Star Micronics Multi-Font XR-1000 Bedienungsanleitung

MULTI-FONT

XR-1000

MULTI-FONT

XR-1500

USERS MANUAL

NOT INTENDED FOR SALE

Federal Communications Commission

Radio Frequency Interference Statement

‘hia quipment generates and uses radio frequency energy and if not installed and used properly, that

is, in strict acco&nce with the manufacturer’s instructions, may cause interference to radio and

is no guarantee that interference will nd occur in a particular installation. If this equipment does cause

interfetena to radio or television reception, which can be determined by turning the qu@nent off and

on, the user is mcoumged to try to correct the interference by one or more of the followmg measures:

. Reorient the receiving antemta

l Relocate the computer or printer with respect to the receiver

l Move the computer 0Tprinter away from the receiver

l Plugthecamputerorprinterintaae~toutletmthatitendtheracdverarcondifferentbranch

If nece=the user should consult the dealer or an experimced radioAelevisicm technician for

additional suggestions.The user may find the following bookleh

tiats Commission helpful: “How to Idmtify and Resdve ~~~=g~!g=;~~~~;

booklet is available from the U.S. Govemmmt Printing Off&, Washington, D.C., 20402, Stock No.

004~ooo-003454.

For compliance with the Federal Noise Interference Standard, this quipment requires a shielded cable.

The above sto~emm~ applies only to printers marketed in the USA.

Statement of

The Canadian Department of Communications

Radio Interference Regulathns

This digital av ntus does not exceed the Class B limits for radio noise emissions from digital apparatus

set out m the .

pdlo Interference Regulations of the Canadian Department of Communications.

Lx @sent appareil numerique n&et pas de bruits radic&ctriques &passant les limites applicables aux

aIpamils mm&i ues de la classe B prescrites dam le Reglement surle brouillage radio6lectrique edict6

par le minis&e 2

es Cumnunications du Canada.

The above stotemen~ applies only IOprinters morketcd in Conoda.

Trademark Acknowledgements

XR-1000, XR-1500, ND-10115, NR-10/l% Star Micronics Co., Ltd

IBM PC, PC-AT, PC-XT, Proprinter, Proprinter II, PC-DOS: International Business Machines

Corp.

Microsoft BASIC, MS-IKXI: Microsoft Corporaticu

EX-800, EX-1000, FX46e, FX-2&k Seiko Epson Corp.

WordStar: MicroPro International Corporation

NOTICE

l All rights resewed. Reproduction of any part of this manual in any form whatsoever without

STAR’s express

l lhecontentsof ~nnission is forbidden.

manual are sub+ to change without notice.

. All efforts have been made to msure the accuracy of the contents of this manual at the time of

g?gowever, should any errors be detected. STAR would greatly appreciate being informed

l ‘lhe above notwithstanding, STAR can assume no responsibility for any errors in this manual.

CONGRATULATIONS

Thank you for buying this printer. This printer is provided with the follow-

ing features:

l 2 print modes - Draft and Near Letter Quality

l Many different typefaces built into the printer

l Epson or IBM Proprinter compatibility including graphics

l Comprehensive paper-handling facilities (cut-sheet or tractor as stan-

dard, with optional Automatic Sheet Feeder)

l Paper-park facility for loading cut-sheet paper without having to

unload fanfold paper

l Memory Switch facility, enabling comprehensive programming from

the front panel

l Optional color facilities

ORGANIZATION OF THIS MANUAL

This manual is divided into 9 chapters. Use chapters 1through 3 as a “User

Guide”, giving you information on how to set up and start your printer. The

remaining chapters may be treated as a reference guide for programming

operations, etc. It assumes a degree of knowledge off the operation of

computers (for instance, it assumes you know about hexadecimal numbers).

The chapters am as follows:

Chapter 1 - Introduction

Read this section first, as it explains how to unpack and install your printer.

Chapter 2 - Front panel controls

There am a number of controls on the front panel which perform various

functions related to paper handling, print modes and font selection. This

section shows you how to use the front panel controls.

Chapter 3 - Setting up the Memory Switches

Your printer has a Memory Switch function, which allows you to make

certain system settings ftom the front panel. This section explains the

operation of these Memory Swithes.

Chapter 4 - Emulations and escape codes

This chapter explains the different emulations provided by your printer, and

the software commands used to drive it. This section is of use if you ate

writing or modifying programs to take advantage of the printer’s features.

Chapter 5 - DIP Switches

This section explains how to set the DIP switches to make system settings

on the printer.

Chapter 6 - MS-DOS and your printer

Since the PC or PC-AT family of computers nmning under MS-DOS is

currently the most popular configuration of microcomputer, we have in-

cluded a few hints and tips to help you use your printer with such systems.

Since virtually allPCsaresold with aMicrosoft BASICinterpreter, we have

also included some hints, and a sample program in this language to

demonstrate the capabilities of the printer.

Chapter 7 - Troubleshooting and maintenance

This section give achecklist of points to check if your printer is not working

in the expected way. It also includes details of some routine maintenance

operations you can carry out yourself. It is not, however, acomplete service

manual. Call a qualified service engineer if you ate unsure of your ability to

carry out any maintenance or servicing operations.

Chapter 8 - Specifications

This section gives the specifications of your printer.

Chapter 9 - Character sets

These charts give the different character sets available, and the differences

between national character sets (as set up with the DIP switches).

TABLE OF CONTENTS

Chapter 1 INTRODUCTION 1

LOCATING THE PRINTER .......................................................... 1

UNPACKING, SETTING UP AND CONNECTION .................... 1

Setting up ..................................................................................... 3

Connection ................................................................................... 5

LOADING PAPER ........................................................................ .7

Cut-sheet paper ............................................................................ 7

Fanfold paper (continuous) stationery ......................................... 8

Once the paper has been loaded ................................................ 10

Chapter 2 FRONT PANEL CONTROLS 11

CONTROLS AND INDICATORS ............................................... 11

controls ..................................................................................... 11

Indicators ................................................................................... 11

PITCH SETTING .......................................................................... 12

Pitch Panel Lock ........................................................................ 12

FONTSETTING ........................................................................... 13

Font Panel Lock ......................................................................... 13

QUIET MODE .............................................................................. 13

PAPER HANDLING .................................................................... 14

Form feed ................................................................................... 14

Paper parking ............................................................................. 14

Short tear-off function ............................................................... 15

Micro Feed ................................................................................. 16

BUFFER CLEAR/RESET ............................................................ 16

TEST AND MAINTENANCE SETTINGS ................................ .16

Chapter 3 SETTING UP THE MEMORY SWITCHES 17

MENU OPTIONS ......................................................................... 19

Command Menu ...................................... .:.

.............................. .19

Font menu ........

.......................................................................... 19

Print Menu ................................................................................ .20

Paper Menu.. ............................................................................. .20

Forms Menu ............................................................................... 21

Factory settings.. ....................................................................... .22

Chapter 4 EMULATIONS AND ESCAPE CODES 23

EMULATIONS ............................................................................. 23

NUMERICAL REPRESENTATION ........................................... 23

COMMAND CODES AND ESCAPE SEQUENCES ................. .24

Font style and character set control cedes ................................ .26

Font pitch control cedes ........................................................... .30

Special print mode control cedes ............................................. .32

Line space control cedes.. ......................................................... .36

Form feed control codes ........................................................... .39

Margins and vertical tab setting control codes ......................... .4 1

Horizontal print position control codes .................................... .44

Downloaded character control codes.. ...................................... .48

Graphics .................................................................................... .52

Miscellaneous codes ................................................................. .55

ASCII command sequences.. .................................................... .63

Chapter 5 DIP SWITCHES 67

Chapter 6 TROUBLESHOOTING AND MAINTENANCE 69

TROUBLESHOOTING ............................................................... .69

Power supply ............................................................................ .70

Printing ..................................................................................... .70

Paper feeding ............................................................................ .72

MAINTENANCE ........................................................................ .75

ADJUSTING THE PRINTING GAP .......................................... .75

RIBBON REPLACEMENT.. ....................................................... .76

REPLACING THE PRINT HEAD .............................................. .78

FRONT PANEL DIAGNOSTIC AND

TEST MODES ............................................................................. .80

Short test mode ......................................................................... .80

Long test mode ......................................................................... .8 1

Text test mode .......................................................................... .82

Hexadecimal dump mode ......................................................... .83

Bidirectional test/adjustment mode .......................................... .84

Chapter 7 MS-DOS AND YOUR PRINTER 87

INSTALLING APPLICATION SOFTWARE

WITH YOUR PRINTER .............................................................. 87

GRAPHICS HARD COPY .......................................................... .89

SETTING UP THE PRINTER FROM THE DOS PROMPT ....

..89

PROGRAMMING USING BASIC ............................................. .90

Sample program ........................................................................ .90

How the program works ........................................................... .93

Patches necessary to use the BASIC interpreter.. ..................... .96

Chapter 8 SPECIFICATIONS 97

Chapter 9 CHARACTER SETS 101

STANDARD CHARACTER SET #l ......................................... 102

STANDARD CHARACTER SET #2.. ....................................... 104

IBM CHARACTER SET #2 ....................................................... 105

IMB CHARACTER SET #l ....................................................... 107

ADDITIONAL CHARACTER SET.. ......................................... 108

INTERNATIONAL CHARACTER SETS ................................. 109

INDEX 111

chapter I INTRODUCTION

Lllr

c - LOCATING THE PRINTER

The following section covers the unpacking and installation of your printer,

together with information on paper loading and handling (both continuous

and cut-sheet paper).

Before you start unpacking and setting up your printer, make sure that you

have a suitable place on which to locate it. By “a suitable place”, we mean:

l A firm, level surface which is fairly vibration-free

l Away from excessive heat (ie away from direct sunlight and away from

heaters, etc)

l Away from excessive humidity

l Away from excessive dust

9 A location with sufficient space to locate the printer and any paper to be

fed into it, as well as the printed paper coming out

l If you are using aparallel connection to your computer, make sum that it

is within 2m (6ft) of the printer (an RS-232 connection using the optional

RS-232 interface can be made over longer distances).

UNPACKING, SETTING UP AND CONNECTION

Now unpack the contents of the printer shipping container, and make sure

that you have the following:

. The printer itself

. Paper guide assembly

l The platen knob

9 A fabric ribbon

If any of these items am missing, contact your supplier.

User’s manual

Theoptional accessories which you may have ordered with your printer are:

. Serial (RS-232) interface hoard

. Automatic sheet feeder

9 Color option kit

See the installation instructions contained with these optional items for

details of how to attach them to your printer.

Setting up

Place your printer in the position where it is going to be permanently sited,

and remove all packing material from inside the top cover. This packing

material is intended to prevent damage to the printer in transit. You may like

to keep this packing with the printer carton if you intend transporting the

printer for use at a different location.

laten knob

The platen knob should be removed from the accessory box inside the

shipping carton. Mount the platen knob on the shaft on the right-hand side

of the printer. Turn the knob on the shaft before pushing the knob fully into

position.

. NOTE

Before turning the platenknob, always ensure that the power to the printer

is OFF.

Remove the top cover by lifting the front (using the two grips at the side),

and pulling towards you. Now install the ribbon.

1 Use the tensioning knob on the ribbon cartridge to tighten the ribbon if it

is slack (turn clockwise).

2 The ribbon should pass between the print head and the print head shield

(see illustration below).

,Print head shield

3 Use the grips on the side of the ribbon cartridge to help locate the cartridge

(squeeze them inwards gently), and make sure that the spindles on the

cartridge holder fit into the sockets on the cartridge itself.

Ribbon cartridge

I Ribbon tensioning knob

Ribbon holder

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics TSP1000 Series Bedienungsanleitung

Star Micronics

Star Micronics SM-S200 Series Montageanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungsanleitung

Star Micronics

Star Micronics TUP900 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP143IIU Bedienungsanleitung

Star Micronics

Star Micronics HSP7000 Series Bedienungsanleitung

Star Micronics

Star Micronics LC24-20 Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Montageanleitung

Star Micronics

Star Micronics NP-266S Montageanleitung

Star Micronics

Star Micronics LC-7211 Bedienungsanleitung

Star Micronics

Star Micronics DP8340R Series Bedienungsanleitung

Star Micronics

Star Micronics XB24-10 Bedienungsanleitung

Star Micronics

Star Micronics AsuraCPRNT Bedienungsanleitung

Star Micronics

Star Micronics LC-15 Bedienungsanleitung

Star Micronics

Star Micronics lC-10 Bedienungsanleitung

Star Micronics

Star Micronics TUP592 Bedienungsanleitung

Star Micronics

Star Micronics NX-10 Bedienungsanleitung

Star Micronics

Star Micronics Line Thermal Printer Bedienungsanleitung

Star Micronics

Star Micronics SP2000 Bedienungsanleitung

Star Micronics

Star Micronics LC-1021 Bedienungsanleitung

Star Micronics

Star Micronics SLIP SP298 SERIES Bedienungsanleitung

Star Micronics

Star Micronics DP8340RC Series Bedienungsanleitung

Star Micronics

Star Micronics SP349 Bedienungsanleitung

Star Micronics

Star Micronics TSP212 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung