Stanley NB08PT-18 Bedienungsanleitung

NB08PT-18 Blind nut tool

Battery Power Tool

Accessories

Manual

The information provided may not be reproduced and/or made public in any way and through any means (electronically or mechanically) without

prior explicit and written permission from STANLEY Engineered Fastening. The information provided is based on the data known at the moment of

the introduction of this product. STANLEY Engineered Fastening pursues a policy of continuous product improvement and therefore the products

may be subject to change. The information provided is applicable to the product as delivered by STANLEY Engineered Fastening. Therefore,

STANLEY

Engineered Fastening cannot be held liable for any damage resulting from deviations from the original specifications of the product.

The information available has been composed with the utmost care. However, STANLEY Engineered Fastening will not accept any liability with

respect to any faults in the information nor for the consequences thereof. STANLEY Engineered Fastening will not accept any liability for damage

resulting from activities carried out by third parties. The working names, trade names, registered trademarks, etc. used by STANLEY Engineered

Fastening should not be considered as being free, pursuant to the legislation with respect to the protection of trademarks.

OriginalInstruction

STANLEY Engineered Fastening policy is one of continuous product development and improvement

and we reserve the right to change the specification of any product without prior notice.

Nose Assemblies

Nose equipment varies according to the blind insert nut type being installed. Each nose assembly

represents a unique set of components which can be ordered individually. Component numbers

refer to the illustration below. We recommend maintaining some stock of spares as items will need

regular replacement if worn. Read the Service Manual for nose assembly instructions.

MAIN COMPONENTS LIST

Mandrel

Spin Pull Head Case

Nosepiece

Spin Pull Head

Lock Nut

FR Lever

Nose Housing

Mast Housing

Nose Housing Nut

Nut

Mandrel Lock

*for complete tool explosion and Bill of Material please see service manual

ACCESSORIES CHANGING INSTRUCTIONS

Always wear approved hearing and eye protections at all times when using installation

equipment.

WARNING: Before adjusting tool, always remove the battery pack.

Mounting the mandrel and nosepiece

•Select the correct mandrel (A) and nosepiece (B) for the blind nut (K) to be

installed.

•Loosen the nose housing nut (E), Remove the nose housing (D).

•Press the mandrel lock (F), Loosen and remove the mandrel (A).

•Screw the correct mandrel (A) into Spin Pull Head (H) while pressing the mandrel

lock (F). Lock the mandrel (A)

•Loosen the lock nut (C) and unscrew and remove the nosepiece (B) and Lock nut

(C)

•Screw the Lock nut (C) onto the correct nosepiece (B) and screw the nosepiece (B)

into the nose housing (D) lightly.

•Adjust the position of the nosepiece (B) according to the blind nut (K) to be

installed. The length of mandrel protruding from the top of blind nut (K) to be 0-

0.5mm.

•Tighten the lock nut (C) by a spanner properly.

PLACING SPECIFICATIONS

Nut Type

PLACING CAPACITY

NB08PT-18

M10

Eurosert®

●

Thin Sheet Nutsert®

●

DK/DL

●

Euro Hexsert®/Hexsert®

●

High Strength Hexsert®

●

Squaresert®

●

Standard Nut (Steel)

●

Standard Nut (Aluminum)

●

Standard Nut (Stainless

steel)

●

Closed End Nut

●

Hexagonal Nut

●

All Hexagonal Nut

●

Tetra Nut

●

Knurled Nut

●

Soft Set Nut

●

Slit Nut

●

Pipe Nut

●

HB Bolt

●

HB Bolt for round pipe

●

Note:

Force control can be used for the following sizes only.

Aluminum M6 or more (Except for Slit Nut).

Steel M5 or more.

Stainless steel M5 or more.

MANDREL AND NOSEPIECE

WARNING: When selecting mandrel and nosepiece, always use the compatible parts. Using different

parts may cause nut tightening failure or tool failure.

Note:

1. Refer Table B for Thin sheet Nutsert®.

2. Refer Table C for Thin head Hexsert®.

Table A Mandrel and Nosepiece compatible chart *：Option parts

Nut Size

MANDREL

NOSEPIECE

Part No.

O.D

Part No

I.D

PNT600-01-3*

φ3

PNT600-02-3*

φ4.0

PNT600-01-4

φ4

PNT600-02-4

φ4.5

PNT600-01-5P

φ5

PNT600-02-5

φ5.1

PNT600-01-6P

φ6

PNT600-02-6

φ6.1

PNT600-01-8M

φ8

PNT600-02-8

φ8.1

M10

PNT600-01-10A*

φ10

PNT600-02-10*

φ10.1

6-32 UNC

PNT600-01-632*

φ3.5

PNT600-02-632*

φ3.6

8-32 UNC

PNT600-01-832*

Φ4.1

PNT600-02-832*

Φ4.3

10-24 UNC

PNT600-01-1024*

Φ4.8

PNT600-02-5

φ5.1

10-32 UNF

PNT600-01-1032*

Φ4.8

PNT600-02-5

φ5.1

Table B Thin sheet Nutsert® compatible chart *：Option parts

Nut Size

MANDREL

NOSEPIECE

Part No.

O.D

Part No

I.D

PNT600-01-3*

φ3

TNM00146*

φ3.1

PNT600-01-4P*

φ4

TNM00147*

φ4.1

PNT600-01-5P

φ5

TNM00148*

φ5.1

PNT600-01-6P

φ6

TNM00149*

φ6.1

PNT600-01-8P*

φ8

TNM00150*

φ8.1

Inside Diameter

Outside Diameter

M8×1.0

Inside Diameter

Outside Diameter

M8×1.0

Table C Thin head Hexsert® compatible chart *：Option parts

Nut Size

MANDREL

NOSEPIECE

Part No.

O.D

Part No

I.D

PNT600-01-4P*

φ4

TNM00151*

φ4.1

PNT600-01-5P

φ5

TNM00152*

φ5.1

PNT600-01-6P

φ6

TNM00153*

φ6.1

PNT600-01-8P*

φ8

TNM00150*

φ8.1

MANDREL AND NOSEPIECE

(OPTIONS)

1. Pipe Nut (Made to order)

When fastening the pipe nut SRH-630-191-K2, install the nose assembly for the pipe

nut. The mandrel used is PNT600-01-6P. Please refer to the following list for the

nose assembly components for pipe nuts.

●SRH-630-191-K2

Nose Assembly

TNM00354

SA Mast Housing

TNM00355

SA Nose Housing

TNM00356

Nose Housing

TNM00257

Nose Slider

PNT600-137A

Slider Spring

AN600P-31

Retaining Ring

AN600P-32

Nosepiece

PNT600-02-6NP

Lock Nut

PNT600-03

Hexagon socket button bolt

PNT600-100

Spacer

PNT600-138

Outside Diameter

M8×1.0

Inside Diameter

Lock Nut

Slider Spring

Nosepiece

Retaining Ring

Nose Slicer

Nose Housing

SA Mast Housing

Spacer

Button Head Cap Screw

2. Pipe HB Bolt (Made to order)

When fastening pipe HB bolts, install the pipe HB nose assembly. Change the

mandrel attached to the tool to the socket that comes with the nose assembly.

Please refer to the following list for each nose assembly component.

●SRB-630-480LF-K2-180L

Nose Assembly

TNM00358

SA Mast Housing

TNM00355

SA Nose Housing

TNM00359

Nose Housing

TNM00258

Nose Slider

TP134-080

Slider Spring

AN600P-31

Retaining Ring

AN600P-32

Nosepiece

TZ024-435

Lock nut

PNT600-03

Button Head Cap Screw

PNT600-100

Spacer

PNT600-138

Socket

TNM00365

●SRB-830-480-K2-70L

Nose Assembly

TNM00360

SA Mast Housing

TNM00355

SA Nose Housing

TNM00361

Nose Housing

TNM00257

Nose Slider

PNT600-137A

Slider Spring

AN600P-31

Retaining Ring

AN600P-32

Nosepiece

TZ034-433

Lock nut

PNT600-03

Button Head Cap Screw

PNT600-100

Spacer

PNT600-138

Socket

TNM00366

Lock Nut

Slider Spring

Nosepiece

Retaining Ring

Nose Slider

Button Head Cap Screw

Nose Housing

SA Mast Housing

Spacer

Socket

3. HB Bolt (Made to order)

When tightening HB bolts, replace the mandrel attached to the following nosepiece

and tool with the following socket to make a tool for HB bolts.

HB Bolt

Socket

Nosepiece

SPB-650R-WB*****

PNT600-01-6HB-WB

PNT600-02-6HB-WB

SPB-625-RLT

PNT600-01-6HB

PNT600-02-6HB

4. Slit Nut (Made to order) *Only can be used by Stroke control

When fastening the slit nut, attach the sleeve to the outer diameter of the

mandrel and replace it with the following nose piece. The mandrel used is

PNT600-01-6P.

Slit Nut

Nosepiece

SPH-640-SLIT

PNT600-02-64SLT-S

ENS-M6SV-S

SPH-670-SLIT

PNT600-02-67SLT-S

Nosepiece

Socket

Sleeve

STANLEY Engineered Fastening

4 Shelter Rock Lane

Danbury, Connecticut,

United States, 06810

Tel. 877 364 2781

Fax 800 225 5614

Holding your world together ®

Find your closest STANLEY Engineered Fastening location on

www.stanleyengineeredfastening.com/contact

For an authorized distributor nearby please check

www.stanleyengineeredfastening.com/econtact/distributors

Manual Number

Issue

C/N

TNM00383

210406-1

Avdel®, Avex®, Avibulb®, Avinox®, Bulbex®, Hemlok®, Interlock®, Klamp-Tite®, Monobolt®, POP®,

ProSet®, Stavex® and T-Lok® are registered trademarks of Stanley Black & Decker, Inc. and its affiliates.

The names and logos of other companies mentioned herein may be trademarks of their respective owners.

Data shown is subject to change without pior notice as a result of continuous product development and

improvement policy. Your local STANLEY Engineered Fastening representative is at your disposal should

you need to confirm latest information.

Andere Handbücher für NB08PT-18

Inhaltsverzeichnis

Andere Stanley Elektrowerkzeuge Handbücher

Stanley

Stanley Labounty MDP Series Leitfaden

Stanley

Stanley EZM4000 Bedienungsanleitung

Stanley

Stanley Avdel 74200 Fehlerbehebungshandbuch

Stanley

Stanley FatMax V20 SFMCF900 Bedienungsanleitung

Stanley

Stanley NB08PT-18 Bedienungsanleitung

Stanley

Stanley FATMAX SFMCD750 Bedienungsanleitung

Stanley

Stanley BR45 Bedienungsanleitung

Stanley

Stanley Avdel STD Genesis nG3LB Tool Konfigurationshandbuch

Stanley

Stanley SRR1200 Bedienungsanleitung

Stanley

Stanley NB08PT-18 2.0 Ah Bedienungsanleitung

Stanley

Stanley FATMAX SFMCE100B Bedienungsanleitung

Stanley

Stanley Fatmax SFMCE500 Bedienungsanleitung

Stanley

Stanley SJ45 Bedienungsanleitung

Stanley

Stanley FATMAX V20 SCJ600 Bedienungsanleitung

Stanley

Stanley POP PB3400 Bedienungsanleitung

Stanley

Stanley STEL670 Bedienungsanleitung

Stanley

Stanley MB05 Bedienungsanleitung

Stanley

Stanley 73432-02000 Fehlerbehebungshandbuch

Stanley

Stanley 150703XSTN Bedienungsanleitung

Stanley

Stanley Avdel 07287 Fehlerbehebungshandbuch

Stanley

Stanley Fatmax FME670 Bedienungsanleitung

Stanley

Stanley STGP1318 Bedienungsanleitung

Stanley

Stanley STSJ0600 Bedienungsanleitung

Stanley

Stanley Fatmax SFMCE510 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch