Stanley TLX-350FM Bedienungsanleitung

Model : TLX-350FM

TV Mount Installation Guide

Thank you for choosing Stanley – the hardware of choice

for Architects, Contractors, and Home Owners for its quality,

performance and dependability.

Following is your step-by-step instructions for an install

made easy.

If you get stuck, give customer service a call at 1-855-816-6868

You can also reach us at [email protected]

hank

or Architec

per

ormanc

Following is

made eas

Caution: Please read the entire manual before proceeding

View warranty and disclaimer on page 16

Getting Started

Before we start lets make sure we have the correct mount and all

the required tools and hardware to complete the installation.

The TV is a Flat Panel TV is between 32” - 55” and weighs no more than 60lbs.

The Wall the TV will be mounted on is either concrete or dry wall with

wood studs.

You have all of the following tools:

Check out our free level app in the app store!

If you answer “Yes” to all the questions above then you are ready

to begin the TV Mount installation!

13mm

(1/2in)

H1 (x5)

For attaching TV to Mount

Caution: This product contains small items that could be a choking hazard if swallowed.

Parts & Hardware

I1 (x5)

Lag bolt Wall

Anchor

Caution: Before starting assembly, verify all parts are included and undamaged. If any parts are missing or

damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged

parts or previously used parts!

G (x1)

M5x14 (x4)

M6x14 (x4)

M8x20 (x4)

B (x8)

Screws

washer

C (x2)

VESA extension

plate left

M6x30 (x4)

D5 (x4)

G1 G3

M8x30 (x4)

F2 (x4)

F1 (x8)

For attaching Mount to wall

G4 (x5) E (x1) F (x1)

D (x2)

VESA extension

plate right

For extension

VESA plate

Wall mount

I (x1)

Wall cover

upper

J(x1)

Wall cover

lower

HEX Key

Wrench

H (x1)

Level

D8 (x4)

Use the wrench(G) to loosen 2

nuts at upper side of Vesa

plate, leaving a clearance of

about 5 mm from Vesa plate.

Note：Do not detach the 2

nuts.

1Check what screw size will fit

in your TV. (B1,C1,D1,C3,D2)

Note: If Your TV has a curved

back you may need to use

longer screws with spacers

( F1,F2).

Step 1: Preparation

M5x14 (x4)

M6x14 (x4)

M8x20 (x4)

M6x30 (x4)

M8x30 (x4)

5~6mm

Remove 2 nuts at under side,

and remove VESA plate(A)

from Wall Mount(H2).

Check screw hole pattern at

back of TV, and configure

VESA plate accordingly.

Step 2: VESA plate configuration

Tool Required:

Screwdriver

For 200 x 200 / 100 x 100

For 400 x 400 / 300 x 300

For 400 x 200

Caution: Hand tighten with

screwdriver only, over

tightening may damage the

TV!

Do not use an electric drill

for this step!

Then attach the VESA plate

prepared in Step 2 onto the

back of TV using the

appropriate hardware.

Step 3: Attach TV to Mounting Plate

B1/ C1/ D1

G1/G3

D1/C3/D2

C3/D2

B1/C1/D1

G1/G3

Tool Required:

Screwdriver

C3/D1/D2

Use a stud finder to locate 1

stud. Then draw a vertical line

to mark the center of the stud.

Level the wall mount and align

it with the center of the studs.

Make 3 Pencil marks to

indicate where to drill.

Tools Required:

Pencil Stud Finder

Caution: The minimum size of the woodstud must be 1/2”x 3 1/2”

and the thickness of the drywall must not exceed 5/8”.

Level

Wood stud

Step 4A: Install Wall Plate on Drywall with Wood Stud

Note : For Concrete Skip to Step 3B

level

Remove the Wall plate and drill

pilot holes with a 3/16” drill bit. 3

Tools Required:

Drill

3 in.

(75 mm)

3/16 in.

(5 mm)

3/16’’

Drillbit

Align the wall plate with the

pilot holes and insert 3 bolts

through the washer in the pilot

holes and tighten.

Note: Use bubble level to level

the mount before fully

tightening all screws.

Level

13mm

(1/2 in)

Wrench

Level the wall mount and make

5 marks with pencil to show

where to drill the pilot holes.

Remove the wall mount and

drill the pilot holes with a 3/8”

drillbit.

Step 4B: Install Wall Plate on Concrete

Tools Required:

Pencil Drill 3/8’’

Drillbit

3/8 in.

(10 mm)

3 in.

(75 mm)

Caution: The minimum depth of the concrete must be 8”.

Do not drill pilot holes into the mortar between the concrete.

Level

level

3Insert the anchors into the 5

pilot holes. Tap with a hammer.

4Align the wall plate with the

pilot holes and anchors and

insert 5 bolts through the

washer into the anchors and

tighten.

Note: Use bubble level to level

the mount before fully

tightening all screws

Tools Required:

Hammer 13mm

(1/2 in)

Wrench

Level

Inhaltsverzeichnis

Andere Stanley TV-Halterung Handbücher

Stanley

Stanley TLR-EC3211T Bedienungsanleitung

Stanley

Stanley TLR-EC3215T Bedienungsanleitung

Stanley

Stanley TMR-105T Bedienungsanleitung

Stanley

Stanley TLS-210S Bedienungsanleitung

Stanley

Stanley TLS-120T Bedienungsanleitung

Stanley

Stanley TLX-105FM Bedienungsanleitung

Stanley

Stanley TMS-DS1113T Bedienungsanleitung

Beliebte TV-Halterung Handbücher anderer Marken

Ergotron

Ergotron Neo Flex Cantilever UHD Bedienungsanleitung

StarTech.com

StarTech.com FPCEILBTB Bedienungsanleitung

VonHaus

VonHaus 05/038 Bedienungsanleitung

Techlink

Techlink ECHO TV Bedienungsanleitung

Sandstrom

Sandstrom SSTVMC12X Bedienungsanleitung

Sony

Sony SU-WL700 Leitfaden

ICW

ICW SCACC18 Bedienungsanleitung

LG WM-L640V Bedienungsanleitung

Gembird

Gembird WM-65ST-01 Bedienungsanleitung

ERARD

ERARD FiTUP XXL 035320 Bedienungsanleitung

PEERLESS

PEERLESS PLCK-1 Leitfaden

Kanto

Kanto RCF180 Bedienungsanleitung

GEM

GEM GEM GP001 Bedienungsanleitung

Gladiator Joe

Gladiator Joe GJ0A0053 Bedienungsanleitung

Vivotek

Vivotek AM-105 Bedienungsanleitung

Vivo

Vivo VESA STAND-VAD1B Bedienungsanleitung

AmazonBasics

AmazonBasics B07QG3LMG4 Bedienungsanleitung

Secura

Secura QLF210 Bedienungsanleitung