Stabila LAR-200 Bedienungsanleitung

SP1: vertical beam emission aperture

SP2: rotation beam emission aperture

ON/OFF switch

Permanent adjustment On/Off selector switch

LEDs for displaying:

Red LED: battery voltage and overheat

Shock protection

5/8" threaded connector for tripod

Battery compartment cover

0049 / 63 46 / 3 09-0

Main components

The STABILA LAR-200 rotation laser is an easy to operate rotation laser for horizontal

levelling and plumb lines in a sealed housing ( IP65). It is self-levelling in a range of

± 5°. The laser beam can be received at distances of up to 150 m with the use of a

receiver, even when it is no longer visible to the naked eye.

We have endeavoured to explain the unit's handling and functioning in as clear

and comprehensible manner as possible. If, however, you still have any unanswered

questions, we should be pleased to provide advice over the telephone at any time

on the following telephone number:

Operating instructions

Splitter pentaprism SP:

(4)

4 markings to create a plumb-line laser function

(1)

(3)

(2)

(5a)

(5b)

(6)

(7)

(8)

(9)

(10)

Housing: hoseproofed sealings and dustprotected acc. to standard IP65

Green LED: Operating mode ON or READY / OK

Recycling programme for our EU customers:

In accordance with the WEEE regulations, STABILA provides a disposal

programme for electronic products at the end of their service life.

For more details, please contact:

www.STABILA.de / Recycling

or:

0049 / 6346 / 309-0

Do not submerge the laser !

Commissioning

- Automatic mode with height of tool alert function

For safety reasons, the rotation laser always switches itself off all when it is

switched on in this operating mode!

The unit can be switched on by briefly tapping button (3). Automatic levelling starts

immediately. The green LED (5b) lights up and the LED (4) flashes. The splitter pen-

taprism begins to rotate and the laser beam comes on. After automatic levelling,

you have approximately 30 seconds in which to set the laser unit in the desired

position, e.g. to adjust its height, set it on a tripod, etc.

During this time, minor discrepancies from the horizontal are ironed out. Then the

laser unit switches to monitored Automatic mode and the LED (4) goes out.

Operating modes:

Main applications:

Levelling

Set the unit on a firm base or a tripod.

Tip: It is useful to set up the rotation laser centrally to

the subsequent measurement points.

Pressing the button (3), switches the rotation laser ON

and it starts to level itself automatically. Once levelling

is complete, the laser begins to rotate. Depending on

the brightness of the ambient light, you can either use

the laser beam, if easily visible, for marking directly

(always ensure that you mark the centre of the laser

beam) or the beam can be received via the receiver.

Please note that the centre of laser dot is marked!

NB:

In Class II laser equipment, your eyes

are protected from accidental, short-

term exposure to the laser beam by

the lid-closing reflex and/or the reflex

reaction to turn one's head. This

equipment can therefore be used

without additional protective measu-

res. Nevertheless, you should not look

directly into the laser beam. The laser goggles enclosed with these

units are not safety goggles. They are desi-

gned to make the laser light easier to see.

Do not let the unit fall into children's

hands!

EN 60825-1 : 03 10

Automatic mode with subsequent readjustment

In many operating conditions (e.g. on strongly vibrating surfaces), it is useful for

the rotation laser to level itself constantly to eliminate any discrepancies that may

arise. After switching it on with button (3), the unit can be switched to this mode by

pressing button (4). The red LED (4) indicates that this mode is active.

Minor discrepancies from the horizontal (from minor tremors) are compensated for.

If these disruptive influences are too great, rotation stops, the laser beam switches

off and the laser unit levels itself again automatically. Once re-levelling is comple-

te, the splitter Pentaprism starts to rotate again.

Height of tool alert function

Minor tremors or vibrations are automatically compensated for only up to a set

threshold. If these disruptive influences are greater than this, the height of tool

alert function engages and rotation stops. The laser beam switches off and the

LED (4) flashes. You must switch the laser unit off using button (3) and then switch it

on again.

Disruptive influences that can lead to adjustment of the precise alignment and the

laser beam's setting do not therefore go unnoticed. When there are disruptive

influences present, the height of tool alert function requires the laser to be checked

and/or reset to the desired position.

Use as a Plumb-line Laser

The laser can be aligned precisely on a marked cross

using the 4 markings (9) on the base to transfer a

plumbline from the floor marking to the ceiling. The

point where the cross intersects corresponds to the

SP1 vertical laser emitter.

A correct result can only be obtained in Automatic

mode with the unit set on a level surface!

The LAR-200 rotation laser has been designed for building site use and leaves our

factory perfectly calibrated. As with any precision instrument, however, its calibra-

tion must be regularly checked. The unit should be checked before starting any

new tasks, particularly when the unit has been exposed to strong vibrations. After

an impact, the unit should be checked throughout its whole self-levelling range.

Checking the calibration

Horizontal checking

6. Repeat steps 4 and 5 to obtain Points 3 and 4.

Mark the position of the visible laser dot on the wall (Point 2).

Mark the position of the visible laser dot on the wall - Measurement 1 (Point 1).

Because the diameter of the beam depends on the distance, you must always

only use the centre of the dot!

Switch the unit on (button 3) and wait for it to level automatically.

Turn the complete unit 90° without altering the height of the laser

(i.e. the tripod must not be altered). Let the unit level automatically again.

If the difference between the 4 control points is less than 1/16" at 25ft

(1mm at 5m) distance and 1/8" at 50ft (2 mm at 10m) distance the permissible

tolerance of ± 1/8" over 100ft (± 0.1 mm/m) is being maintained.

Points 1 and 3 on the unit's y-axis and points 2 and 4 on the unit's x-axis now

correspond.

Set up the rotation laser on a smooth, level surface or on a tripod 25 ft or 50 ft

/ 5m or 10m from a wall with the front facing the wall.

50ft

max

1/16”

1/8”

25ft

Unfasten the catch on

the battery compartment

cover: remove the cover

and the batteries. Insert

new batteries following

the instructions in the

battery compartment.

Only use 1.5V mono cells

(size D)!

Replacing the batteries

Operating status display and error messages via the LEDs

Illuminated green LED

-> The laser levels itself automatically

-> laser in operation

-> battery voltage very low

-> battery replacement required imminently

-> Battery voltage very low

-> The unit is inclined too much

+ is outside the self-levelling range

+ the laser cannot level itself automatically

Illuminated green LED +

laser beam flashing

Illuminated red LED

Flashing red LED

+ laser beam flashing

-> The unit is inclined too much

+ is outside the self-levelling range

+ the laser cannot level itself automatically

Flashing green LED

+ laser beam flashing

-> The laser levels itself automatically

-> Battery voltage very low

-> Battery replacement required imminently

Illuminated red LED

+ laser beam flashing

Tip:

Remove the batteries if the unit will not be used for a long period !

Mono, D , LR20 7

1. 2.

Subject to technical modifications.

Laser type:

Technical data

Self-levelling range:

Output:

Levelling accuracy:

Batteries:

Operating life:

Operating temperature range:

Storage temperature range:

Red diode laser, wavelength 650 nm

< 1 mW, Laser Class 2 to EN 60825-1:03-10

ca. ± 5°

± 0,1 mm/m or ± 1/8” over 100 ft

2 x 1,5 V Mono cells Alkaline, Size D, LR20

Approx. 120 hours

-10°C to +60°C or 14°F to +140°F

-20 °C to +70 °C or -4°F to +158°F

• Dirty lens glass on the beam emitter detracts from the quality of the beam.

It should be cleaned with a soft cloth.

• Clean the laser unit with a damp cloth. Do not spray or immerse the unit!

Do not use solvents or thinners!

Care and maintenance

The LAR-200 rotation laser must be handled carefully, in the same way as any

precision optical instrument.

Stabila provides a guarantee against deficiencies and faults in the assured characte-

ristics because of material or manufacturing faults for a period of 24 months from

date of purchase. Any faults will be eliminated at Stabila's own discretion either by

repairing or replacing the unit. Stabila accepts no wider claims.

No liability is accepted for any faults due to inappropriate treatment (e.g. damage

caused by the unit falling, operation with the wrong voltage or type of current, use of

unsuitable current supply sources) or for any autonomous changes made to the unit

by the purchaser or a third party.

Also no claims under guarantee are accepted for natural wear and tear or any small

faults that do not significantly affect the unit's operation.

Any guarantee claims must be made via the dealer on the duly completed guarantee

form (see last page) to be returned with the unit.

Guarantee terms and conditions

Andere Handbücher für LAR-200

Inhaltsverzeichnis

Andere Stabila Laser-Nivelliergerät Handbücher

Stabila

Stabila LAPR-150 Bedienungsanleitung

Stabila

Stabila LAR-250 Bedienungsanleitung

Stabila

Stabila LA-5PG Bedienungsanleitung

Stabila

Stabila LAX 300 G Bedienungsanleitung

Stabila

Stabila LA-4P Bedienungsanleitung

Stabila

Stabila Laser LA-P+L Bedienungsanleitung

Stabila

Stabila LA 90L Bedienungsanleitung

Stabila

Stabila LA-5P Bedienungsanleitung

Stabila

Stabila TECH 196-2 Electronic Series Bedienungsanleitung

Stabila

Stabila 196 electronic IP65 Bedienungsanleitung

Stabila

Stabila LAR-250 Bedienungsanleitung

Stabila

Stabila OLS 26 Bedienungsanleitung

Stabila

Stabila Laser LAR 120 G Bedienungsanleitung

Stabila

Stabila Laser LAX 300 Bedienungsanleitung

Stabila

Stabila Laser FLS 90 Bedienungsanleitung

Beliebte Laser-Nivelliergerät Handbücher anderer Marken

Nedo

Nedo ET-5 Bedienungsanleitung

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Bedienungsanleitung

LaserLiner

LaserLiner X2-Laser Bedienungsanleitung

Spectra

Spectra LL300N Bedienungsanleitung

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Bedienungsanleitung

Nedo

Nedo Crossliner 4 Bedienungsanleitung

Lasertec

Lasertec FX360G Bedienungsanleitung

Flex

Flex ALC 8 Bedienungsanleitung

Black & Decker

Black & Decker LZR5 Bedienungsanleitung

Johnson

Johnson 40-6692 Bedienungsanleitung

Cocraft

Cocraft HL 20-SG Bedienungsanleitung

Zircon

Zircon iLine Bedienungsanleitung

HWH

HWH 310 SERIES Bedienungsanleitung

Leica

Leica iCON robot 60 Bedienungsanleitung

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Bedienungsanleitung

LaserLiner

LaserLiner ActiveFinder XP Bedienungsanleitung

DeWalt

DeWalt DW082 Bedienungsanleitung

imex

imex EL20 Bedienungsanleitung