Stanley Tara Non Boiler Eco Bedienungsanleitung

Tara Non Boiler Eco

Solid Fuel Stove

INSTALLATION AND OPERATING INSTRUCTIONS

WARNING: This appliance is hot while in operation and retains its heat for a long period of time after

use. children, aged or infirm persons should be supervised at all times and should not be allowed to

touch the hot working surfaces while in use or until the appliance has thoroughly cooled.

When using the boiler stove in situations where children, aged and/or infirm persons are present a fire-

guard must be used to prevent accidental contact with the stove. The fireguard should be

manufactured in accordance with BS 8423:2002.

TABLE OF CONTENTS

PAGE NO.

1. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Installation check list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Fire Cement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Asbestos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Metal Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4. Pre-Installation Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5. Chimney . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

6. Flues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

7. Flue Pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

8. Top Flue Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

9. Rear Flue Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

10. Ventilation & Combustion Air Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

11. Permanent Air Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Extractor Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

12. Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

13. Installation Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

14. Floor Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

15. Specification Non boiler model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

16. Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

17. Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

18. Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

19. Suitable Fuels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

20. Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

21. Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

22. Air Control Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

23. Air Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

24. Recommended Fuels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

25. Overnight Burning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

26. Re-fuelling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

27. De-Ashing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

28. Disposal of Ashes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

28. Chimney Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

29. To Clean Chimney Outlet (Boiler / Non Boiler Model ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

30. To Replace Fire Grate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

31. CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

32. Fire Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

TABLE OF CONTENTS

PAGE NO.

33. Vitreous Enamel Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

34. Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

35. Glass Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

36. Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

37. Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

STANLEY SOLID FUEL STOVE WARRANTY

CONDITIONS OF WARRANTY

Your Stanley Solid Fuel Stove is guaranteed against any part that fails (under normal operating conditions) as detailed

in the following table with timelines specified from the date of installation of the appliance. If the unit is not installed with-

in six months of date of purchase, the warranty will commence six months from the date of purchase.

Warranty Period Parts Covered (Parts & Labour unless Stated)

Up to 1 Year •Refractory materials (supply only)

•Rope seals, glass seals and cement seals.

•Surface Finish on Seno models.

•Grates and fire bars.

•Ceramic glass is covered for Thermal breakage (supply only).

•Rust (if reported before installation)

•Aesthetic Damage (provided reported on date of receipt)

Up to 5 Years •All external castings & enamel finishes (excluding impact damage or

damage caused by overfiring). Pictures of damage must be submitted to

WS Service Department.

Up to 3 Years •Boiler - A Leaking Boiler Report must be conducted by an Authorised

Stanley Service Engineer and submitted to WS Service Department for re

view.

All warranty claims must be reported to the Waterford Stanley Service Department and must be submitted with the prod-

uct serial number (located on the front casting), date of purchase, proof of purchase (if requested) and details of the

specific nature of the problem.

The warranty is given only to the original consumer/purchaser only and is non- transferable. The appliance must be

installed by a suitable qualified person and installed as per the requirements of the manual. Failure to comply with the

Installation requirements or Building Regulations will void your warranty. Waterford Stanley reserve the right to replace

any part due to manufacturing defect that fails within the warranty period under the terms of the warranty. The unit must

be used for normal domestic purposes only and in accordance with manufacturer's operation instructions.

LIMITS OF LIABILITY

The warranty does not cover:

* Special, incidental or consequential damages, injury to persons or Property, or any other consequential loss.

* Any issue caused by negligence, misuse, abuse or circumstances beyond Waterford Stanley’s control.

* Any issue with wear and tear, modification, alteration, or servicing by anyone other than an authorized service

engineer.

* Installation and operational related problems such as draught related issues external to the stove, inadequate

venting or ventilation, excessive flue offsets, negative air pressure caused by insufficient burning of improper

fuel.

* Damage caused to the unit while in transit.

* Enamel discolouration due to over firing, enamel damage caused by impact, damage to baffles caused by

over firing and fading of surface finish on casting.

* Stress fractures on bricks.

* Rust on cast iron parts unless reported prior to unit being installed.

* Aesthetic damage, rust & missing parts on units purchased off display.

Note: Adequate clearance must be maintained around the appliance to ensure the ease of part removal in the possi-

ble event of their damage/failure. Waterford Stanley are not responsible for any costs incurred in the removal of items

installed in the vicinity of the appliance that have to be moved to facilitate a part replacement.

INSTALLATION CHECK LIST

Flue System

1. Minimum Flue Height of 4.5 metres (15 feet).

2. Appliance should be connected to a minimum of 1.8 metres (6 feet) of 150mm (6”)

flue pipe with a horizontal run not exceeding 150mm (6”).

3. Appliance should be connected to a chimney of less than 200mm (8”) in diameter

(otherwise the chimney must be lined with a 6”flue liner).

4. The chimney venting position must be above the main ridge of the roof or adjacent

outside obstructions.

5. The chimney serving this appliance should not serve any other appliance.

6. Access should be provided to the chimney serving the appliance to allow for cleaning.

Location

7. Clearance to combustible materials must be adhered to as described in the Clearance

to Combustible section.

8. The stove must be installed on a floor protector that covers the area under the stove

and extends 18”to the front & 8”to the sides and back.

Plumbing

9. Appliance must be connected to a gravity circuit using 1”ID flow & return piping.

10. The length of pipes from the cylinder to the cooker should not exceed 7.8 metres

(251/2 feet).

11. A circulation pump should be fitted to the return pipe of the radiator circuit and controlled by

a pipe stat fitted to the flow pipe of the gravity circuit to the cylinder.

(Not applicable to DHW Model).

Ventilation & Combustion Air Requirements

12. The room in which the appliance is located should have an air vent of adequate

size to support correct combustion (see Ventilation & Combustion Air Requirement

Section for specific details).

Tick

TARA SOLID FUEL CENTRAL HEATING STOVE

INSTALLATION & OPERATING INSTRUCTIONS

GENERAL

When installing, operating and maintaining your

Tara Stove respect basic standards of fire safety.

Read these instructions carefully before commenc-

ing the installation. Failure to do so may result in

damage to persons and property. Consult your local

Municipal office and your insurance representative

to determine what regulations are in force. Save

these instructions for future reference.

Please note that it is a legal requirement under

England & Wales Building Regulations that the

installation of the stove is either carried out under

Local Authority Building Control approval or is

installed by a Competent Person registered with a

Government approved Competent Persons

Scheme. HETAS Ltd operate such a scheme and a

listing of their Registered Competent Persons can

be found on their website at www.hetas.co.uk.

Special care must be taken when installing the stove

such that the requirements of the Health & Safety at

Work Act are met.

Handling

Adequate facilities must be available for loading,

unloading and site handling.

Fire Cement

Some types of fire cement are caustic and should

not be allowed to come into contact with the skin. In

case of contact with the skin wash immediately with

plenty of water.

Asbestos

This stove contains no asbestos. If there is a possi-

bility of disturbing any asbestos in the course of

installation then please seek specialist guidance and

use appropriate protective equipment.

Metal Parts

When installing or servicing this stove care should

be taken to avoid the possibility of personal injury.

“IMPORTANT WARNING”

This stove must not be installed into a chimney that

serves any other heating appliance.

There must not be an extractor fan fitted in the same

room as the stove as this can cause the stove to

emit fumes into the room.

The complete installation must be done in accor-

dance with current Standards and Local Codes. It

should be noted that the requirements and these

publications may be superseded during the life of

this manual.

Fig.1

PRE INSTALLATION ASSEMBLY

1. After removing the stove from its pack, open

the front door and remove the contents.

2. Fit the front door handle using the M8 screw,

as shown in Fig.1.

3. Remove the stove from the wooden pallet.

4. Fit the front ash tray by slotting into place on

the front and secure it using the screws

provided.

CHIMNEY

Do not connect to a chimney serving another

appliance.

The stove is a radiant room heater and must be con-

nected to a chimney of the proper size and type.

The chimney must have a cross-sectional area of at

least 30 square inches 18150sq. mm or a diameter

of at least 6”(150mm). It is best to connect to a

chimney of the same size, as connection to a larger

size may result in a somewhat less draught. Do not

connect to a chimney serving another appliance.

Minimum chimney height 15’(4.1 meters) from floor

on which stove is installed. An existing masonry

chimney should be inspected and if necessary

repaired by a competent mason. The stove must be

connected to a chimney with a minimum continuous

draft of .06 wg. Poor draft conditions will result in

poor performance.

In adverse weather conditions, down drafts may be

experienced causing smoke or fumes to spill into the

room. If this occurs shut the appliance down by

closing the air controls. If the problem persists seek

the advice of a chimney sweep.

Fig 2

FLUES

Flues should be vertical wherever possible and

where a bend is necessary, it should not make an

angle of more than 45owith the vertical. Horizontal

flue runs should be avoided except in the case of a

back outlet appliance, when the length of the hori-

zontal section should not exceed 150mm.

In order to minimise flue resistance and to make

sweeping easier it is recommended to use 2 x 45o

bends rather than a 90obend.

The flue termination point must be located to min-

imise any wind effects. Wind effects of suction,

pressure zones and turbulence can be created by

the roof and adjacent objects. Wind effects can also

be created by natural land contours.

To minimise the wind effects, the flue termination

point should be located a minimum of 1000mm from

the roof measured vertically and 2300mm measured

horizontally. Where this termination point does not

2300

1000

Soot Door

Appliance

Fig 3

FLUE PIPES

A flue pipe should only be used to connect an appli-

ance to a chimney and should not pass through any

roof space.

Flue pipes may be of any of the following materials:

(a) Cast iron as described in BS 41: 1973

(1981), or

(b) Stainless steel with a wall thickness of

at least 1mm and as described in BS

EN 10095:1999 Specification for

stainless and heat resisting steel

plate, sheet and strip, for Grade 316

S11, 316 S13, 316 S16, 316 S31,

316 S33, or the equivalent Euronorm

88-71 designation, or

6999: 1989.

Flue pipes with spigot and socket joints should be fit-

ted with the socket uppermost.

Clearance to combustibles must be adhered to

when fitting the flue pipe.

The appliance is suitable for continuous operation

on solid mineral fuel and intermittent operation on

wood logs.

suffice it may be necessary to extend the flue pipe

so that the termination point is above the apex. (See

Fig.3)

TOP FLUE EXIT

For top outlet configuration remove the hob from the

top of the stove, turn the hob upside down and place

it on the floor, taking care not to damage it. Remove

the hob blanking plate by unscrewing the two

screws from underneath the hob.

Next remove the flue blanking plate from the top of

the stove by unscrewing the two screws, connect

this blanking plate to the rear flue outlet at the back

of the stove. Replace the hob in the correct position.

Connect the connector pipe (not supplied) into the

top flue outlet socket at the top of the stove and

cement into place using approved fire cement ensur-

ing that no cement blocks the flue passageway.

Fig 4 VENTILATION & COMBUSTION AIR REQUIRE-

MENTS

It is imperative that there is sufficient air supply to

the stove in order to support correct combustion.

The air supply to this appliance must comply with

B.S. 8303: Part 1.

The minimum effective air requirement for this appli-

ance is 21cm2(3.25in2). When calculating combus-

tion air requirement for this appliance use the fol-

lowing equation: a total free area of at least 550mm2

per kW of rated output above 5kW shall be provid-

ed.

If there is another air using appliance fitted in the

same or adjacent room, it will be necessary to cal-

culate additional air supply.

All materials used in the manufacture of air vents

should be such that the vent is dimensionally stable

and corrosion resistant.

The effective free area of any vent should be ascer-

tained before installation. The effect of any screen

should be allowed for when determining the effective

free area of any vent.

Air vents direct to the outside of the building should

be located so that any air current produced will not

pass through normally occupied areas of the room.

An air vent outside the building should not be locat-

ed less than the dimensions specified within the

Building Regulations from any part of any flue termi-

nal. These air vents must also be fire proofed as per

Building Regulations.

Air vents in internal walls should not communicate

with bedsits, toilets, bathrooms or rooms containing

a shower.

Air vents traversing cavity walls should include a

continuous duct across the cavity. The duct should

be installed in such a manner as not to impair the

weather resistance of the cavity.

REAR FLUE EXIT

For rear flue outlet configuration push in flue con-

nector pipe (not supplied) into flue outlet socket at

the rear of the stove and cement into place using

approved fire cement ensuring that no cement

blocks the flue passageway.

It is recommended that a minimum clearance of

100mm be maintained from the sides and rear of the

appliance to a tiled fireplace or masonry wall, espe-

cially on the right of the appliance as access is

required for the controls.

Fig. 5

Fig.6

It is recommended that this appliance is sited next to

and on a non-combustible surface. A minimum all

round clearance of 100 mm will allow air circulation

and not impede the performance of the stove.

The connector may pass through walls or partitions

constructed of combustible materials provided the

connector is either listed for wall pass-through or is

routed through a device listed for a wall pass-

through and is installed in accordance with the con-

ditions of the listing. Any unexposed metal that is

used as part of a wall pass-through system is

exposed to flue gases shall be constructed of stain-

less steel or other equivalent material that will resist

corrosion, softening, or cracking from flue gas at

temperatures up to 982oC.

FLOOR PROTECTION

It is recommended that this appliance is installed on

a solid, level, non- combustible hearth conforming to

current Building Regulations.

The hearth should extend at least 127mm from the

sides and rear of the stove and 460mm from the

front. See Fig. 6.

Joints between air vents and outside walls should be

sealed to prevent the ingress of moisture. Existing

air vents should be of the correct size and unob-

structed for the appliance in use.

Where such a installation exists, a test for spillage

should be made with the fan or fans and other appli-

ances using air in operation at full rate, (i.e. extrac-

tion fans, tumble dryers) with all external doors and

windows closed.

If spillage occurs following the above operation, an

additional air vent of sufficient size to prevent this

occurrence should be installed.

PERMANENT AIR VENT

The stove requires a permanent and adequate air

supply in order for it to operate safely and efficiently.

In accordance with current Building Regulations the

installer will have fitted a permanent air supply vent

into the room in which the stove is installed to pro-

vide combustion air. This air vent should not under

any circumstances be shut off or sealed.

Extractor Fan

There must not be an extractor fan fitted in the same

room as the stove as this can cause the stove to

emit smoke and fumes into the room.

LOCATION

There are several conditions to be considered in

selecting a location for your Tara Stove.

a. Position in the area to be heated, central

locations are usually best.

b. Allowances for proper clearances to

combustibles.

INSTALLATION CLEARANCES

Clearance to combustible materials (Non Boiler

Model)

From the front - 900mm

From the sides - 460mm

From the back - 700mm

From the flue pipe - 600mm

NON BOILER STOVE SPECIFICATION

TECHNICAL DATA

MODEL NON BOILER

Parameter Wood Mineral smokeless fuel

Max Heat Output (kW) 8 8

Nominal Heat Output (kW) 6.7 7.1

Output to Room (kW) 6.7 7.1

Typical Refuel Interval To Achieve Nominal Outputs(h) 0.8 1

Mean Flue Gas Temp. (oC) 314 304

Efficiency % 80.5 78.3

Flue gas mass flow ( g/s) 4.5 5.6

Gross Weight (kg) 135

Flue Outlet Diameter (mm) 150

Wood Log Size (mm) 300 N/A

Mean CO emission (at 13 % O2) % 0.10 0.11

Mean CnHm (at 13 % O2) Nmg/m3 43 58

Mean NOx (at 13 % O2) Nmg/m3 82 97

DIN Plus dust (at 13 % O2) Nmg/m3 17 32

Note: Dimensions stated are in millimetres and may be subject to a slight +/- variation.

Model Energy

Efficiency Class Heat Output to

Room Heat Output to

Water Energy

Efficiency Index Preferred Fuel Nominal Heat

Output Net Efficiency

Tara NB A+ 7.4 N/A 107.73 Wood 7.4 81.0

Inhaltsverzeichnis

Andere Stanley Herd Handbücher

Stanley

Stanley BRANDON Bedienungsanleitung

Stanley

Stanley IK900 Bedienungsanleitung

Stanley

Stanley K500 Bedienungsanleitung

Stanley

Stanley Ardmore Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Stanley

Stanley Cara Bedienungsanleitung

Stanley

Stanley K100 Bedienungsanleitung

Stanley

Stanley Lismore Bedienungsanleitung

Stanley

Stanley Tara Mk3 Bedienungsanleitung

Stanley

Stanley OISIN MK II Bedienungsanleitung

Stanley

Stanley Lismore Bedienungsanleitung

Stanley

Stanley Oisin Eco Bedienungsanleitung

Stanley

Stanley Oisin Bedienungsanleitung

Stanley

Stanley Erin Bedienungsanleitung

Stanley

Stanley Solis F900 Ridge Bedienungsanleitung

Stanley

Stanley Ardmore Bedienungsanleitung

Stanley

Stanley Lismore Bedienungsanleitung

Stanley

Stanley Aoife Bedienungsanleitung

Stanley

Stanley Cara Bedienungsanleitung

Stanley

Stanley K1200 Bedienungsanleitung

Stanley

Stanley Erin Bedienungsanleitung

Stanley

Stanley Cara Bedienungsanleitung

Stanley

Stanley K1700 Bedienungsanleitung

Stanley

Stanley Ashling Bedienungsanleitung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung

Regency

Regency Ultimate U39E Series Kurzanleitung

Barton

Barton FH-AMP8745 Technisches Dokument

United States Stove Company

United States Stove Company Ashley AP60 Bedienungsanleitung

KYOWA

KYOWA KW-3503 Bedienungsanleitung