Stagg TAGGER 30 Bedienungsanleitung

USER MANUAL

TAGGER 30

SLI-MHBTAGG30

Please read the instructions carefully before use

SAFETY INSTRUCTIONS

Please read the instructions carefully as they include important

information about the installation, operation and maintenance.

• Please keep this user’s guide for future consultation. If you sell the unit to another

user, be sure that they also receive this instruction booklet.

• All fixtures leave the manufacturer intact. Please note that any damages incurred

by the user is not covered by the guarantee.

• Unpack and check carefully that there is no transportation damage before using the

unit.

• The unit is for indoor use only. Use only in a dry location.

• Use a safety bond when attaching the fixture to a lighting rig. Handle by the

hanging bracket when fixing.

• The unit must be installed in a location with adequate ventilation at least 50 cm

from adjacent surfaces.

• Make sure that no ventilation slot is blocked, otherwise the unit will overheat.

• Before operating, ensure that the voltage and frequency of the power supply match

the power requirements of the unit.

• Make sure all equipment is properly earthed.

• Do not operate the unit if the ambient temperature is higher than 40°C.

• Do not hardwire to any mains dimmer.

• On the first start, there may be some normal operational start-up smell.

• Make sure that there is no flammable material close to the unit while operating, as

it is a fire hazard.

• Examine power wires carefully and replace immediately if there is any damage.

• Never run on for a long time lest shortening lifespan. Avoid any inflammable liquids,

water or metal objects entering the unit. In case it happens, cut off the mains power

immediately.

• Do not operate in a dirty or dusty environment. Clean fixtures regularly.

• Do not allow children unsupervised to operate the fixture.

• Do not touch any wire during operation as there might be a hazard of electric

shock.

• Avoid placing power wires next to other cables.

• Disconnect the mains power before replacing or servicing the fuses.

• Replace fuse only with the same type.

• In the event of a serious operating problem, stop using the unit immediately.

• Never turn on and off the unit time after time.

• The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

• Do not open the unit as there is no user serviceable part inside.

• Never try to repair the unit by yourself. Repairs carried out by unskilled people can

lead to damage or malfunction. Please contact the nearest authorized technical

assistance centre.

• Disconnect the mains power if the fixture is not used for a long time.

• Use the original packaging to transport regarding any warranty issue.

• Do not look directly at the LED light beam while the fixture is on.

• Do not connect more than 7 units to the same power source.

INSTALLATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that

the structure to which you are attaching the unit is secure and able to support 10 times

the unit’s weight. Also, always use a safety cable that can hold 12 times the unit’s

weight when installing the fixture.

The equipment must be fixed in an appropriate place by professionals. Keep it out of

the reach of unqualified people.

TECHNICAL SPECIFICATIONS

Gobo moving head with 35-watt COB LED 7 colours, 7 gobos.

- LED: 35W white LED

- 540° pan, 230° tilt

-Beam angle: 13°

- Colour wheel: 7 colours + white

- 7 fixed gobo's + open with shake

- Manual focus

- protocol: DMX-512 : 9 or 11 Channels

- Strobe: 0-10Hz

- Control Modes: DMX, automatic, sound mode or Manual Setup

- Display: 4 Digit

- DMX input & output: 3-pin XLR connectors

- Power input: IEC

-Included: Hanging bracket (truss- or other clamp not included)

- Power consumption: 35W (max)

- For indoor use only

- Weight: 3kg (6.6lb)

- Size: 290 x 260 x 210 mm (11.4 x 10,2 x 8.3“)

SETTING UP THE DEVICE

DMX Mode

With the menu button, select the DMX mode (ADDR) and press the enter key to

confirm. Then use the up and down buttons to choose the desired DMX channel (1 –

512) and press the enter key to confirm. Press the menu button to return to the main

menu.

With the menu button, select the personality mode (CHND) and press enter. This

fixture works with 9 and 11 DMX channels. Select the desired one and press enter.

Channel

Range

Function

CH1

0-255

Pan

CH2

0-255

Tilt

CH3

0-159

Colour change

160-255

Colour change slow to fast

CH4

0-63

Fix gobo

64-127

Gobo shake

128-255

Gobo change slow to fast

CH5

0-255

Strobe

CH6

0-255

Dimmer

CH7

0-255

Movement speed

CH8

0-255

Auto. Mode

CH9

250-255

Reset (5 sec. delay)

Channel

Range

Function

CH1

0-255

Pan

CH2

0-255

Pan Fine

CH3

0-255

Tilt

CH4

0-255

Tilt Fine

CH5

0-159

Colour change

160-255

Colour change slow to fast

CH6

0-63

Fix gobo

64-127

Gobo shake

128-255

Gobo change slow to fast

CH7

0-255

Strobe

CH8

0-255

Dimmer

CH9

0-255

Movement speed

CH10

0-59

Off

60-84

Auto mode 1

85-109

Auto mode 2

110-134

Auto mode 3

135-159

Sound mode 1

160-184

Sound mode 2

185-209

Sound mode 3

210-234

Sound mode 4

235-255

Sound mode 5

CH11

250-255

Reset (5 sec. delay)

Master/Slave mode

With the menu button, select the Master and Slave mode (SLND) and press enter.

Then use the “up” and “down” buttons to select between Master (MAST), Slave 1

(SL.1) and Slave 2 (SL.2).

Thanks to this mode, you can connect several Tagger 30 in a daisy chain and make

a nice lightshow. All the units will play in the same rhythm. To do so, put the first light

in your chain in “master” mode. Put the other ones in Slave 1 or 2. Slave 1 and 2 will

react in a different way to do a more complex lightshow.

Automatic mode

With the menu button, select the automatic mode (SHND) and press the enter key to

confirm. Then use the up and down buttons to choose the desired mode from SH.0

to SH.3.

Sound Mode

With the menu button, select the Sound mode (SOUD) and press the enter key to

confirm. Then use the up and down buttons to select if “YES” or “NO” the automatic

mode need to be sound controlled.

Sound sensibility

With the menu button, select the sound sensibility setting (SENS) and press the

enter key to confirm. Then use the up and down buttons to choose the desired

sensibility of the internal microphone from 000% to 100%.

Blind Menu

With the menu button, select the automatic mode (BLND) and press the enter key to

confirm. Then use the up and down buttons to choose the best action to do if the

DMX signal is lost:

-bLAc: Switch the unit in standby mode. Dimmer at 0.

-Auto: Switch the unit into automatic mode.

-Soun: Switch the unit in automatic mode with sound activated sequences.

-HoLd: The unit freeze with the last received parameters.

Other Settings

Use the menu button to change some parameters:

-Led: “On” or “Off”. On “Off” position, the display automatically shut down after 8

seconds.

-Disp: Let you define if the display has to be read upside down. For example, if you

hang it to a truss.

-rPAN: Reverse horizontal movements.

rTILT: Reverse vertical movements.

Rset: Reset all factory settings.

DMX512 CONNECTIONS

The DMX512 is widely used in intelligent lighting control, with a maximum of 512

channels.

Warning

To avoid signal transmission problems and interferences when using fixtures in

chain, use a Stagg N-series professional 3-pin DMX terminator (resistance: 120

ohms; pin2: DMX-; pin3:DMX+).

FIXTURE CLEANING

An internal cleaning must be carried out periodically to optimize the light output. The

cleaning frequency depends on the environment in which the fixture operates: A

damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt

on the fixture’s optics. Clean the fixture with a soft cloth and normal glass cleaning

fluid. Always dry the parts carefully. Clean the internal optics at least every 30 days.

Clean the external optics at least every 20 days.

For more info and the latest product updates:

staggmusic.com

EMD Music S.A.

Boulevard Général Wahis 16A

1030 Brussels

Belgium

05/2018

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Stagg Beleuchtungsausrüstung Handbücher

Stagg

Stagg EcoParXS Bedienungsanleitung

Stagg

Stagg FlatPar 4 Bedienungsanleitung

Stagg

Stagg Hyperion 5R Bedienungsanleitung

Stagg

Stagg Ecopar 630 31 Bedienungsanleitung

Stagg

Stagg HEADBANGER10 MK3 Bedienungsanleitung

Stagg

Stagg TRITON SDJ-TRITON Bedienungsanleitung

Stagg

Stagg HeadHunter10 SLI-MHBHH10 Bedienungsanleitung

Stagg

Stagg EcoPar6 Bedienungsanleitung

Stagg

Stagg HEAD BANGER 10 SLI MHW HB10 Bedienungsanleitung

Stagg

Stagg HEADBANGERXT SLI MHW HBXT Bedienungsanleitung

Stagg

Stagg KINGPAR 1 Bedienungsanleitung

Stagg

Stagg SLI-MHBHH10 Bedienungsanleitung

Stagg

Stagg Truss34 Bedienungsanleitung

Stagg

Stagg HYPERNOVA SDJ-HYPERNOV1 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung