Star Micronics DP8340 Series Bedienungsanleitung

Dot Matrix Printer

DP8340 SERIES

[

SERIAL

INTERFACE

]

USERS ManUal

Federal Communications Commission

Radio Frequency Interference

Statement

is equipment has been tested and found to comply with the limits for a Class A digital device, pur-

suant to Part 15 of the FCC Rules. ese limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. is equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of

this equipment in a residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.

is statement will be applied only for the printers marketed in U.S.A.

Statement of

e Canadian Department of Communications

Radio Interference Regulations

is Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

e above statement applies only to printers marketed in Canada.

Trademark acknowledgments

DP8340: Star Micronics Co. Ltd.

Notice

express permission is forbidden.

•e contents of this manual are subject to change without notice.

•All eorts have been made to ensure the accuracy of the contents of this manual at the time of going to

press. However, should any errors be detected, STAR would greatly appreciate being informed of them.

•e above notwithstanding, STAR can assume no responsibility for any errors in this manual.

TABLE OF CONTENTS

1. OUTLINE........................................................................................... 1

2. UNPACKING AND INSTALLATION ............................................. 2

2-1. Unpacking............................................................................................. 2

2-2. Installation of Paper Holders and Re-Roll Prevention Guard

(Only Model DP8340F) ...................................................................... 3

2-3. Handling Care...................................................................................... 4

2-4. Maintenance ......................................................................................... 5

3. PART IDENTIFICATION AND NOMENCLATURE..................... 6

3-1. Power Supply Unit ............................................................................... 6

3-2. Printer ................................................................................................... 7

3-3. Part Functional Description............................................................... 8

4. INSTALLATION OF INK RIBBON AND PAPER .......................... 9

4-1. Installation of Ink Ribbon................................................................... 9

4-2. Removal of Ink Ribbon..................................................................... 10

4-3. Paper Insertion................................................................................... 11

4-3-1. Model DP8340F...........................................................................11

4-3-2. Model DP8340S ...........................................................................12

4-4. Paper Removal ................................................................................... 13

5. CONTROL CODES ......................................................................... 14

6. GENERAL SPECIFICATIONS ....................................................... 15

7. INTERFACE FOR MODEL DP8340M

MODULAR JACK CONNECTOR............................................... 19

7-1. Interface Specications ..................................................................... 19

7-2. Interface Circuit................................................................................. 19

7-3. Setting of the DIP Switches .............................................................. 20

7-3-1. DIP-SW 1......................................................................................20

7-3-2. DIP-SW2.......................................................................................20

7-4. Connectors and Signals..................................................................... 21

7-5. Interface Connections....................................................................... 22

7-6. Peripheral Unit Drive Circuit........................................................... 23

7-6-1. Cable Connection........................................................................24

7-6-2. Peripheral Drive Circuit .............................................................25

7-6-3. Control Codes..............................................................................25

8. INTERFACE FOR MODEL DP8340D

DSUB 25 PIN CONNECTOR ..................................................... 26

8-1. Interface Specications ..................................................................... 26

8-2. Interface Circuit................................................................................. 27

8-2-1. RS-232C ........................................................................................27

8-2-2. Current Loop................................................................................27

8-3. Setting of the DIP Switches .............................................................. 28

8-3-1. DIP-SW 1......................................................................................28

8-3-2. DIP-SW 2......................................................................................28

8-4. Jumper Setting.................................................................................... 29

8-4-1. Removal of the Bottom Cover ...................................................29

8-4-2. Setting of Jumper.........................................................................29

8-5. Connectors and Signals..................................................................... 30

8-6. Interface Connections....................................................................... 31

8-7. Peripheral Unit Drive Circuit........................................................... 32

8-7-1. Cable Connection........................................................................33

8-7-2. Peripheral Drive Circuit .............................................................34

8-7-3. Control Codes..............................................................................34

9. DATA STRUCTURE AND CONTROL.......................................... 35

9-1. DTR Mode (1 BLOCK)..................................................................... 35

9-2. X-ON/X-OFF Mode.......................................................................... 36

9-3. STX-ETX Mode ................................................................................. 38

10. CHARACTER CODE LIST........................................................... 40

11. FONT LIST..................................................................................... 43

12. WHEN POWER IS SUPPLIED BY THE USER........................... 47

13. FERRITE CORE INSTALLATION EU ONLY ......................... 48

– 1 –

1. Outline

e DP8340 series of serial dot matrix printers is for use in ECR, POS, electronic

instruments, banking machines and computer peripheral equipment.

e DP8340 series include the following features;

1) 2 color printing (Red and Black)

2) High-speed bidirectional printing (2 line/sec, 40 columns per line)

3) 9-pin print head

4) The interface conforms to RS-232C in M type, and to RS-232C/20mA

Current Loop in D type.

5) Commands for expanded characters, inverted characters, emphasized

characters, and red and black printing are provided, which makes the printer

very versatile.

6) Simultaneous Data Communication and Printing

7) Error Checking Protocol

8) Peripheral Driver

9) Reverse Channel providing status and full control

Model Name Notation

DP8340 F M

Interface

Paper Feed

D: D-sub 25 Pin Connector

( RS-232C / 20mA Current Loop )

M: Modular Jack Connector

( Only RS-232C )

F: Friction Type

S: Sprocket Type

– 2 –

2. unpacking and installatiOn

2-1. Unpacking

Aer opening the box, check if all necessary accessories are included.

(A) Printer

(B) Power Supply Unit (Option: PS8340A)

Figure 2-1. Unpacking

1Printer

2User’s Manual

3Paper Holders

4Re-Roll Prevention Guard

5Ink Ribbon

6DIP Switch Cover

7Ferrite Core (EU only)

1Power Supply Unit

2User’s Manual

– 3 –

2-2.

Installation of Paper Holders and Re-Roll Prevention Guard

(Only Model DP8340F)

Install the Paper Holders in the outermost holes in the rear of the printer.

Figure 2-2. Installation of Paper Holders

Install the Re-Roll Prevention Wire in the holes of the printer cover. Twisting the

Wire as shown in the gure below, will make the installation easier.

Figure 2-3. Installation of Re-Roll Prevention

– 4 –

2-3. Handling Care

1. Be careful not to drop paper clips, pins or other foreign matter into the unit

as these cause the printer to malfunction.

2. Do not attempt to print when either paper or ribbon cartridge is not located

in the printer, otherwise the print head can be damaged.

3. Do not open the cover while printing.

4. Do not touch the print head immediately aer printing as it gets very hot.

5. Use only roll paper that is not glued to the core.

6. When the paper end mark appears on the paper, replace the roll paper before

it runs out.

WARNING

PShut down your equipment immediately if it produces smoke, a strange

odor, or unusual noise. Immediately unplug the equipment and contact

your dealer for advice.

PNever attempt to repair this product yourself. Improper repair work can be

dangerous.

PNever disassemble or modify this product. Tampering with this product

may result in injury, re, or electric shock.

PDuring and immediately aer printing, the area around the print head is

very hot. Do not touch it, as you could be burned.

CAUTION

P

We recommend that you unplug the printer from the power outlet

whenever you do not plan to use it for long periods. Because of this, you

should locate the printer so that the power outlet it is plugged into is

nearby and easy to access.

P

If the voltage shown on the label on the of your printer does not match the

voltage for your area, contact your dealer immediately.

P

Make sure that the printer is turned o and unplugged from the AC outlet

and that the computer is turned o before making connections.

P

Do not connect a telephone line into the modular connector.

PDo not pull out paper while the printer cover is closed.

PIf liquids, foreign objects (coins and paper clips), and so on enter the

printer, turn o the printer, unplug it from the AC outlet, and contact your

dealer for advice. Continued use could cause a short circuit, which may

result in re or electric shock.

– 5 –

2-4. Maintenance

Essentially, your printer is a robust piece of equipment, but should be treated

with a modicum of care in order to avoid malfunctions. For example:

1. Keep your printer in a “comfortable” environment. Roughly speaking, if you

feel comfortable, then the environment is suitable for your printer.

2. Do not subject the printer to physical shocks or excessive vibration.

3. Avoid over-dusty environments. Dust is the enemy of all precision

mechanical devices.

4. To clean the exterior of the printer, use a cloth barely dampened with either

water with a little detergent or a little alcohol, but do not allow any liquid to

fall inside the printer.

5. The interior of the printer may be cleaned with a small cleaner or a

compressed-air aerosol (sold for this purpose). When performing this

operation, be sure not to bend or damage any cable connections or electronic

components.

– 6 –

DC Power Connector (Output)

Shape of AC Power plug will

vary according to destinations.

part identificatiOn and nOmenclature

3-1. Power Supply Unit (Option)

Model name : PS8340A

Input : 100 to 240V AC, 50/60 Hz

Output : DC12V 5% 2.0A

Figure 3-1. Power Supply Unit

Andere Handbücher für DP8340 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics Star SCP700 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP700 Series Bedienungsanleitung

Star Micronics

Star Micronics TUP400 Series Bedienungsanleitung

Star Micronics

Star Micronics SP700 Series Bedienungsanleitung

Star Micronics

Star Micronics SP2000 Bedienungsanleitung

Star Micronics

Star Micronics TSP600 Series Bedienungsanleitung

Star Micronics

Star Micronics NX-2420 Multi-Font Bedienungsanleitung

Star Micronics

Star Micronics TSP143IIU Bedienungsanleitung

Star Micronics

Star Micronics NX-10 Bedienungsanleitung

Star Micronics

Star Micronics LC-8521 Bedienungsanleitung

Star Micronics

Star Micronics 347F Bedienungsanleitung

Star Micronics

Star Micronics FVP10 SERIES Bedienungsanleitung

Star Micronics

Star Micronics DP-8340 FM-120 Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Montageanleitung

Star Micronics

Star Micronics TUP500 series Bedienungsanleitung

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-6211 Bedienungsanleitung

Star Micronics

Star Micronics NX-1000 Bedienungsanleitung

Star Micronics

Star Micronics SP312F Bedienungsanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungsanleitung

Star Micronics

Star Micronics Multi-Font NX-2415 Bedienungsanleitung

Star Micronics

Star Micronics LC-500 Bedienungsanleitung

Star Micronics

Star Micronics NX-1020 Bedienungsanleitung

Star Micronics

Star Micronics TCP300II Series Montageanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung