Star Micronics DP-8340 FM-120 Bedienungsanleitung

STAR Micronics, Inc.

DP-8340 FM-120

IBM Document: STAR 06/97 Doc # STAR001

Page 1of 2Copyright International Business Machines, 1997

STAR Model DP-8340 FM-120

Specifications

Integrated Features

• Serial Interface (Modular Jack)

• Friction Feed

• Internal Peripheral Driver

12V Single Cash Drawer Support

• Separate Power Supply

• 1.5 K print buffer

Optional Features

• Journal Paper Cutter

• Parallel Interface

• Cash Drawer Cable

• Sprocket Feed

Print Features

• 5 x 9-Pin Print-Head

• Two Color Printing

• 50 million character print-head life

• Bi-Directional Printer

• 2 Lines/Sec. Print Speed

• 12 Lines/Sec. Paper Feed Speed

• Columns (29@10cpi, 40@12cpi, 44@15cpi)

• Support 4.5”paper

Interface (Serial)

• Full Duplex - Error Checking Protocol

• X-ON / X-OFF Or DTR Handshaking

• Baud Rate: 150,300,600,1200,2400,4800,9600

• Bit Transfers: N,8,1 Or E,7,2

• Asynchronous Synchronization

Dimensions

• 3.9‘’ h X 7.9‘’ w X 7.8‘’ d (Printer Only)

• 3.8’’ h X 5.0’’ w X 6.2’’ d (Power Supply Only)

Weight

• Printer Only 4.19 lb.

• Power Supply 5.51 lb.

Power Supply

• 120V ac to 12V DC @ 2 amp

Switch Settings - SW1

Switch Setting Function

1OFF 150 baud rate

OFF 300 baud rate

OFF 600 baud rate

OFF 1200 baud rate

ON 2400 baud rate

ON 4800 baud rate

ON* 9600 baud rate

2OFF 150 baud rate

OFF 300 baud rate

ON 600 baud rate

ON 1200 baud rate

OFF 2400 baud rate

OFF 4800 baud rate

ON* 9600 baud rate

3OFF 150 baud rate

ON 300 baud rate

OFF 600 baud rate

ON 1200 baud rate

OFF 2400 baud rate

ON 4800 baud rate

ON/OFF* 9600 baud rate

4ON* Stop bit = 1

OFF Stop bit = 2

5ON* DTR/DSR protocol

OFF X-ON/X-OFF protocol

6ON* Data bits = 8

OFF Data bits = 7

7ON* No Parity checked

OFF Parity checked

8ON* Parity selection - Odd

OFF Parity selection - Even

* = Default Setting

Switch Settings - SW2

Pin # Setting Signal Name or Function

1ON* USA Character Set

OFF France Character Set

ON Italy Character Set

OFF Germany Character Set

2ON* USA Character Set

ON France Character Set

OFF Italy Character Set

OFF Germany Character Set

3ON* DP8340F / DP8340S 2 Copy Paper

OFF DP8340S Single Copy Paper

4ON* CR Invalid

OFF CR Valid

* = Default Setting

IBM Document: STAR 06/97 Doc # STAR001

Page 2of 2Copyright International Business Machines, 1997

Modular Jack Connector Layout

Pin # Direction Signal Name or Function

1----- GND or Shield Ground

2----- GND or Frame Ground

3Output Carries data from the printer

4Input Carries data to the printer

5Output SPACE if printer is turned ON

6Output Printer sets MARK if error occurs

7----- GND or Signal Ground

8Output Print sets SPACE if ready to Recv.

Terminal Board Color Layout Chart

Symbol Lead

Color Connected Parts

WH White Clutch Solenoid

YE Yellow Ribbon Shift Solenoid

RE Red Motor Governor Board (+)

BL Black Motor Governor Board (GND)

OR Orange CAM Board (5 VDC)

GR Grey CAM Board (GND)

PI Pink CAM Board (output)

VI Violet Reset Board

BR Brown Motor Governor Board (Brake)

Special Notices

• The maximum size paper roll allowed on paper source

spool is 3-1/8”in diameter

• Do not use ketone, thinner or trichlene cleaners because

this could deform plastic parts of printer.

• Check ribbon for fraying or excessive use. Replace

ribbon with an approved ribbon or print-head’s life will be

shortened

• Use vacuum or air to remove any lint, paper shreds from

printer so printer may function properly.

• Never print without paper or ribbon installed, this will

shorten the print-head’s life.

• Dip switches SW1 & SW2 are located on the exterior of

the back-left side of the printer.

Tool Requirements

• Flatblade Screwdriver

• Phillips Head Screwdriver (M2-M4)

• Vacuum Cleaner

• Compress Air

• Tweezers

• Thickness Gauge (0.15 mm -0.70 mm)

Adjustments

Print-Head Clearance

• Open ribbon access cover on rear of printer

• Remove any paper in printer

• Remove ink ribbons (See Procedures)

• Locate and loosen two screws on top of print-head

• Adjust clearance between the platen and print-head to

.475”±.025”using appropriate thickness guide.

• To stop print-head from sliding tighten the screws.

• Replace Ink Ribbon (See Procedures)

• Add paper and close rear cover.

Procedures

Print Test

• Recycle power to printer and depress FEED button.

• Printer begins to print some test patterns and inf.

• To end the Print Test recycle power to printer.

Removal Of Ink Ribbon Spools

• Open cover on rear of printer if not already done.

• Locate the circular ribbon spools.

• Pop-Up any ribbon spool, but do not remove, by

grabbing the sides of spools and lifting up while pressing

down on the ribbon center post.

• Pop-Up the other ribbon spool the same way.

• Remove both ribbon spools and try to keep spools in the

same L/R positions they were on the printer.

Replacement Of Ink Ribbon Spools

• Take printer OFF-line and open rear cover.

• Position ribbon spools next to printer so they are side by

side with ribbon facing to rear of printer and the red

portion of ribbon is on the bottom.

• While keeping same spool positions place spools on the

L/R ribbon center posts and turn briefly to align keyed

position in ribbon spool to match post.

• While pressing down on spools make sure ribbon

passes between the print-head and the paper.

• Verify that ribbon moves freely and is not caught.

• Close cover and return printer ON-line

Field Replaceable Units

Description OEM Part IBM Part

DP-8340 Printer DP8340FM-120T 06J8792

Power Supply AD8340 90G6384

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics NX-1000 Bedienungsanleitung

Star Micronics

Star Micronics Multi-Font XR-1000 Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Betriebsanleitung

Star Micronics

Star Micronics TSP1000 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP700II Series Bedienungsanleitung

Star Micronics

Star Micronics TSP212 Bedienungsanleitung

Star Micronics

Star Micronics TSP1000 Series Montageanleitung

Star Micronics

Star Micronics NR-10 Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Benutzerhandbuch

Star Micronics

Star Micronics 8111 Gebrauchsanweisung

Star Micronics

Star Micronics Line Thermal Printer Bedienungsanleitung

Star Micronics

Star Micronics TSP143LAN Handbuch

Star Micronics

Star Micronics SP200 Series Bedienungsanleitung

Star Micronics

Star Micronics SP312F Bedienungsanleitung

Star Micronics

Star Micronics SB-10 Bedienungsanleitung

Star Micronics

Star Micronics TSP600 Series Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics LaserPrinter4 Bedienungsanleitung

Star Micronics

Star Micronics PW2000-24 Bedienungsanleitung

Star Micronics

Star Micronics NX-2460C Bedienungsanleitung

Star Micronics

Star Micronics TSP100IIIU Montageanleitung

Star Micronics

Star Micronics LC-90 NX-1010 Bedienungsanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungsanleitung

Star Micronics

Star Micronics SP2000 Bedienungsanleitung

Star Micronics

Star Micronics NB-15 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung