVM configuration access

UM2289 - Rev 2 page 9/26

In Tx mode, all the pins are inputs with no function.

In the STEVAL-ISB042V1 evaluation board, the LED diode (D6) is controlled by GPIO2 pin.

Figure 12. GUI: platform configuration tab

1.6.4 Generic load/save NVM access

The NVM tab allows the backup of the current NVM configuration into a file or loading a new one from a file.

Figure 13. GUI: NVM tab

UM2289

GUI: NVM configuration access

UM2289 - Rev 2 page 10/26

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST STEVAL-MKI019V1 Bedienungsanleitung

ST STEVAL-SPIN3202 Bedienungsanleitung

ST STEVAL-PCC008V1 Bedienungsanleitung

ST STM8/128-EVAL Bedienungsanleitung

ST STEVAL-AKI002V1 Bedienungsanleitung

ST STEVAL-ISW001V1 Bedienungsanleitung

ST STA304 Bedienungsanleitung

ST STA333ML Montage- und Bedienungsanleitung

ST STEVAL-SPIN3202 Bedienungsanleitung

ST STM32L4R9I-EVAL Bedienungsanleitung

ST STEVAL-SP1ML915 Bedienungsanleitung

ST SPC58XXADPT64S Bedienungsanleitung

ST STM8L1528-EVAL Bedienungsanleitung

ST STEVAL-IHM022V1 Bedienungsanleitung

ST NUCLEO-F207ZG Bedienungsanleitung

ST STM32756G-EVAL Bedienungsanleitung

ST ST9 EPB Bedienungsanleitung

ST SPC563M64CAL144 Bedienungsanleitung

ST STEVAL-BTDP1 Bedienungsanleitung

ST STM32100B-EVAL Bedienungsanleitung

ST NUCLEO-G070RB Bedienungsanleitung

ST STEVAL-PCC001V1 Bedienungsanleitung

ST STM32 Nucleo-64-P Series Bedienungsanleitung

ST STEVAL-IPP003V1 Kurzanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung