ST STM32MP157D-EV1 Bedienungsanleitung

Introduction

The STM32MP157F-EV1 and STM32MP157D-EV1 Evaluation boards (STM32MP157x-EV1) are designed as complete

demonstration and development platforms for STMicroelectronics Arm®-based dual Cortex®‑A7 32 bits and Cortex®‑M4 32

bits MPUs in the STM32MP1 Series. They leverage the capabilities of increased-frequency 800 MHz STM32MP1 Series

microprocessors for the user to develop applications, using STM32 MPU OpenSTLinux Distribution software for the main

processor, and STM32CubeMP1 software for the co-processor. They include an ST-LINK embedded debug tool, LEDs, push-

buttons, one joystick, 1-Gbps Ethernet, CAN FD, one USB OTG Micro-AB connector, four USB Host Type-A connectors, LCD

display with touch panel, camera, stereo headset jack with analog microphone input, four digital microphones, one SPDIF

Rx/Tx, smartcard, microSD™ card, and eMMC, NOR and NAND Flash memories.

STM32MP157x-EV1, shown in Figure 1 and Figure 2, is used as the reference design for user application development,

although it is not considered as final application.

To expand the functionality of the STM32MP157F-EV1 and STM32MP157D-EV1 Evaluation boards, two GPIO expansion

connectors are also available for motor control and Raspberry Pi® shields.

An ST-LINK/V2-1 is integrated on the board, as embedded in-circuit debugger and programmer for the STM32 MPU and the

USB Virtual COM port bridge.

Figure 1. STM32MP157x-EV1 top view Figure 2. STM32MP157x-EV1 bottom view

Pictures are not contractual.

Evaluation boards with increased-frequency 800 MHz STM32MP157 MPUs

UM2648

User manual

UM2648 - Rev 2 - November 2020

For further information contact your local STMicroelectronics sales office. www.st.com

1Features

• STM32MP157 Arm®-based dual Cortex®‑A7 800 MHz 32 bits + Cortex®‑M4 32 bits MPU in LFBGA448

package

• ST PMIC STPMIC1

• 2 × 4-Gbit DDR3L, 16 bits, 533 MHz

• 2 × 512-Mbit Quad-SPI Flash memory

• 32-Gbit eMMC v5.0

• 8-Gbit SLC NAND, 8 bits, 8-bit ECC, 4-KB PS

• 1-Gbit/s Ethernet (RGMII) compliant with IEEE-802.3ab

• USB Host 4-port hub

• USB OTG HS

• CAN FD

•5.5" TFT 720×1280 pixels with LED backlight, MIPI DSISM interface, and capacitive touch panel

• SAI audio codec

• 5-megapixel, 8-bit camera

• 4 × ST-MEMS digital microphones

• Smartcard

• microSD™ card

• 2 user LEDs

• 2 user and reset push-buttons, 1 wake-up button

• 4-direction joystick with selection button

• 5 V / 4 A power supply

• Board connectors:

– Ethernet RJ45

– 4 × USB Host Type-A

– USB OTG Micro-AB

– SPDIF RCA input and output

– CAN FD

– Stereo headset jack including analog microphone input

– Audio jack for external speakers

– Motor control

– External I2C

– LTDC

– Trace, JTAG, RS-232

– GPIO expansion connector (Raspberry Pi® shields capability)

– MEMS-microphone daughterboard expansion connector

• On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration capability: Virtual COM port and

debug port

•STM32CubeMP1 and full mainline open-source Linux® STM32 MPU OpenSTLinux Distribution (such as

STM32MP1Starter) software and examples

• Support of a wide choice of Integrated Development Environments (IDEs) including IAR Embedded

Workbench®, MDK-ARM, and STM32CubeIDE

STM32 Arm Cortex MPUs are based on the Arm® Cortex®-A and Cortex®-M processors.

Note: Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.

UM2648

Features

UM2648 - Rev 2 page 2/61

2Ordering information

To order an STM32MP157 Evaluation board, refer to Table 1. Additional information is available from the

datasheet and reference manual of the target STM32.

Table 1. List of available products

Order code Board reference Target STM32 Differentiating feature

STM32MP157D-EV1 • MB1262: mother board

• MB1263: MPU subsystem daughterboard

• MB1230: DSI display board

• MB1379: camera board

STM32MP157DAA1 Basic security

STM32MP157F-EV1 STM32MP157FAA1 Secure Boot and

cryptography

2.1 Codification

The meaning of the codification is explained in Table 2.

Table 2. Codification explanation

STM32MP1XXY-EVZ Description Example: STM32MP157F-EV1

STM32MP1 MPU series in STM32 Arm Cortex MPUs STM32MP1 Series

XX MPU product line in the series STM32MP157

Options:

• D: basic security, 800 MHz increased frequency

• F: Secure Boot, cryptography hardware, 800 MHz

increased frequency

Secure Boot, cryptography

hardware, 800 MHz increased

frequency

EVZ Evaluation board configuration

• EV1: with PMIC PMIC

UM2648

Ordering information

UM2648 - Rev 2 page 3/61

3Development environment

3.1 System requirements

• Windows® OS (7, 8, or 10), Linux® 64-bit, or macOS®

• USB Type-C® to Type-A cable

• USB Type-A or USB Type-C® to Micro-B cable

• USB Type-A or USB Type-C® to Micro-AB cable

Note: macOS® is a trademark of Apple Inc. registered in the U.S. and other countries.

All other trademarks are the property of their respective owners.

3.2 Development toolchains

• IAR Systems - IAR Embedded Workbench®(1)

• Keil® - MDK-ARM(1)

• STMicroelectronics - STM32CubeIDE

• GCC

1. On Windows® only.

3.3 Demonstration software

The STM32 MPU OpenSTLinux Distribution and STM32CubeMP1 base demonstration software is preloaded in

the microSD™ for easy demonstration of the device peripherals in standalone mode. The latest versions of the

demonstration source code and associated documentation can be downloaded from www.st.com.

UM2648

Development environment

UM2648 - Rev 2 page 4/61

4Conventions

Table 3 provides the conventions used for the ON and OFF settings in the present document.

Table 3. ON/OFF convention

Convention Definition

Jumper JPx ON Jumper fitted

Jumper JPx OFF Jumper not fitted

Jumper JPx [1-2] Jumper fitted between Pin 1 and Pin 2

Solder bridge SBx ON SBx connections closed by 0 Ω resistor

Solder bridge SBx OFF SBx connections left open

Resistor Rx ON Resistor soldered

Resistor Rx OFF Resistor not soldered

UM2648

Conventions

UM2648 - Rev 2 page 5/61

5Delivery recommendations

Before the first use, make sure that no damage occurred to the board during shipment and no socketed

components are loose in their sockets or fallen into the plastic bag.

In particular, pay attention to the following components:

1. MB1263 daughterboard connected to the MB1262 mother board

2. microSD card in its MB1263/CN9 receptacle

3. LCD MB1230 daughterboard in MB1262/CN19 DSI connector, and screw, spacer and nut are in place

4. Camera module MB1379 board in MB1262/CN7 connector, and screw, spacer and nut are in place

For product information related to the STM32MP157 microprocessors, visit the www.st.com website.

UM2648

Delivery recommendations

UM2648 - Rev 2 page 6/61

6Hardware layout and configuration

The STM32MP157x-EV1 Evaluation board is designed around the STM32MP157xAA1 target microprocessor in

LFBGA 448-pin package. Figure 3 illustrates the STM32MP157x-EV1 hardware block diagram. Figure 4 shows

the location of main components on the Evaluation board.

UM2648

Hardware layout and configuration

UM2648 - Rev 2 page 7/61

Figure 3. STM32MP157x-EV1 hardware block diagram

STM32MP157xAAx

RTC

32 kHz crystal

Capacitive

touch screen

USB OTG Micro-AB USB

OTG HS

5.5" TFT 720x1280

USB

Host HS

USB Hub

4x USB Type-A

microSD™ card

connector

SDMMC

HSI

I2C

GPIO

2 user LEDs

2 user buttons

1 reset button

Smartcard

connector

Smartcard

SAI Audio codec

STPMIC1

5V_VIN

24 MHz crystal

GPIO 40-pin

connector

GPIOs

DDR3L DDR

LTDC LTDC connector

DSI

eMMC SDMMC

NAND FMC

Quad-SPI NOR

Flash Quad-SPI

Gigabit Ethernet RGMII DFSDM MEMS microphones

SPDIF

Tx/Rx SPDIF Tx/Rx

DCMI Camera

CAN FD

CAN FD connector

UART

RS-232 DB9

connector

JTAG/

SWD

ST-LINK/V2-1

USB Micro-B

Motor-control

connector

Shared

GPIOs

I2C

ADC/DAC ADC/DAC

connector

MICTOR-38

connector ETM

JTAG connector

Wake-up button

MFX I/O expander

Joystick

Stereo Jack

Line Out / MIC_IN

I2CI2C_EXT connector

UM2648

Hardware layout and configuration

UM2648 - Rev 2 page 8/61

Figure 4. STM32MP157x-EV1 board overview

Note: Numbers in yellow refer to positions explained in Table 4, Table 5, and Table 6.

UM2648

Hardware layout and configuration

UM2648 - Rev 2 page 9/61

Table 4. STM32MP157x-EV1 overview

Position Description

1 MB1262 mother board

2 MB1263 daughterboard

3MB1230 DSI (MIPI® standard) 720p display

4 MB1379 daughterboard camera

5microSD™ card

Table 5. MB1263 daughterboard overview

Position Description Position Description

50 (B1) Reset button 59 (CN1) MB1263 power 5 V-3 A

51 (LD2) User LED (red) 60 (SW1) Boot mode selection

52 (B2) User button (PA13) 61 (U3) PMIC (STPMIC1A)

53 (LD3) User LED (green) 62 (LD6) ST-LINK LED (bicolor)

54 (B3) User button (PA14) 63 (CN4) USB Micro-B (ST-LINK/V2-1)

55 (LD5) User LED (blue) 64 (U4) STM32MP157xAA1 LFBGA448

56 (LD4) User LED (orange) 65 (U5) eMMC

57 (B4) Wake-up button 66 (U6/U7) 2 x DDR3L 16 bits

58 (LD1) Power LED (green) 67 (µSD)microSD™ 3.0 card (back side slot)

Table 6. MB1262 mother board overview

Position Description Position Description

10 (CN3) Ethernet 11 (CN8) Microphone MEMS daughterboard connector

12 (CN4) Speaker audio output 13 (CN5) Headset audio output

14 (U8) Audio codec (Wolfson WM8994) 15 (CN1) SPDIF RX

16 (CN2) SPDIF TX 17 (U5) Smartcard (back side slot)

18 (LD1) Ethernet LED (green) 19 (CN6) Ethernet daughterboard connector

20 (U10) Trace connector 21 (CN11)LTDC LCD TFT display controller (STM32

specific) connector

22 (CN12) RS-232 (UART4) 23 (CN13) External E2P connector

24 (CN16) USB Micro-AB (USB OTG) 25 (LD2) USB OTG LED (green)

26 (LD3) USB Type-A port LED (red) 27 (CN17) MFX header 4 pins

28 (CN14) JTAG connector 29 (CN15) CAN FD

30 (CN18) 2 USB Type-A port (host) 31 (CN20) 2 USB Type-A port (host)

32 (B2) Reset button 33 (B1) Joystick

34 (CN22) Motor control connector 35 (CN21) GPIO expansion connector

4 (CN7) Camera sensor connector - -

UM2648

Hardware layout and configuration

UM2648 - Rev 2 page 10/61

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST EVAL-L9001 Bedienungsanleitung

ST EVALST-3PHISOSD Bedienungsanleitung

ST STSW-STUSB002 Bedienungsanleitung

ST STM8S Bedienungsanleitung

ST UM0804 Bedienungsanleitung

ST STM32100B-EVAL Bedienungsanleitung

ST STM32 Nucleo Montage- und Bedienungsanleitung

ST STEVAL-LVLP01 Bedienungsanleitung

ST STM3220G-EVAL Bedienungsanleitung

ST STM32MP157 Series Bedienungsanleitung

ST STEVAL-OET001V1 Bedienungsanleitung

ST UM1932 Bedienungsanleitung

ST L9678-S-EVB Bedienungsanleitung

ST STR730-EVAL Bedienungsanleitung

ST SPC5-UDESTK Bedienungsanleitung

ST EVAL-L99H02XP Bedienungsanleitung

ST SPC572LADPT80S Bedienungsanleitung

ST UM2163 Bedienungsanleitung

ST STLINK-V3SET Bedienungsanleitung

ST UM2248 Bedienungsanleitung

ST STM32G4 Nucleo-64 Bedienungsanleitung

ST STEVAL-ILH007V1 Bedienungsanleitung

ST STM32H747I-DISCO Bedienungsanleitung

ST NUCLEO-F411RE Handbuch

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung