Stanley SCH20 Bedienungsanleitung

ENGLISH (Original instructions)

SCH20

SCH201

English Page 4

Françaıs Page 8

ﺔﻴﺑﺮﻌﻟﺍ Page 25

ENGLISH (Original instructions)

Fig. A

ENGLISH (Original instructions)

4 5

Fig. B

Fig. D

Fig. F

Fig. E

Fig. G

Fig. C

ENGLISH (Original instructions)

Intended use

Your Stanley Hammer drill SCH20 has been designed

for drilling in concrete, metal, wood and screwdriving

applications. This tool is intended for professional use.

Safety instructions

General power tool safety warnings

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future

reference.

The term “power tool” in the warnings refers to your

mainsoperated (corded) power tool or battery-operated

(cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose

control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk

of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric

shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b. Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

c. Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invites accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal

injury.

e. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

c. Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

ENGLISH (Original instructions)

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc.

In accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5. Battery tool use and care

a. Recharge only with the charger specified by the

manufacturer. A charger A charger that is suitable for

one type of battery pack may create a risk of fire when

used with another battery pack.

b. Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury and fire.

c. When battery pack is not in use, keep it away from

other metal objects like paper clips, coins, keys,

nails, screws or other small metal objects that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or a fire.

d. Under abusive conditions, liquid may be ejected

from the battery, avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

6. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional Specific Safety Rules for Drill/Drivers

♦Wear ear protectors when impact drilling. Exposure

to noise can cause hearing loss.

♦Use auxiliary handle(s) if supplied with the tool.

Loss of control can cause personal injury.

♦Hold power tool by insulated gripping surfaces

when performing an operation where the cutting

accessory may contact hidden wiring. Cutting

accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

Residual risks.

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks cannot be avoided.

These are:

♦Impairment of hearing.

♦Risk of personal injury due to flying particles.

♦Risk of burns due to accessories becoming hot during

operation.

♦Risk of personal injury due to prolonged use.

Labels on tool

The following pictograms are shown on the tool along

with the date code:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Always wear safety goggles

Always wear safety hearing protection

POSITION OF DATE CODE

The Date Code, which also includes the year of

manufacture, is printed into the housing.

Example:

2015 XX JN

Year of manufacturing

Important Safety Instructions for All Battery

Chargers

SAVE THESE INSTRUCTIONS: This manual contains

important safety and operating instructions for the SC201 /

SC202 battery chargers.

♦Before using charger, read all instructions and

cautionary markings on charger, battery pack, and

product using battery pack.

WARNING: Shock hazard. Do not allow any

liquid to get inside charger. Electric shock may

result.

Caution: Burn hazard. To reduce the risk

of injury, charge only STANLEY rechargeable

batteries. Other types of batteries may burst

causing personal injury and damage.

CAUTION: Children should be supervised to

ensure that they do not play with the appliance.

NOTICE: Under certain conditions, with the

charger plugged in to the power supply, the

charger can be shorted by foreign material.

Foreign materials of a conductive nature such

ENGLISH (Original instructions)

as, but not limited to, grinding dust, metal chips,

steel wool, aluminum foil, or any buildup of

metallic particles should be kept away from

charger cavities. Always unplug the charger

from the power supply when there is no battery

pack in the cavity. Unplug charger before

attempting to clean.

♦DO NOT attempt to charge the battery pack with

any chargers other than the ones in this manual.

The charger and battery pack are specifically designed

to work together.

♦These chargers are not intended for any uses other

than charging STANLEY rechargeable batteries.

Any other uses may result in risk of fire, electric shock

or electrocution.

♦Do not expose charger to rain or snow.

♦Pull by plug rather than cord when disconnecting

charger. This will reduce risk of damage to electric plug

and cord.

♦Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage or stress.

♦Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could

result in risk of fire, electric shock, or electrocution.

♦Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal

heat. Place the charger in a position away from any

heat source. The charger is ventilated through slots in

the top and the bottom of the housing.

♦Do not operate charger with damaged cord or plug

— have them replaced immediately.

♦Do not operate charger if it has received a sharp

blow, been dropped, or otherwise damaged in any

way. Take it to an authorised service centre.

♦Do not disassemble charger; take it to an

authorised service centre when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock, electrocution or fire.

♦In case of damaged power supply cord the supply cord

must be replaced immediately by the manufacturer, its

service agent or similar qualified person to prevent any

hazard.

♦Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk

of electric shock. Removing the battery pack will not

reduce this risk.

♦NEVER attempt to connect 2 chargers together.

♦The charger is designed to operate on standard

household electrical power. Do not attempt to use

it on any other voltage. This does not apply to the

vehicular charger.

SAVE THESE INSTRUCTIONS

Chargers

The SC201/ SC202 accept 18V batteries.

These chargers require no adjustment and are designed to

be as easy as possible to operate.

Charging Procedure (fig. B)

1. Plug the charger into an appropriate outlet before

inserting battery pack.

2. Insert the battery pack (6) into the charger. The red

(charging) light will blink continuously indicating that the

charging process has started.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The pack is fully

charged and may be used at this time or left in the

charger.

Note: To ensure maximum performance and life of Li-Ion

batteries, charge the battery pack fully before first use.

Charging Process

Refer the tables below for the state of charge of the battery

pack.

State of charge–SC201/SC202

charging ― ― ― ―

fully charged

hot/cold pack delay ― ― ― │

Hot/Cold Pack Delay

SC201/ SC202

When the charger detects a battery that is hot, it

automatically delays charging until the battery has cooled.

When the charger detects a battery that is cold, it

automatically delays charging until the battery has warmed.

The red light will continue to blink, but a yellow indicator

light will be illuminated during this operation. Once the

battery has cooled, the yellow light will turn off and the

charger will resume the charging procedure.

Stanley Li-Ion tools are designed with an Electronic

Protection System that will protect the battery against

overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the Li-Ion

battery on the charger until it is fully charged.

Li-Ion BATTERY PACKS ONLY

Li-Ion batteries are designed with an Electronic Protection

System that will protect the battery against overloading,

overheating or deep discharge.

ENGLISH (Original instructions)

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the Li-Ion

battery on the charger until it is fully charged.

Important Safety Instructions for All Battery

Packs

When ordering replacement battery packs, be sure to

include catalog number and voltage.

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the safety

instructions below. Then follow charging procedures

outlined.

READ ALL INSTRUCTIONS

♦Do not charge or use battery in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the

battery from the charger may ignite the dust or fumes.

♦Never force battery pack into charger. Do not

modify battery pack in any way to fit into a non-

compatible charger as battery pack may rupture

causing serious personal injury.

♦Charge the battery packs only in STANLEY chargers.

♦DO NOT splash or immerse in water or other liquids.

♦Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed40˚C(105˚F)(suchasoutsideshedsor

metal buildings in summer).

WARNING : Never attempt to open the battery

pack for any reason. If battery pack case is

cracked or damaged, do not insert into charger.

Do not crush, drop or damage battery pack.

Do not use a battery pack or charger that has

received a sharp blow, been dropped, run over

or damaged in any way (i.e., pierced with a nail,

hit with a hammer, stepped on). Electric shock or

electrocution may result. Damaged battery packs

should be returned to service centre for recycling.

CAUTION: When not in use, place tool on its

side on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery

pack but may be easily knocked over.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM

ION (Li-ION)

♦Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack

can explode in a fire. Toxic fumes and materials are

created when lithium ion battery packs are burned.

♦If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the

open eye for 15 minutes or until irritation ceases. If

medical attention is needed, the battery electrolyte is

composed of a mixture of liquid organic carbonates and

lithium salts.

♦Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medical attention.

WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark or flame.

Transportation

STANLEY batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards

which include UN Recommendations on the Transport of

Dangerous Goods; International Air Transport Association

(IATA) Dangerous Goods Regulations, International

Maritime Dangerous Goods (IMDG) Regulations, and

the European Agreement Concerning The International

Carriage of Dangerous Goods by Road (ADR). Lithium-ion

cells and batteries have been tested to section 38.3 of

the UN Recommendations on the Transport of Dangerous

Goods Manual of Tests and Criteria.

In most instances, shipping a STANLEY battery pack will

be excepted from being classified as a fully regulated Class

9 Hazardous material. In general, the two instances that

require shipping Class 9 are:

1. Air shipping more than two STANLEY lithium-ion

battery packs when the package contains only battery

packs (no tools), and

2. Any shipment containing a lithium-ion battery with an

energy rating greater than 100 watt hours (Wh). All

lithium-ion batteries have the watt hour rating marked

on the pack.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper’s responsibility to

consultthe latest regulations for packaging, labeling/

marking and documentation requirements.

Transporting batteries can possibly cause fire if the battery

terminals inadvertently come in contact with conductive

materials. When transporting batteries, make sure that

the battery terminals are protected and well insulated from

materials that could contact them and cause a short circuit.

The information provided in this section of the manual

is provided in good faith and believed to be accurate

at the time the document was created. However, no

warranty, expressed or implied, is given. It is the buyer’s

responsibility to ensure that its activities comply with the

applicable regulations.

ENGLISH (Original instructions)

Storage Recommendations

1. The best storage place is one that is cool and dry

away from direct sunlight and excess heat or cold. For

optimum battery performance and life, store battery

packs at room temperature when not in use.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool, dry place out of the

charger for optimal results.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be recharged

before use.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the

labels on the charger and the battery pack may show the

following pictographs:

Read instruction manual before use.

See Technical Data for charging time.

100%

Battery charging.

100%

Battery charged.

Battery defective.

Hot/cold pack delay.

Do not probe with conductive objects.

Do not charge damaged battery packs.

Do not expose to water.

Have defective cords replaced immediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indoor use.

Discard the battery pack with due care for the

environment.

SC201

Charge STANLEY battery packs only with

designated STANLEY chargers. Charging battery

packs other than the designated STANLEY

batteries with a STANLEY charger may make

them burst or lead to other dangerous situations.

Do not incinerate the battery pack.

Package Contents

The package contains:

1 Hammer drill

1 Charger

2 Batteries (C2/D2) or 1 Battery (C1/D1)

1 Instruction manual

NOTE: Battery packs and chargers are not included with

N-models.

•Check for damage to the tool, parts or accessories which may

have occurred during transport.

• Take the time to thoroughly read and understand this

manual prior to operation.

STORAGE RECOMMENDATIONS

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold.

2. Long storage will not harm the battery pack or charger.

FEATURES (Fig. A)

1. Trigger Switch

2. Forward/Reverse Button

3. Torque Adjust Collar

4. Dual Range Gear Selector

5. Keyless Chuck

6. Battery

7. Battery Release Button

8.LED Work Light

9. Bit Tip Holder

INTENDED USE

This hammer drill is designed for light fastening and drilling

applications.

DO NOT use under wet conditions or in presence of

flammable liquids or gases.

This hammer drill is a professional power tool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

this tool.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

ENGLISH (Original instructions)

mental abilities, or for lack of experience and/or for want

of knowledge or skills unless they are supervised by a

person responsible for their safety. Children should never

be left alone to play with this product.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of your mains.

Your STANLEY charger is double insulated in

accordance with EN 60335; therefore no earth

wire is required.

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the STANLEY

service organisation.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1 mm2; the maximum length is 30

When using a cable reel, always unwind the cable completely.

Assembly and adjustments

WARNING: Prior to assembly and adjustment,

always remove the battery pack. Always switch

off the tool before inserting or removing the

battery pack.

WARNING: Use only STANLEY battery packs

and chargers.

Inserting and Removing the

Battery Pack from the Tool (Fig. B & C)

WARNING: To reduce the risk of serious

personal injury, place the forward/reverse

button in the lock-off position or turn tool off

and disconnect battery pack before making

any adjustments or removing/installing

attachments or accessories. An accidental

start-up can cause injury.

NOTE: Make sure your battery pack (6) is fully charged.

TO INSTALL THE BATTERY PACK INTO THE TOOL

HANDLE

1. Align the battery pack with the rails inside the handle.

2. Slide it firmly into place until you hear the lock snap into

place.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the release button (7) and firmly pull the battery

pack out of the tool handle.

2. Insert battery pack into the charger as described in the

charger section of this manual.

OPERATING INSTRUCTIONS

Safety warnings and instructions: Drills

@WARNING! Before using tool, read all in-

structions and cautionary markings on tool.

@WARNING! Drill may stall (if overloaded or

improperly used) causing a twist. Always

expect the stall. Grip the drill firmly with two

hands to control the twisting action and pre-

vent loss of control which could cause per-

sonal injury. If a stall does occur, release

the trigger immediately and determine the

reason for the stall before re-starting.

Trigger switch & forward/reverse button (Fig. D)

♦The drill is turned ON and OFF by pulling and

releasing the trigger switch (1) shown in Fig. D. The

farther the trigger is depressed, the higher the speed

of the drill.

♦A forward/reverse control button (2) determines the

rotational direction of the tool and also serves as a lock

off button.

♦To select forward rotation, release the trigger switch

and depress the forward/reverse control button on the

right side of the tool.

♦To select reverse, depress the forward/reverse control

button on the left side of the tool.

♦The center position of the control button locks the tool

in the off position. When changing the position of the

control button, be sure the trigger is released.

Adjusting torque control (Fig. E)

This tool is fitted with a torque adjustment collar (3) to

select the operating mode and to set the torque for tight-

ening screws. Large screws and hard workpiece materials

require a higher torque setting than small screws and soft

workpiece materials.

♦For drilling in wood, metal and plastics, set the collar to

the drilling position symbol .

♦For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed

as follows:

♦Set the collar to the lowest torque setting.

ENGLISH (Original instructions)

♦Tighten the first screw.

♦If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

Note: When using the Hammer drill for drilling holes, be

sure that the function collar is set so the figure of the drill

is aligned with the center line on the top of the tool. Failure

to do this will allow the clutch to slip while attempting to drill.

Dual range switch (Fig. F)

♦The dual range feature of your drill allows you to shift

gears for greater versatility.

♦To select low speed, high torque setting (position 1),

turn tool off and permit to stop. Slide gear shifter button

(4) away from the chuck.

♦To select the high speed, low torque setting (position 2),

turn tool off and permit to stop. Slide gear shifter button

back toward the chuck.

♦Note: Do not change gears when tool is running. If you

are having trouble changing gears, make sure that the

dual range gear button is either completely pushed

forward or completely pushed back.

Keyless chuck (Fig. G)

Warning! Make certain the battery pack is

removed to prevent tool actuation before installing

or removing accessories.

To insert a drill bit or other accessory:

1. Grasp the chuck (5) and rotate it in the counterclockwise

direction, as viewed from the chuck end.

2. Insert the bit or other accessory fully into the chuck,

and tighten securely by rotating the chuck in the clockwise

direction as viewed from the chuck end.

@Warning! Do not attempt to tighten or

loosen drill bits (or any other accessory)

by gripping the front part of the chuck

and turning the tool on. Damage to the

chuck and personal injury may occur when

changing accessories.

Screw driving

♦For driving fasteners, the forward/reverse button should

be pushed to the left.

♦Use reverse (button pushed to the right) for removing

fasteners.

Note: When moving from forward to reverse, or vice

versa, always release the trigger switch first.

Drilling

♦Use sharp drill bits only.

♦Support and secure work properly, as instructed in the

Safety Instructions.

♦Use appropriate and required safety equipment, as

instructed in the SafetyInstructions.

♦Secure and maintain work area, as instructed in the

SafetyInstructions.

♦Run the drill very slowly, using light pressure, until the

hole is started enough to keep the drill bit from slipping

out of it.

♦Apply pressure in a straight line with the bit. Use

enough pressure to keep the bit biting but not so much

as to stall the motor or deflect the bit.

♦Hold the drill firmly with two hands, one hand on the

handle, and the other gripping the bottom around the

battery area or the auxillary handle if provided.

♦Do not click the trigger of a stalled drill off and on

in anattempt to start it. Damage to the drill can

result.

♦Minimize stalling on break through by reducing ressure

and slowly drilling through the last part of the hole.

♦Keep the motor running while pulling the bit out of a

drilled hole. This will help reduce jamming.

♦Make sure switch turns drill on and off.

Drilling in Masonry (Fig. E)

1. Turn the collar (3) to the hammer drill symbol.

2. Select the high speed setting by sliding the selector

forward (towards the chuck). Important: Use carbide

tipped or masonry bits only.

3. Drill with just enough force on the hammer to keep

it from bouncing excessively or “rising” off the bit.

Too much force will cause slower drilling speeds,

overheating and lower drilling rate.

4. Drill straight, keeping the bit at a right angle to the

work. Do not exert side pressure on the bit when

drilling as this will cause clogging of the bit flutes and a

slower drilling. When drilling deep holes, if the hammer

speed starts to drop off, pull the bit partially out of the

hole with tool still running to help clear debris from the

hole.

Note: A smooth, even flow of dust from the hole indicates

proper drilling rate speed.

Drilling in wood

Holes in wood can be made with the same twist drill bits

used for metal or with spade bits. These bits should be

sharp and should be pulled out frequently when drilling to

clear chips from the flutes.

Andere Handbücher für SCH20

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Stanley Gleichstromantrieb Handbücher

Stanley

Stanley PD45 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch

Lenze

Lenze 8200 vector Bedienungsanleitung